EJE-BT0001EYTF3CSFT, TAIYO YUDEN BT IN FUJITSU NOTEBOOKS

FCC ID: EJE-BT0001 (IC: 337J-BT0001) Report No. M060108_Cert_EYTF3CSFT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M060108_Cert_EYTF3CSFT APPENDIX I2 FUJITSU NOTEBOOK USER MANUAL (part 1) Copyright Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guar- antee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trade- marks of Fujitsu Limited. The following are registered trademarks of IBM Corporation: IBM, IBM PC AT, IBM PS/2. ExpressCard TM Compliance ID EC100025. The ExpressCard word mark and logo are owned by the Personal Computer Memory Card International Association (PCMCIA) and any use of such marks by Fujitsu Computer Systems Corporation is under license. MS, MS-DOS, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. PCMCIA is a trademark of the Personal Computer Memory Card International Association. Intel and Pentium are registered trademarks of Intel Corpora- tion or its subsidiaries in the United States and other countries. The Bluetooth trademark is owned by Bluetooth SIG, Inc., USA. Adobe, Acrobat, and Acrobat Reader are either registered trade- marks or trademarks of Adobe Systems Inc. in the United States and/or other countries. Dolby Headphone is manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. Quicken® is a registered trademark of Intuit, Inc., or one of its subsidiaries, in the United States and other countries. Norton AntiVirus is a registered trademark of Symantec Corporation in the United States and other countries. WinDVD is a registered trademark of InterVideo, Inc. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection tech- nology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. All other trademarks mentioned herein are the property of their respective owners . © Copyright 2005 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or trans- mitted in any electronic form without the written consent of Fujitsu. B6FH-6031-01EN-00 WARNING Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name:Fujitsu Computer Systems Corporation Address: 1250 E. Arques Avenue, M/S 122 Sunnyvale, CA 94085 Telephone:(408) 746-6000 Declares that product:Base Model Configurations: LifeBook S7110 notebook LifeBook S7110D notebook Complies with Part 15 of the FCC Rules. This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device must not be allowed to cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation. S7020.book Page 1 Friday, May 13, 2005 3:49 PM LifeBook S7000 Notebook UL Notice This unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 19 V DC, with a current of 3.15 A. AC Adapter output polarity: ■ When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: ■ Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. ■ Avoid using the modem during an electrical storm. There may be a remote risk of electric shock from lightning. ■ Do not use the modem to report a gas leak in the vicinity of the leak. ■ Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. ■ To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord SAVE THESE INSTRUCTIONS For Authorized Repair Technicians Only System Disposal + ■ For continued protection against risk of fire, replace only with the same type and rating fuse. ■ Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dis- pose of used batteries according to the manufacturer’s instructi on. Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS. S7020.book Page 2 Friday, May 13, 2005 3:49 PM Table of Contents Fujitsu LifeBook ® S7000/7000D Notebook Table of Contents 1 PREFACE Preface About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . 1 Fujitsu Contact Information . . . . . . . . . . . . . . . . . 1 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 GETTING TO KNOW YOUR LIFEBOOK NOTEBOOK Overview Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Locating the Controls/Connectors Top and Front Components . . . . . . . . . . . . . . . . . 6 Left-Side Panel Components . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.

FCC ID: EJE-BT0001 (IC: 337J-BT0001) Report No. M060108_Cert_EYTF3CSFT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M060108_Cert_EYTF3CSFT APPENDIX I2 FUJITSU NOTEBOOK USER MANUAL (part 2) 35 4 User-Installable Features S7020.book Page 35 Friday, May 13, 2005 3:49 PM 36 LifeBook S7000 Notebook S7020.book Page 36 Friday, May 13, 2005 3:49 PM 37 User Installable Features Figure 4-1. Optical Drive Optical Drive There is a variety of media available to use with your system, depending upon the system configuration you have selected. Dual-Layer Multi-Format DVD Writer, DVD/CD-RW Combo drives, and DVD-ROM drives are known as “optical drives”. A CD-R or DVD-R disc can only be written to once; CD-RW or DVD-RW discs can be written to over and over. CD-R and CD-RW discs hold up to 700MB of data. DVD-R and DVD-RW discs hold up to 4.7 GB of data. A dual-layer (single-sided) DVD+R disc can hold up to 8.5 GB of data. Depending upon the configuration of your LifeBook notebook, you may have one of the following drives: ■ Dual-Layer Multi-Format DVD Writer: The Dual- Layer Multi-Format DVD Writer combines seven recordable formats in a single drive (DVD-R, DVD+R, DVD-RW, DVD+RW, DVD-RAM, CD-R, and CD- RW), making it the most versatile drive to date. ■ DVD/CD-RW combo: A DVD/CD-RW combo drive allows you to access movie, software, data, or audio DVD/CDs, and to write data onto recordable CD-R and CD-RW discs. ■ DVD-ROM: A DVD-ROM drive allows you to access software, data, or audio DVDs or CDs. MEDIA PLAYER SOFTWARE Dual-Layer Multi-Format DVD Writer model only: With the Dual-Layer Multi-Format DVD Writer and media player software you can play DVD movies and music CDs on your LifeBook notebook. The media player includes controls which allow you to take full advantage of the features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc. With this drive you can also burn onto recordable dual- layer DVD+R, DVD-R/RW, DVD+R/RW, or CD-R/RW discs. DVD/CD-RW Combo model only: With the combo drive, you can play DVD movies, read audio CDs, and write data onto recordable CD-R or CD-RW discs. DVD-ROM model only: With the DVD-ROM drive, you can read software, audio, or data CDs or DVDs LOADING MEDIA ON YOUR DRIVE To load a disc into your optical drive: 1. Push and release the eject button on the front of the optical drive to open the holder tray. The tray will come out of the LifeBook notebook a short distance. 2. Gently pull the tray out until a media disc can easily be placed in the tray. Media Holder Tray Media Eject Button The Dual-Layer Multi-Format DVD Writer also supports burning and reading DVD- RAM. Windows XP supports burning and reading of DVD-RAM as a standard feature. ■ Do not operate your optical drive unless your LifeBook notebook is sitting on a flat surface. Using a drive when the system is not level may damage the drive or prevent proper operation. ■ Prolonged use of the optical drive, such as watching a DVD movie, will substantially reduce your battery life if no other power source is attached. There may be a protective sheet in the tray from when it was shipped; please make sure it is removed before operating the drive. S7020.book Page 37 Friday, May 13, 2005 3:49 PM 38 LifeBook S7000 Notebook 3. Place the media into the tray, label side up, with the hole in the center of the disc. Snap the disc onto the raised circle in the center of the tray. 4. Gently push the holder tray back in until you hear a click. (Figure 4-2) Figure 4-2. Loading/Ejecting Media REMOVING MEDIA 1. Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the LifeBook notebook a short distance. 2. Gently pull the tray out until the disc can easily be removed from the tray. 3. Carefully remove the media disc from the holder tray. 4. Gently push the holder tray back in until you hear a click. USING THE MEDIA PLAYER SOFTWARE Starting a DVD Movie (DVD Models only) 1. Insert the DVD movie into the optical drive of your notebook. If the CD auto run feature activates, skip Step 2. 2. The first time you insert a movie into the DVD/CD- RW tray, you will be prompted to select what you want the system to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will receive the same prompt whenever you insert a disc. 3. Click OK to close the About DVD Player Performance dialog box and the movie will begin. Opening the Media Player Control Panel With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the media player control panel and the mouse. 1. Right-click on the movie screen to open a dropdown menu for options. 2. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen. Using the Media Player Control Panel The media player software allows you to watch the movie much like a VCR player. You can pause, rewind, fast-forward and stop the movie at any point. 1. To Pause the movie, click the on-screen button. 2. To Rewind the movie, click the  button to rewind to a specific portion of the movie, or the  button to return to the opening screen. ■ You should periodically check for current updated drivers either by using the Fujitsu Driver Update utility (See “Automatically Downloading Driver Updates” on page 67) or by going to the Fujitsu web site at us.fujitsu.com/ computers . ■ All LifeBook DVD players are set to play DVD titles with region code number 1 which is specified for the North Amer- ican market. The region number is a regional restriction code defined by the DVD Forum acting on Hollywood requirements. Different region codes are recorded on video DVD titles for publication in different areas of the world. If the regional code of the DVD player does not mat…

Text truncated - open the document above for the full version.

FCC ID: EJE-BT0001 (IC: 337J-BT0001) Report No. M060108_Cert_EYTF3CSFT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M060108_Cert_EYTF3CSFT APPENDIX I2 FUJITSU NOTEBOOK USER MANUAL (part 3) 69 6 Care and Maintenance S7020.book Page 69 Friday, May 13, 2005 3:49 PM 70 LifeBook S7000 Notebook S7020.book Page 70 Friday, May 13, 2005 3:49 PM 71 Care and Maintenance Care and Maintenance If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. Caring for your LifeBook notebook ■ Your LifeBook notebook is a durable but sensitive electronic device. Treat it with respect and care. ■ Make a habit of transporting it in a suitable carrying case. To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. ■ Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion. ■ Do not attempt to service the computer yourself. Always follow installation instructions closely. ■ Keep it away from food and beverages. ■ If you accidentally spill liquid on your LifeBook note- book: 1. Turn it off. 2. Position it so that the liquid can run out. 3. Let it dry out for 24 hours, or longer if needed. 4. If your notebook will not boot after it has dried out, call your support representative. ■ Do not use your Fujitsu LifeBook notebook in a wet environment (near a bathtub, swimming pool). ■ Always use the AC adapter and batteries that are approved for your notebook. ■ Avoid exposure to sand, dust and other environmental hazards. ■ Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook. ■ Keep the covers closed on the connectors and slots when they are not in use. ■ Do not put heavy or sharp objects on the computer. ■ If you are carrying your LifeBook notebook in a brief- case, or any other carrying case, make sure that there are no objects in the case pressing on the lid. ■ Never position your notebook such that the optical drive is supporting the weight of the notebook. ■ Do not drop your notebook. ■ Do not touch the screen with any sharp objects. Cleaning your LifeBook notebook ■ Always disconnect the power plug. (Pull the plug, not the cord.) ■ Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents. ■ Use a soft cloth to remove dust from the screen. Never use glass cleaners. Storing your LifeBook notebook ■ If storing your notebook for a month or longer, turn your LifeBook notebook off, fully charge the battery(s), then remove and store all Lithium ion batteries. ■ Store your notebook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addi- tion, a faulty battery might damage your LifeBook. ■ Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC). Traveling with your LifeBook notebook ■ Do not transport your notebook while it is turned on. ■ It is recommended that you carry your notebook with you while traveling, rather than checking it in as bag- gage. ■ Always bring your System Recovery CD that came with your notebook when you travel. If you experience sys- tem software problems while traveling, you may need it to correct any problems. ■ Never put your notebook through a metal detector. Have your notebook hand-inspected by security per- sonnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Secu- rity officials may require you to turn your notebook On. Make sure you have a charged battery on hand. ■ When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by Electrical equipment may be hazardous if misused. Operations of this product or simi- lar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables. S7020.book Page 71 Friday, May 13, 2005 3:49 PM 72 LifeBook S7000 Notebook security personnel. You can however, put your hard drive through a properly tuned X-ray machine. ■ Take the necessary plug adapters if you're traveling over- seas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent. BATTERIES Caring for your Batteries ■ Always handle batteries carefully. ■ Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire. ■ Do not drop, puncture, disassemble, mutilate or incin- erate the battery. ■ Recharge batteries only as described in this manual and only in ventilated areas. ■ Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life. ■ Do not leave a battery in storage for longer than 6 months without recharging it. Increasing Battery Life ■ Power your LifeBook notebook through the AC or optional auto/airline adapter whenever possible. ■ If your notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery. ■ Keep brightness to the lowest le…

Text truncated - open the document above for the full version.

Modular Approval Request (per DA 00-1407) FCC ID: __RYYEYTF3CSFT__ Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes, this module has RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Yes, using IC has buffered circuit. 3. The modular transmitter must have its own power supply regulation. Yes, this module has power supply regulator. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. Yes, this module has unique antenna coupler. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, this testing is performed by stand-alone configuration. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. Yes, label of this module is put on PCB. For installer, these attentions are indicated in the manual. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Yes, we provide adequate instructions. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Yes, this module comply RF exposure requirements. For installer these attentions are indicated in the manual. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA).

EMC Technologies Pty Ltd, 57 Assembly Drive, Tullamarine VIC 3043 Australia Ph: +613 9335 3333 Fax: +613 9338 9260 www.emctech.com.au EMC Technologies Pty Ltd ABN 82 057 105 549 57 Assembly Drive Tullamarine Victoria Australia 3043 Ph: + 613 9335 3333 Fax: + 613 9338 9260 email: [email protected] To: TIMCO Engineering Inc. Attention: Certification Manager No. of pages: 1 From: Donna Lennon Date: 8 th February 2006 EMC Ref: M010608_Cert_EYTF3CSFT Subject: FCC & IC APPROVAL – FCC ID: EJE-BT0001, IC: 337J-BT0001 Please receive EMC Technologies’ Report M060108_Cert_EYTF3CSFT for review. The EUT is TAIYO YUDEN Bluetooth Module, Model: EYTF3CSFT installed in Fujitsu notebook PCs. The EYTF3CSFT Bluetooth module was originally certified by TAIYO YUDEN as a modular approval under FCC ID: RYYEYTF3CSFT (Canada ID: 4389AEYTF3CSFT). The intention of this application is to get a Limited Modular approval for this Bluetooth module for use in Fujitsu notebook PCs. The Radio modules are installed in a controlled environment at the Fujitsu notebook production/assembly factory. Limited Modular Approval (LMA) details to cover the following Fujitsu notebook configurations: Fujitsu Notebook Model Bluetooth Module Bluetooth Antenna Antenna Gain dBi S7110 2.78 E8110 -0.22 E8210 EYTF3CSFT Inverted F antenna -0.22 Test results are recorded as follows: DSS Submission EMC Technologies Report – M060108_Cert_EYTF3CSFT Test results - FCC Part 15.247 (Part C), RSS-210 - (Bluetooth results). Documents submitted: Report Number: M060108_Cert_EYTF3CSFT & all Appendices including Modular Letter. Required FCC Forms: Form 731, Agent Authority, Confidentiality Request, Required IC Forms: IC Application form, Agent Authority, Confidentiality request, IC Listing, RF Exposure Statement EMC Technologies Pty Ltd is acting as agent for Fujitsu Ltd during this product approval. Their corresponding FRNs are 0009379173 and 0013134713. Regards ______________ Donna Lennon Report Secretary EMC Technologies Pty Ltd

Federal Communications Commission Date: 5 th February 2006 Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21045 Subject: Request for Confidentiality for FCC Certification Application Company: Fujitsu Limited Pursuant to Rule 47 CFR, Chapter 1, Section 0.457(d)(1)(ii), Fujitsu Limited requests that prior to the equipment authorization grant for the (test sample) the entire application be classified and deemed confidential by the Federal Communications Commission (FCC) and as such be withheld from public inspection. As per 47 CFR, Chapter 1, Section 0.457, the exhibits tendered for the purpose of this grant, contain details of trade secrets and technical data that is not made available to competitors and the general public. This information is treated in a confidential manner by Fujitsu Limited and guarded from disclosure to our competitors. The exhibits outlined below are not routinely made available to Fujitsu Limited, with such access granted only to those specifically involved with this particular project. They contain information detailing the unique technology and circuitry of the product that would be of significant benefit to our competitors. All employees treat this technical data in a confidential manner. The manufacture of this product has taken place after an extensive research and development process that has seen the company invest a considerable amount of time and money. The time and effort taken has enabled the product to meet the specific demands of the competitive market for which it is intended and it would be therefore detrimental to allow competitors easy access to design and development details. Apart from a limited number of employees, the information has previously only been disclosed to the Test House responsible for conducting testing and authorized to act as our agent during the certification process. Pursuant to 47CFR Chapter 1, Section 0.459, Fujitsu Limited requests post-grant confidentiality for the following items, ensuring that this material continue to be withheld from public inspection following the grant. Exhibits: Schematics, Block Diagram, Operational Description, Antenna Information, Appendix B3 – Bluetooth Location Photographs Sincerely Yours,

To: TIMCO ENGINEERING INC. Fax: Attention: CERTIFICATION OFFICER Phone: From: EMC TECHNOLOGIES PTY LTD No of pages: 2 EMC Ref: M060108 Date: 3 rd March 2006 Subject: FCC ID: EJE-BT0001 (Request for additional information) TIMCO job # 363AC6 1. Label location: Please confirm that this device is for installation in Grantee’s product only? (i.e. not sold to second OEM). Please address item 6 of DA00-1407. No information was found in this filing other than the Modular approval cover letter. Yes, this device is for Fujitsu Notebooks only. Please see attached revised label for this application. 2. The label shows an additional FCC ID. Please explain compliance with possible co-location and co-transmission with another transmitter. Alternatively, please confirm that this FCC ID/filing is for the BT transmitter only. A statement could be included in the cover letter for clarification. As explained in the main body of the test report, this is for BT transmitter only. The separation distance between the WLAN and BT antennas is greater than 20cm. Therefore, they are not co-located transmitters. Co-location issues are covered in the submitted test report. 3. Band-edges compliance: compliance in the restricted band above 2483.5 MHz is based on the limit of 15.209 (pk 74 and Avg 54dBuV/m). The screen captures provided are not sufficient to show compliance with these limits. Please provide additional information. Using the market delta method as prescribed under DA00-75 requires reporting the High channel maximum field strength level. The delta (from the plots) is then subtracted from the fundamental amplitude (dBuV/m) to obtain the level at the band-edges. Additional information provided. Refer to attachment – Additional Bandedge_BT. 4. The file name “Appendix I1 Bluetooth User Manual.pdf” is marked as confidential on the header of each page. The exhibit does not appear to be necessary for this filing. Please confirm that you are not requiring that this file be uploaded with this filing. Please comment if you would like. OK, Please do not upload this if not required. Thanks. EMC Technologies Pty Ltd ABN 82 057 105 549 57 Assembly Drive Tullamarine Victoria Australia 3043 Ph: + 613 9335 3333 Fax: + 613 9338 9260 email: [email protected] 5. Confidentiality letter: Please include the exhibit “Appendix B3- BT Location Photos.pdf”, as to prevent providing the user with info on how to remove this device and associated antennas, etc. Please refer to revised Bluetooth confidentiality letter. 6. Part 15.207 - Attachment 3 lifebook test report: It is not clear whether the BT transmitter was operating during the tests reported. Please, explain. If so what configuration was evaluated (i.e. channel, power, data rate, etc.) The Bluetooth was configured in different modes of operation for frequencies and power setting and the emissions measured were mainly from the Host NoteBook PC. The Bluetooth emissions were insignificant in this range. For final testing, the Bluetooth was operating in default transmit mode as shown in the main body of the test report under sample operating conditions.

FCC ID: EJE-BT0001 (IC: 337J-BT0001) Report No. M060108_Cert_EYTF3CSFT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M060108_Cert_EYTF3CSFT APPENDIX B1 Test Sample External Photographs FCC ID: EJE-BT0001 (IC: 337J-BT0001) Report No. M060108_Cert_EYTF3CSFT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au Bluetooth – EYTF3CSFT

FCC ID: EJE-BT0001 (IC: 337J-BT0001) Report No. M060108_Cert_EYTF3CSFT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043…

Text truncated - open the document above for the full version.