EMOIBT21Bluetooth Wireless Dual Alarm Clock

instruction manual Model: iBT22 (For 8605 IC) IB (English) - Adaptor Change to 5V Size: 153mm x 120mm Printing color: Black Date : Dec 24, 2013 P1 Bluetooth Wireless Dual Alarm Clock iBT22 (USA) iBT22B (Canada) Introduction Thank you for purchasing the iHome iBT22. This product is designed to provide high quality wireless sound for your iPad, iPhone, iPod, computer, PDA or other Bluetooth audio device. Along with the included Quick Bluetooth Connection Guide this instruction booklet explains the basic operation and care of the unit. Please read them carefully and keep for future reference. • Place the unit on a level surface away from sources of direct sunlight or excessive heat. • Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. • Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as benzene, thinner or similar materials can damage the surface of the unit. P2 Maintenance FCC ID: EMOIBT21 IC: 986B-IBT21 FCC Information FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This Device complies with RSS-210 of the IC Rules; Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference received, including interference that may cause undesired operation P3 QDID:B021180 This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B)/NMB-3(B) IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. Table of Contents P4 Included/ Meet Your iBT22............................................................................................. 1-2 Installing Clock Backup Batteries .........................................................................................3 The Display/ Setting Up the Unit/ Turning the Unit ON and OFF ..............................................4 Setting the Time/ Daylight Saving Time ................................................................................5 Setting the Alarms/ Reviewing, Arming and Disarming Alarms .................................................6 Resetting the Alarm to Come on the Next Day .......................................................................6 Snooze Operation/ Sure Alarm .........................................................................................7 Using Bluetooth: Pairing Your Device ....................................................................................8 Pairing with a Different Device/ Playing Audio Via Bluetooth/Remote Power On Via Bluetooth .......9 Playing Audio via Aux In..................................................................................................10 Sleep Operation/ Dimmer Operation/ USB Charging ..........................................................11 Consumer Product Safety Guide ................................................................................... 12-13 Troubleshooting ..............................................................................................................14 Warranty......................................................................................................................15 1 Included • iBT22 Alarm Clock • 100V-240V universal AC adaptor* • Backrest • 3 AAA batteries • 12” patch cord P5 power adaptor alarm clock audio cable backrest snoo ze dimmer alm. r eset sleep 1) Insert the front tabs of the included backrest at a slight angle into the slots on top of the unit (behind the buttons). 2) Grip the unit in both hands from front to back as shown and s…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Project No.: 1311C017 Page 2 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 3 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 4 of 11

MODEL: iBT22 - Adaptor change to 5V MODEL PLATE (For 8605 IC) SCALE: 1:1 DATE: Dec 12, 2013 COLOR : BLACK BACKGROUND PRINTING WHITE Clock Backup: 4.5V ‘AAA’ (R03) x 3 Service No: iBT22-A-D Mfd & Serviced by SDI Technologies Inc. www.ihome.com Toll Free: 1-800-288-2792 Made in China Patents: www.ihom.com/patents AC Adaptor: DC 5V 2A FCC ID: EMOIBT21 IC: 986B-IBT21 Model: iBT22 (USA) Model: iBT22B (Canada) MODEL: iBT21BC MODEL PLATE SCALE: 1:1 DATE: July 8, 2013 COLOR : BLACK BACKGROUND PRINTING WHITE Clock Backup: 3V ‘AA’ (R6) x 2 Service No: iBT21-A-A Mfd & Serviced by SDI Technologies Inc. www.ihomeaudio.com Toll Free: 1-800-288-2792 Made in China Patents: www.ihome.com/patents AC Adaptor: DC 7.5V 2A Model: iBT21 FCC ID: EMOIBT21 IC: 986B-IBT21 Clock Backup: 3V ‘AA’ (R6) x 2Service No: iBT21-A-A Mfd & Serviced by SDI Technologies Inc.www.ihomeaudio.comToll Free: 1-800-288-2792 Made in China Patents: www.ihome.com/patents AC Adaptor: DC 7.5V 2A Model: iBT21 FCC ID: EMOIBT21IC: 986B-IBT21 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B) label location

Neutron Engineering Inc. Project No.: 1311C017 Page 5 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 6 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 7 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 8 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 9 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 10 of 11 Neutron Engineering Inc. Project No.: 1311C017 Page 11 of 11

Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 1 of 94 FCC&IC Radio Test Report FCC ID: EMOIBT21 IC: 986B-IBT21 This report concerns (check one): Original Grant Class II Change Issued Date : Dec. 19, 2013 Project No. : 1311C017 Equipment : Bluetooth Wireless Dual Alarm Clock Model Name for FCC : iBT21; iBT21X; iBT22; iBT22X (“X” denote as color of cabinet) Model Name for IC iBT21; iBT22B Applicant : SDI TECHNOLOGIES INC. Address : 1299 Main Street, Rahway, NJ 07065, U.S.A Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Dec. 10, 2013 Date of Test: Dec. 10, 2013~ Dec. 18, 2013 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory: (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL: 0769-8318-3000 FAX: 0769-8319-6000 Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 2 of 94 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 3 of 94 Table of Contents Page 1 . CERTIFICATION 7 2 . SUMMARY OF TEST RESULTS 8 2.1 TEST FACILITY 9 2.2 MEASUREMENT UNCERTAINTY 9 3 . GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 12 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 14 4 . EMC EMISSION TEST 15 4.1 CONDUCTED EMISSION MEASUREMENT 15 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 15 4.1.2 TEST PROCEDURE 15 4.1.3 DEVIATION FROM TEST STANDARD 15 4.1.4 TEST SETUP 16 4.1.5 EUT OPERATING CONDITIONS 16 4.1.6 EUT TEST CONDITIONS 16 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 19 4.2.1 RADIATED EMISSION LIMITS 19 4.2.2 TEST PROCEDURE 20 4.2.3 DEVIATION FROM TEST STANDARD 20 4.2.4 TEST SETUP 21 4.2.5 EUT OPERATING CONDITIONS 22 4.2.6 EUT TEST CONDITIONS 22 4.2.7 TEST RESULTS (BELOW 30MHZ) 23 4.2.8 TEST RESULTS: 30MHZ - 1000MHZ 24 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 31 5 . NUMBER OF HOPPING CHANNEL 46 5.1 APPLIED PROCEDURES 46 5.1.1 TEST PROCEDURE 46 5.1.2 DEVIATION FROM STANDARD 46 5.1.3 TEST SETUP 46 5.1.4 EUT OPERATION CONDITIONS 46 5.1.5 EUT TEST CONDITIONS 46 5.1.6 TEST RESULTS 47 Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 4 of 94 Table of Contents Page 6 . AVERAGE TIME OF OCCUPANCY 48 6.1 APPLIED PROCEDURES / LIMIT 48 6.1.1 TEST PROCEDURE 48 6.1.2 DEVIATION FROM STANDARD 48 6.1.3 TEST SETUP 48 6.1.4 EUT OPERATION CONDITIONS 49 6.1.5 EUT TEST CONDITIONS 49 6.1.6 TEST RESULTS 50 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 62 7.1 APPLIED PROCEDURES / LIMIT 62 7.1.1 TEST PROCEDURE 62 7.1.2 DEVIATION FROM STANDARD 62 7.1.3 TEST SETUP 62 7.1.4 EUT TEST CONDITIONS 62 7.1.5 TEST RESULTS 63 8 . BANDWIDTH TEST 67 8.1 APPLIED PROCEDURES 67 8.1.1 TEST PROCEDURE 67 8.1.2 DEVIATION FROM STANDARD 67 8.1.3 TEST SETUP 67 8.1.4 EUT OPERATION CONDITIONS 67 8.1.5 EUT TEST CONDITIONS 67 8.1.6 TEST RESULTS 68 9 . PEAK OUTPUT POWER TEST 72 9.1 APPLIED PROCEDURES / LIMIT 72 9.1.1 TEST PROCEDURE 72 9.1.2 DEVIATION FROM STANDARD 72 9.1.3 TEST SETUP 72 9.1.4 EUT OPERATION CONDITIONS 72 9.1.5 EUT TEST CONDITIONS 72 9.1.6 TEST RESULTS 73 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 77 10.1 APPLIED PROCEDURES / LIMIT 77 10.1.1 TEST PROCEDURE 77 10.1.2 DEVIATION FROM STANDARD 77 10.1.3 TEST SETUP 78 10.1.4 EUT OPERATION CONDITIONS 78 10.1.5 EUT TEST CONDITIONS 78 10.1.6 TEST RESULTS 79 11 . MEASUREMENT INSTRUMENTS LIST AND SETTING 89 Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 5 of 94 Table of Contents Page 12 . EUT TEST PHOTO 91 Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 6 of 94 REPORT ISSUED HISTORY Issued No. Description Issued Date NEI-FICP-1-1311C017 Original Issue. Dec. 19, 2013 Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 7 of 94 1. CERTIFICATION Equipment : Bluetooth Wireless Dual Alarm Clock Brand Name : iHome Model Name for FCC : iBT21; iBT21X; iBT22; iBT22X (“X” denote as color of cabinet) Model Name for IC : iBT21; iBT22B Applicant : SDI TECHNOLOGIES INC. Manufacturer : SDI TECHNOLOGIES INC. Address : 1299 Main Street, Rahway, NJ 07065, U.S.A Factory : Winty Industries Corporation (Shen Zhen) Co. Ltd. Address : San Lian Industry Zone. Shi Yan Town, Bao An District, ShenZhen, China Date of Test : Dec. 10, 2013~ Dec. 18, 2013 Test Item : ENGINEERING SAMPLE Standard(s) : FCC Part15, Subpart C : 2012 (15.247) / ANSI C63.4 : 2009 / FCC Public Notice DA 00-705, March 30, 2000. Canada RSS-210:2010 RSS-GEN Issue 3, Dec 2010 The above equi…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 91 of 94 12. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 92 of 94 Radiated Measurement Photos 9K~30MHz Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 93 of 94 Radiated Measurement Photos 30~1000MHz Neutron Engineering Inc. Report No.: NEI-FICP-1-1311C017 Page 94 of 94 Radiated Measurement Photos Above 1000MHz

instruction manual Model: iBT21 -Revised IB (English) Size: 153mm x 120mm Printing color: Black Date : Dec 24, 2013 P1 iBT21 Bluetooth Wireless Dual Alarm Clock iBT21 Introduction Thank you for purchasing the iHome iBT21. This product is designed to provide high quality wireless sound for your iPad, iPhone, iPod, computer, PDA or other Bluetooth audio device. Along with the included Quick Bluetooth Connection Guide this instruction booklet explains the basic operation and care of the unit. Please read them carefully and keep for future reference. • Place the unit on a level surface away from sources of direct sunlight or excessive heat. • Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. • Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as benzene, thinner or similar materials can damage the surface of the unit. P2 Maintenance iBT21 FCC ID: EMOIBT21 IC: 986B-IBT21 Update by Dec 24, 2013 FCC Information FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This Device complies with RSS-210 of the IC Rules; Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference received, including interference that may cause undesired operation P3 QDID:B021180 This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B)/NMB-3(B) IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. iBT21 Table of Contents Included/ Meet Your iBT21............................................................................................. 1-2 Installing Clock Backup Batteries .........................................................................................3 The Display/ Setting Up the Unit/ Turning the Unit ON and OFF ..............................................4 Setting the Time................................................................................................................5 Setting the Alarms/ Reviewing, Arming and Disarming Alarms .................................................6 Resetting the Alarm to Come on the Next Day .......................................................................6 Snooze Operation/ Sure Alarm .........................................................................................7 Using Bluetooth: Pairing Your Device ....................................................................................8 Pairing with a Different Device/ Playing Audio Via Bluetooth/Remote Power On Via Bluetooth .......9 Playing Audio via Aux In..................................................................................................10 Sleep Operation/ Dimmer Operation/ USB Charging ..........................................................11 Consumer Product Safety Guide ................................................................................... 12-13 Troubleshooting ..............................................................................................................14 Warranty......................................................................................................................15 P4 iBT21 1 Included • iBT21 Alarm Clock • 100V-240V universal AC adaptor • 2 AA batteries • Stereo audio cable P5 power adaptor stereo audio cable alarm clock 2 AA batteries iBT21 2 P6 Meet Your iBT21 Bluetooth/Pairing Button Aux-in Jack DC Jack Clock Adj. Button USB Charging Port Back Lower Volume Button Raise Volume Button Alarm 2 Button Play/Pause Button Alarm 1 Button Sleep Butt…

Text truncated - open the document above for the full version.