ESX4000592Outbound Rugged Speaker

THE P ERFORMANCE YOU NEED ® ® O U T B O U N D S E R I E S 2 2 3 3 4 4 5 5 Charge Your Speaker Using the USB charging cable, connect your speaker’s DC 5V jack to your PC or a USB charger (not included). „The charging indicator lights red during charging and turns off when charging is complete. „A full charge takes about 3 hours. When fully charged, the speaker is capable of operating for up to 6 hours at medium volume levels. Using a USB charger with output less than 5V 500mA can prolong the charging time. „In Bluetooth mode, if the battery power is low, the speaker will sound “Battery low” to alert you. Lithium Battery Notes Follow the instructions for charging the speaker. Recycle lithium batteries. Do not dispose in the trash. Do not burn or bury batteries. Do not puncture or crush. Do not disassemble. If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool water. Immediately seek medical attention. User’s Guide 4000592 Please read this user’s guide before using your new speaker. Rugged Portable Speaker Use Your Speaker 1. Press and hold the G button to turn on the speaker. A voice sounds “Power on”. The Bluetooth indicator flashes red and blue, indicating the speaker is searching for Bluetooth devices or trying to reconnect to the previously connected device. 2. Activate your device’s Bluetooth function (refer to your device’s user’s guide) and search for devices. When OUTBOUND 4000592 appears in the Bluetooth devices list, pair it to your device. If you are prompted for a PIN, enter 0000. A voice sounds “You are now paired, enjoy.” Package Contents „Rugged Portable Speaker „USB Charging Cable „Carabiner „User’s Guide Features „No cord to tie you down „Water-resistant „Portable, for outdoor use „Stereo sound with powerful bass performance „Rechargeable battery capable of 6-hour playtime „Compatible with most Bluetooth-enabled devices n Caution: Do not operate the speaker if it has been damaged in any way. Do not place heavy objects on top of the speaker. To avoid electromagnetic interference, do not place the speaker on top of a TV or other electrical appliance. 3. You can control your speaker through your device or with the speaker’s buttons. „Press § to start/pause playback. „Press + and – to adjust volume. „To reset the speaker, press § twice while the speaker is searching for Bluetooth devices. 4. To turn off the speaker, press and hold G again until you hear “Power off”. n Note: If your device moves too far from the speaker, the Bluetooth connection may break. The speaker will reconnect if you move the device close to the speaker within 15 minutes. Disconnect Your Device Press and hold § until you hear “Disconnected”. The speaker disconnects the current Bluetooth connection and starts searching for another Bluetooth device. Device Not Pairing? Many Bluetooth-enabled devices, such as speakers, remember the most recently paired source (music, smartphone, etc.) and automatically reconnect when turned on. This is convenient, but can prevent you from connecting to a new source. If you can’t pair your speaker, you may need to disconnect it from its previous source. See “Disconnect Your Device” on this page. Bluetooth Indicator Charging Indicator Volume Control (+/–) Play/Pause On/Off ? 4000592_UG_EN_032014.indd 1-53/20/2014 3:55:03 PM 6 6 7 7 8 8 9 9 10 10 Use AUX You can use a stereo audio cable (not included) to connect your device to the speaker’s AUX jack. n Note: The AUX jack accepts audio cables with plug jacket smaller than 9mm in diameter. Bluetooth is automatically deactivated when AUX is connected. The speaker controls are disabled for AUX connections. Use your device controls to control playback. Attaching Your Carabiner You can use your carabiner to attach the speaker to your travel bag to enjoy music while you are on the road. Printed in China 03A14 4000592 © 2014 Ignition L.P. All rights reserved. Auvio is a registered trademark used by Ignition L.P. Package and user documentation are recyclable. User documentation contains recycled material. The Bluetooth ® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Ignition L.P. is under license. Other trademarks and trade names are those of their respective owners. IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND, IF APPLICABLE, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION OF THE STATED WARRANTY PERIOD. EXCEPT AS DESCRIBED ABOVE, IGNITION L.P. SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OF THE PRODUCT OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF IGNITION L.P. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. You may contact Ignition L.P. at: Ignition L.P. 3102 Maple Ave., Suite 450 Dallas, TX 75201 02/14 For product support, call 1-866-315-0426 „Consult the dealer or an experienced radio/TV technician for help. If you cannot eliminate the interference, the FCC requires that you stop using your product. Changes or modifications not expressly by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition…

Text truncated - open the document above for the full version.

3.5MIC Detection AUX IN Switch SGM3717 Speaker 4 ohm Crystal Oscillator 26MHz switch PLAY/PAUSE VOL+ Bluetooth lifi Opoperation al (PT2308) VOL+VOL- Bluetooth(BTM8630) po wer amp lifi er (P AM8406) MUTE LED Blue & red MCU (HT68F03C) switch PWR LED Regulators LED Red battery, 3.7V/1200mA h （STEP-UP） (MP3221) USB charger (ADS8054) electrical switch TG4435 4000592 Block Diagram 1.8V 3.3V 1.8V audio in/out PIO0 ~ PIO21 AIO0 ~ AIO1 CSR8630 Balun/ Filter (RFBPF1608070A0T) 2.4GHz Radio Regulator Stereo Audio Codec Baseband DSP RAM Kalimba DSP PIO MCU Crystal 26MHz/10ppm EEPROM (T24C64A-1V8) Block Diagram RF in/out 2402 ~ 2480MHz 3.0V-4.2V

4 APPENDIX B Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. Vtrek Dewei Industrial Garden, Shibei Industrial Road, Dashi Town, Panyu Borough,Guangzhou City, Guangdong Province, China 2013-05-17 To whom it may concern, Letter of Agency I, an officer of Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. do hereby authorize Intertek Testing Services (Mr. Shawn Xing) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2007) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, [Name]：Liao Xiaofei [Title]： Engineer

AUVIO 4000437 BL2607 RADIO SHACK 1. ! 4.12.8.L2607011RR B 42.0 mm

Technical Description The equipment under test (EUT) is a Bluetooth Speaker. The EUT will operate 3.7 VDC fully charged rechargeable battery charged by an USB Power Adapter with AC 120V, 60Hz input or PC during the test. For more detail information pls. refer to the user manual. Bluetooth V2.1 Channel List 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 Bluetooth V4.0 Channel List 2402 2404 2406 2408 2410 2412 2414 2416 2418 2420 2422 2424 2426 2428 2430 2432 2434 2436 2438 2440 2442 2444 2446 2448 2450 2452 2454 2456 2458 2460 2462 2464 2466 2468 2470 2472 2474 2476 2478 2480 Modulation Type: GFSK for BT 4.0 and GFSK, π/4DQPSK, 8DPSK for BT 2.1+EDR Bluetooth Version: 4.0 and 2.1 with EDR Antenna Type: Integral antenna Antenna Gain: 0dBi The nominal radiated output power (e.i.r.p) specified: -2 dBm (Tolerance: +/- 3 dB) The nominal conducted output power specified: -2 dBm (Tolerance: +/- 3 dB) The function of main IC is mentioned as below. 1) IC1 acts 5V DC to DC. 2) IC2 acts 3.3V DC to DC 3) IC3 acts POWER AMP 4) IC4-A acts operational amplifier 5) IC4-B acts operational amplifier 6) IC5 acts Audio Switch Processor 7) IC6 acts Regulator 8) IC7 acts Regulator 9) MC1 acts Microcontroller Processor 10) BU1 Bluetooth module In Bluetooth Module: 1) U1 acts as Bluetooth chip. 2) U2 is a filter. 3) U3 acts as EEPROM. 4) Y1 is a 26MHz oscillator for Bluetooth chip.

1 INTERTEK TESTING SERVICES Analysis Report The equipment under test (EUT) is a Bluetooth speaker. The EUT was powered by 3.7 VDC fully charged rechargeable battery charged by an USB Power Adapter with AC 120V, 60Hz input or PC during the test. For more detail information pls. refer to the user manual. Modulation Type: GFSK for BT 4.0 and GFSK, π/4DQPSK, 8DPSK for BT 2.1+EDR Bluetooth Version: 4.0 and 2.1 with EDR Antenna Type: Integral antenna Antenna Gain: 0dBi The nominal radiated output power (e.i.r.p) specified: -2 dBm (Tolerance: +/- 3 dB) The nominal conducted output power specified: -2 dBm (Tolerance: +/- 3 dB) According to the KDB 447498: The maximum radiated emission for the EUT is 94.9dBμV/m ( BT 4.0) at 3m in the frequency 2.480GHz = [(FS*D) ^2 / 30] mW = -0.3dBm which is within the production variation. The minimum radiated emission for the EUT is 91.0dBμV/m (BT 4.0) at 3m in the frequency 2.440GHz = [(FS*D) ^2 / 30] mW = -4.2dBm which is within the production variation. The maximun conducted output power specified is 1dBm = 1.3 mW The source- based time-averaging conducted output power = 1.3 * Duty cycle mW <= 1.3 mW (Duty Cycle<=100%) The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.5 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: ESX4000592

VTREK 0 V0 Mode: Rev Date: Sheet of Design: Check: Approve: Block: 0 Wednesday, June 01, 2011 charging power amplifier DC_DC L R charging indicator SPI RESET Battery MUTE Oscillator 26MHz Crystal MCU 1 CHRG 2 GND 3 BAT 4 VCC 5 PROG IC1 ADS8054A 1 1 2 2 CN1 PH2P R12 1.2k R13 3.3k FB3 7R/3A R14 0R T3T4 D2 SS24 R1510k R1830k R20 15k L22.2uH/2A FB4 7R/2A C6 10uF + EC6 1000uF/10V C9 0.1uF C10 0.1uF L322uH/2AL422uH/2A L5 22uH/2A L6 22uH/2A C11 NC C12 0.01uF C13 NC C14 0.01uF C15 NC C16 NC C17 1uF C21 10uF C22 0.1uF C23 10uF C24 0.1uF C25 1uF 1 1 2 2 CN2 PH2P 1 1 2 2 CN3 PH2P T5T6 T7 T8 R54 100k 1 L_OUT+ 2 PGNDL 3 L_OUT- 4 PVDDL 5 MUTE 6 VCC 7 L_IN 8 VREF 9 MODE 10 R_IN 11 GND 12 SHDN 13 PVDDR 14 R_OUT- 15 PGNDR 16 R_OUT+ IC3 PAM-8406 R22 1k R55 10k 1 LX 2 GND 3 FB 4 EN 5 IN2 6 IN1 IC2 MP3221 R17 150K MARK M2MARKM4 1 +V 2 NO1 3 CO1 4 IN1 5 NC1 6 GND 7 NC2 8 IN2 9 CO2 10 NO2 IC5 SGM3717 C3 4.7uF C4 4.7uF C7 4.7uF R57 1k R58 22k C60 4.7uF C61 4.7uF C62 4.7uF R59 NC R60 NC R61100 C63 0.1uF C65 22uF C68 10uF C69 0.1uF R69 10k R72 6.8k R73 6.8k C27 4.7uF C28 4.7uF Q4 8050 R28 1k R29 47k C31 10uF C33 22uF R31 47k R32 47k 1 GND 2 AIO_0 3 UART_TX 4 UART_RX 5 UART_RTS 6 UART_CTS 7 NC 8 NC 9 NC 10 NC 11 NC 12 SPI_EN 13 GND 14 SPI_MISO 15 SPI_MOSI 16 SPI_CLK 17 SPI_CSB 18 GND 19 GND 20 BT_RESET 21 GND 22 LED_1 23 LED_0 24 PWR 25 GND 26 VBUS 27 CHG_EXT 28 VBAT_SENSE 29 BVAT 30 GND 31 1V8 32 VDD_PADS 33 3V3_USB 34 GND 35 USB_N 36 USB_P 37 GND 38 PIO_9 39 PIO_0 40 PIO_1 41 PIO_8 42 PIO_7 43 PIO_6 44 PIO_21 45 PIO_18 46 LED_2 47 GND 48 MIC_BIAS 49 LINE/MIC_AN 50 LINE/MIC_AP 51 LINE_BN 52 LINE_BP 53 AGND 54 SPK_RN 55 SPK_RP 56 SPK_LN 57 SPK_LP 58 GND 59 RF 60 GND BU1 BTM8630 T9 C34 NC R74 0R C35 NC + EC3 470uF/10v C42 1uF C53 1uF D7 SS14 T10T11T12T13 Q5 NC R33 NC C37 NC R34 NC + EC5 10uF R35 1k R36 1k T15 C38 0.1uF R37 10k R38 10k 1 O 2 - 3 + IC4-A PT2308 7 O 6 - 5 + IC4-B PT2308 R4010k R4110kR4210k R43 10k R4410kR45 10k R4610k R47680R48680 R4910k C39 4.7uF C40 4.7uF C41 4.7uF C43 4.7uF C44 4.7uF C45 4.7uF C46 220pF C47220pF R50 22k C48 220pF R51 22k C49 220pF C66 220pF C67 220pF 4 - 8 + IC4-C PT2308 R52 10 C50 0.1uF R5647k R66 47k C56 22uF C57 22uF R67 3.3k R68 10k C70 470pF R75 3.3k R76 10k C73 470pF 12 3 D1 BAV99 R21k R3 75k R51k R7 1k R8 1M R9 10k R10 1k C1 22uF Q12N3906 + EC2 100uF/10v Q28050 C18 0.1uF C55 22uF R23 1k R16 47k 123456789 101112 CN4FCC1.0-12P R24 10k 1 1 2 2 3 3 4 4 5 5 6 6 CN5CON6P R19 220 T2 T16 T17 T18 T19 T20 T21 T22 T23 T24 T25 T26 T27T30 T34 12 D8 BAT54 1 S 2 S 3 S 4 G 5 D 6 D 7 D 8 D Q6 TG4435 R6 0 1 VDD 2 PA6 3 PA5 4 PA7/RES 5 PA2 6 PA1 7 PA0 8 VSS MC1 HT68F03C R1151k C2NC D3 1N4148 C5 0.1uF C8 10uF R21 330 R26 51k R27 51k R39 51k R53 51k D5 0R T14 C26 4.7uF C29 4.7uF C30 4.7uF C32 4.7uF R71 22k R7722kR7822k R7922k 1 VSS 2 VOUT 3 VIN IC7 TG1802 R80 51k Q3 NC R25 NC R81 NC Q7 8550 R82 1k R83 100k T28 + EC1 220uF/10V T29T41T42T45T46 R84 1k Q8 8550 R85 1k R86 100k R88 1k R89 1k R90 1M R91 150k R63 22k R64 1k C36 NC C51 NC C52 NC C54 NC R65 NC R92 NC R93 0 D4 NC D6 1N4148 C19 NC C20 10uF R30 1k R62 510 C58 0.01uF R70 510 C59 0.01uF R87 100k 1 VSS 2 VOUT 3 VIN IC6 TG1802 D9 1N4148 R4 200 1 OUT 2 GND 3 VDD IC8 NC R94 NC C64 0.1uF C71 NC T1 12 D10 NC + EC4 NC C72 0.1uF R1 NC R95 1k R96 1k VBAT VBAT+ VDD5V USB5V VDD5V VDD5V VDD5V VDD5V MUTE AMP_R AMP_L VBAT STANDBY_SW SPKR_LP SPKR_LN SPKR_RP SPKR_RN LINE_BP LINE_BN LINE_AP LINE_AN VDD5V VBAT USB5V LED1 LED0 BT_PWR 1V8 PLAYVOL+ VOL-STANDBY_SW MUTE_SW VEF VEF SPKR_RNSPKR_RPSPKR_LPSPKR_LN VEF VDD5V BT_L BT_R LINE_L LINE_R AUX_L_IN AUX_R_IN VBAT+ VDD5V MUTE MUTE_SW LED0 VOL- USB5V PLAYLED- PWR_SW VBAT VBAT+ VOL+ LED1 LED- VOL+VOL-PLAY USB5V AUX_R_INAUX_L_IN VBAT+ 1V8 VBAT PWR_SWSTANDBY_SW BT_PWR AUX_SW MU3V MU3V RES PA0 PA2 PA2 PA0 PWR_SW VBAT LINE_ANLINE_APLINE_BP LINE_BN AMP_R AMP_L BT_R BT_L LINE_R LINE_L SGM3005_SW SGM3005_SW VDD5V AUX_SW MUTE_SW SGM3005_SW AMP_R BT_R AMP_L BT_L RES LOW_LED VBAT+ LOW_LED VDD5V LOW_LED VTREK Wednesday, June 01, 2011 0 Block: Approve: Check: Design: of Sheet Date: Rev Mode: V0 0 charging AUX IN FB7 600R T3 T5 T4 1 2 3 4 5 JK2 PJ_327A FB280R/100M T1 T2 5:GND1:VCC 12345 67 89 USB1 USB_MICOR 1 1 2 2 3 3 4 4 5 5 6 6 CN5 CON6P R11680 R19680 ESD2 ESD ESD3 ESD C19 220pF C20 220pF T6T7T8T11T12 ESD1ESD FB1 80R/100M C2 0.1uF D5 NC MARK 1 M1 MARK MARK 1 M2 MARK C1 0.1uF R1 0 T9 R21k AGND USB5V LINE_RINLINE_LIN AGND AGNDLINE_LIN LINE_RIN LINE_LIN LINE_RIN AGND USB5V USB5V AUX_SW AUX_SW AUX_SW VTREK Wednesday, June 01, 2011 0 Block: Approve: Check: Design: of Sheet Date: Rev Mode: V0 0 charging LED bluetooth LED 12 2K1 VOL+ 12 2K2 VOL- 12 2K3 PLAY 1LED1 RED 1LED2 RED/BLU T1 T2 T3 T4 T5 T6 T7 T8 T9 12 2K8 VOL- 12 2K5 PALY 12 2K6 VOL+ 12 2K7 ST 12 2K4 ST 123456789 101112 2CN1 FCC1.0-12P T10 T19 1LED3 NC T20 LED-USB5V LED0 LED1 VBAT_OUT VOL+ PLAY VOL- VBAT VOL- USB5V PLAY LED- PWR LED0 VBAT VBAT_OUT VOL+ PWR LED1 PWR VOL- PLAY VOL+ LOW_LED LOW_LED 1 2 3 4 5 6 7 8 ABCD 8 7 6 5 4 3 2 1 D CBA BT S heet:1of1 Dra wn: Checked By: Date:2013-08-04 d Approver By: C12 2u 2 C10 47 0nF C8 15p F C3 2u2 VBAT C4 10n F L1 4.7uH C74u7 C6 10n F C2 2u2 C1 2u2 R1 2K2 R2 2K2 R3 2K2 C13 10 0nF 1V8 PIO_ 10 PIO_11PIO_12 AO 1 A1 2 A2 3 GND 4 SDA 5 SCL 6 WP 7 VCC 8 U3 T 24C64A_1V8 Y1 26M R &D Rev No:V01A C92u2 IN 4 OUT 2 GND 1 GND1 3 U2 RFB PF1608070A0T RF_I N L2 4.7uH C11 10 0nF PWR 3V3_ USB 1V8 1V35 1V8 VBAT_SENSE CHG_EXT VBUS LED_ 0 LED_1LED_2 PIO_ 18 PIO_7PIO_6PIO_21 SPI_ MOSI SPI_MISOSPI_CSBSPI_CLKSPI_EN UART _RX UART_TX AIO_ 0 USB_PUSB_NBT_Reset PIO_ 12 PIO_10PIO_11 SPKR_LP SPKR_LN LINE/MIC_AN LINE_BP PIO_ 0 PIO_1 BT_R F 12 MIC_BIAS 2 SPK R_RN 6 SPK R_RP 7 GND PADDLE 69 VSS_SMPS_1V8 46 VSS_SMPS_1V35 51 AU_REF 1 LINE_BN 4 LINE_BP 5 SPK R_LN 9 SPK R_LP 10 RSTB 3 5 USB_ N 55 USB_ P 56 AIO( 0) 20 PIO( 17)/UART_CTS# 32 PIO( 16)/UART_RTS# 27 PIO( 15)/UART_TX# 21 PIO( 14)/UART_RX# 23 PIO( 13)/QSPI_IO(1) 31 PIO( 11)/QSPI_IO(0)/I2C_SDA 26 PIO( 10)/QSPI_FLASH_CLK/I2C_SCL 25 PIO( 12)/QSPI_FLASH_CS#/I2C_WP 22 SPI_ PCM_SEL 29 PIO( 5)/PCM1_CLK/SPI_CLK 34 PIO(…

Text truncated - open the document above for the full version.

BT 2.1 with EDR BT 4.0

BT 2.1 with EDR BT 4.0

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF No.: FCC 15C_TX_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. Application For Certification FCC ID: ESX4000592 Outbound Rugged Speaker Model: 4000592 Bluetooth version: BT 2.1with EDR 2.4GHz Transceiver Report No.: 140212009SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-13] Prepared and Checked by: Approved by: Sign on file William Chen Project Engineer Billy Li Supervisor Date: March 28, 2014 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESX4000592 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information EXHIBIT 9: Test Equipment List INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESX4000592 ii MEASUREMENT/TECHNICAL REPORT Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. MODEL: 4000592 FCC ID: ESX4000592 This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-13 Edition] provision. Report prepared by: William Chen Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0627 Fax: (86 755) 8601 6751 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESX4000592 iii Table of Contents 1.0 General Description ................................................................................................. 2 1.1 Product Description ................................................................................................. 2 1.2 Related Submittal(s) Grants .................................................................................... 2 1.3 Test Methodology .................................................................................................... 2 1.4 Test Facility ............................................................................................................ 2 2.0 System Test Configuration ...................................................................................... 4 2.1 Justification ............................................................................................................. 4 2.2 EUT Exercising Software ......................................................................................... 4 2.3 Special Accessories ................................................................................................ 4 No special accessories used. ....................................................................................... 4 2.4 Equipment Modification ........................................................................................... 4 2.5 Measurement Uncertainty ....................................................................................... 5 2.6 Support Equipment List and Description .................................................................. 5 3.0 Emission Results ..................................................................................................... 7 3.1 Radiated Test Results ............................................................................................. 8 3.1.1 Field Strength Calculation ..................................................................................... 8 3.1.2 Radiated Emission Configuration Photograph ....................................................... 9 3.1.3 Radiated Emissions .............................................................................................. 9 3.1.4 Transmitter Spurious Emissions ......................................................................... 12 3.2 Conducted Emission at Mains Termina .................................................................. 16 3.2.1 Conducted Emissions Configuration Photograph ................................................ 16 3.2.2 Conducted Emissions ...............................…

Text truncated - open the document above for the full version.

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF No.: FCC 15C_TX_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. Application For Certification FCC ID: ESX4000592 Outbound Rugged Speaker Model: 4000592 Bluetooth Version: 4.0 2.4GHz Transceiver Report No.: 140212009SZN-002 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-13] Prepared and Checked by: Approved by: Sign on file William Chen Project Engineer Billy Li Supervisor Date: March 28, 2014 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESX4000592 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information EXHIBIT 9: Test Equipment List INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESX4000592 ii MEASUREMENT/TECHNICAL REPORT Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. MODEL: 4000592 FCC ID: ESX4000592 This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-13 Edition] provision. Report prepared by: William Chen Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0627 Fax: (86 755) 8601 6751 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESX4000592 iii Table of Contents 1.0 General Description ................................................................................................. 2 1.1 Product Description ................................................................................................. 2 1.2 Related Submittal(s) Grants .................................................................................... 2 1.3 Test Methodology .................................................................................................... 2 1.4 Test Facility ............................................................................................................ 2 2.0 System Test Configuration ...................................................................................... 4 2.1 Justification ............................................................................................................. 4 2.2 EUT Exercising Software ......................................................................................... 4 2.3 Special Accessories ................................................................................................ 4 No special accessories used. ....................................................................................... 4 2.4 Equipment Modification ....................................................................................... 4 2.4 Equipment Modification ........................................................................................... 4 2.5 Measurement Uncertainty ....................................................................................... 5 2.6 Support Equipment List and Description .................................................................. 5 3.0 Emission Results ..................................................................................................... 7 3.1 Radiated Test Results ............................................................................................. 8 3.1.1 Field Strength Calculation ..................................................................................... 8 3.1.2 Radiated Emission Configuration Photograph ....................................................... 9 3.1.3 Radiated Emissions .............................................................................................. 9 3.1.4 Transmitter Spurious Emissions ......................................................................... 12 3.2 Conducted Emission at Mains Termina .................................................................. 16 3.2.1 Conducted Emissions Configuration Photograph ...…

Text truncated - open the document above for the full version.