ESXPBT200Bluetooth speaker

THE PERFORMANCE YOU NEED ® ® PBT200 Portable Bluetooth ® Stereo Speaker User’s Guide 4000452, 4000453 Please read this user’s guide before using your new speaker. 2 2 Package Contents „Bluetooth ® Portable Speaker „USB Charging Cable „User’s Guide Features „No cord to tie you down „Rich, full, and dynamic stereo sound „Built-in speakerphone for answering calls when connected to your mobile phone through Bluetooth wireless technology „Rechargeable Li-poly battery for extended play time, up to 8 hours „Compatible with most Bluetooth wireless technology-enabled tablets, laptops, MP3 players, and smartphones with iOS or Android™ platforms Z Note: You can download Auvio EQ App free from the App Store SM and Google Play™ to customize your calls and music. Not all Android phones can use this app. 3 3 Charge Your Speaker Using the USB charging cable, connect your speaker’s DC 5V jack to your PC or a USB charger (not included) to charge the speaker. „The charging indicator lights red during charging and turns off when charging is complete. „A full charge takes about 3.5 hours. When fully charged, the speaker is capable of operating for up to 8 hours at medium volume levels. Using a charger with output less than 5 V 500 mA can prolong the charging time. „You can charge the speaker in both the ON and OFF modes. „If the battery power is very low, the speaker will sound “low battery” to alert you and turn off. OFF/ON Bluetooth/Charge Indicator 4 4 Use Your Speaker 1. Switch on your speaker; the Bluetooth indicator flashes blue quickly. 2. Activate your device’s Bluetooth function (refer to your device’s user’s guide) and search for device. When AUVIO 4000452 / AUVIO 4000453 appears in the Bluetooth devices list, select it to pair your device with the speaker, the Bluetooth indicator flashes blue every two seconds . 3. You can control your speaker through your device or with the speaker’s § /§, +/–, and / buttons. „If a smartphone is connected and you receive a call, you can answer the call by pressing § /§ and speak into the microphone ( ). „Press and hold § /§ for 3 seconds to disconnect Bluetooth. The speaker starts searching for another Bluetooth device. „If you press the + button and hear a beep, the speaker is at its maximum volume. Volume Control (+/–) Previous/Next Microphone Play/Pause/Receive a Call 5 5 Z Note: If your device uses Bluetooth 2.1 and below, enter the password 0000 for Bluetooth connection. If the speaker is too far from the device, it disconnects from the device and starts searching for another Bluetooth device. If the speaker malfunctions, reset it by pressing § twice when the Bluetooth function is disconnected. Use AUX IN For an audio devices without Bluetooth technology, use an audio cable (not included) to connect it to the speaker’s AUX IN jack. Z Note: Bluetooth is automatically deactivated when AUX IN is connected, even when you leave the audio cable plugged to AUX IN only. Bluetooth is deactivated if your device has an audio cable or earphones plugged in. The controls on the speaker are disabled for AUX IN connections. Use the controls on your audio device to control music playback. 6 6 Care and Caution Do not operate the speaker if it has been damaged in any way. Do not place heavy objects on top of the speaker. To avoid electromagnetic interference, do not place the speaker on top of a TV or other electrical appliance. Lithium Battery Notes: Recycle lithium batteries. Do not dispose in the trash. Do not burn or bury batteries. Do not puncture or crush. Do not disassemble. Charge batteries on a fireproof surface away from flammable items or liquids. Do not charge inside an automobile, especially while driving. If the electrolyte in the cells should get on your skin, thoroughly wash with soap and water. If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention. Follow the instructions for charging the speaker and do not charge longer than recommended. Unplug the USB cable when the battery is charged. 7 7 Specifications Power Input ......................................................... DC 5 V, 500 mA Output .................................................................. 2 W × 2 (Max.) Impedance ............................................................................... 4ȍ Frequency Response .......................................... 100 Hz – 15 kHz Bluetooth Connection Range .....................................30 ft. (9.1m) Bluetooth Protocol ........................................V4.0 +EDR, Class 2 S/N Ratio ......................................................... 65dB (A weighted) Dimensions (HWD) .................4.5x2.5x2.1 inch (115x65x54 mm) Weight .................................................................... 12 oz (340g) Specifications are subject to change and improvement without notice. Actual product may vary from the images found in this document. FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: „Reorient or relocate the receiving antenna. „Increase the separation between the equipment and receiver. „Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 8 8 „Consult the dealer or an experienced radio/TV te…

Text truncated - open the document above for the full version.

KS-2300CD ᮍḚ೒ Bluetooth Module (BTM8640/45 +T24C128A) Crystalloid: 26MHz Step-up DC/DC Converter (EUP2624A) Step-up DC/DC Converter (EUP2624A) BT ANT 1.8V 3.3V 1.8V audio in/out PIO0 ~ PIO21 AIO0 ~ AIO1 CSR8640 Balun/ Filter (RFBPF1608070A0T) 2.4GHz Radio Regulator Stereo Audio Codec Baseband DSP RAM Kalimba DSP PIO MCU Crystal 26MHz/10ppm (T24C128A) RF in/out 2402 ~ 2480MHz EEPROM

4 APPENDIX B Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. Vtrek Dewei Industrial Garden, Shibei Industrial Road, Dashi Town, Panyu Borough,Guangzhou City, Guangdong Province, China 2013-05-17 To whom it may concern, Letter of Agency I, an officer of Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. do hereby authorize Intertek Testing Services (Mr. Shawn Xing) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2007) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, [Name]：Liao Xiaofei [Title]： Engineer

40.6mm 25.0mm 0.1mmPVC( ), ( Radioshack AUVIO PBT-200 ) (REACH ROHS)

Technical Description The equipment under test (EUT) is a Bluetooth Speaker. The EUT will operate from a 3.7Vdc lithium battery which is charged by USB Port. For more detail information pls. refer to the user manual. BT 2.1 Channel List 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 BT4.0 Channel List 2402 2404 2406 2408 2410 2412 2414 2416 2418 2420 2422 2424 2426 2428 2430 2432 2434 2436 2438 2440 2442 2444 2446 2448 2450 2452 2454 2456 2458 2460 2462 2464 2466 2468 2470 2472 2474 2476 2478 2480 Modulation Type: GFSK for BT 4.0 and GFSK, π ππ π/4DQPSK, 8DPSK for BT 2.1+EDR Bluetooth Version: 4.0 and 2.1 with EDR function Antenna Type: Integral antenna Antenna Gain: 0dBi The nominal radiated output power (e.i.r.p) specified for BT 2.1: 6dBm (Tolerance: +/- 3dB) The nominal conducted output power specified BT 2.1: 6dBm (Tolerance: +/- 3dB) The nominal radiated output power (e.i.r.p) specified for BT 4.0: 5dBm (Tolerance: +/- 3dB) The nominal conducted output power specified BT 4.0: 5dBm (Tolerance: +/- 3dB) The function of main IC is mentioned as below. 1) IC1-A. acts AUDIO Amplifier. 2) IC1-B. acts AUDIO Amplifier. 3) IC2 acts POWER Amplifier. 4) IC3. acts Inverting DC/DC. 5) IC4 acts Battery Charger. 6) IC5. Bluetooth Module In Bluetooth Module: 1) U1 acts as bluetooth chip. 2) Y1 is a 26MHz oscillator for Bluetooth chip. 3) U3 acts as EEPROM. 4) U2 is a filter.

1 INTERTEK TESTING SERVICES Analysis Report The equipment under test (EUT) is a Portable Bluetooth speaker. The EUT was powered by DC 3.7V Internal Lithium battery and charging by USB Port. For more detail information pls. refer to the user manual. Modulation Type: GFSK, ∏/4DQPSK, 8DPSK Bl uetooth Version: 2.1 with EDR Antenna Type: Integral antenna Antenna Gain: 0dBi The nominal radiated output power (e.i.r.p) specified: 6dBm ( Tolerance: +/- 3dB) The nominal conducted output power specified: 6dBm ( Tolerance: +/- 3dB) According to the KDB 447498: T he maximum radiated emission for the EUT is 103.5dBμV/m at 3m in the frequency 2.441GHz = [(FS*D) ^2 / 30] mW = 8.27dBm which is within the production variation. The minimum radiated emission for the EUT is 99.9dBμV/m at 3m in the fr equency 2.402GHz = [(FS*D) ^2 / 30] mW = 4.67dBm which is within the production variation. The maximun conducted output power specified is 9dBm = 7.9mW The source- based time-averaging conducted output power = 7.9 * Duty cycle mW= 6.6 mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.5 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: ESXPBT200 2 Transmitter Duty Cycle Calculation Based on the Bluetooth Specification (BT version: 2.1), transmitter duty cycle is dependent of packet type (DH1, DH3 and DH5). For one period for a pseudo-random hopping through all 79 RF channels, for DH5: One hopset consists of 5 TX slot and 1 RX slot. Duty cycle = 5 / 6 = 0.833 This requirement is according to KDB 865664 D02 FCC ID: ESXPBT200

1 INTERTEK TESTING SERVICES Analysis Report The equipment under test (EUT) is a Portable Bluetooth speaker. The EUT was powered by DC 3.7V Internal Lithium battery and charging by USB Port. For more detail information pls. refer to the user manual. Modulation Type: GFSK Bluetooth Version: 4.0 Antenna Type: Integral antenna Antenna Gain: 0dBi The nominal radiated output power (e.i.r.p) specified: 5dBm ( Tolerance: +/- 3dB) The nominal conducted output power specified: 5dBm ( Tolerance: +/- 3dB) According to the KDB 447498: The maximum radiated emission for the EUT is 101.1dBμV/m at 3m in the frequency 2.480GHz = [(FS*D) ^2 / 30] mW = 5.9dBm which is within the production variation. The minimum radiated emission for the EUT is 100.8dBμV/m at 3m in the frequency 2.402GHz = [(FS*D) ^2 / 30] mW = 5.6dBm which is within the production variation. The maximun conducted output power specified is 8dBm = 6.3mW The source- based time-averaging conducted output power = 6.3 * Duty cycle mW=6.3 mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.5 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. Transmitter Duty Cycle Calculation The test signal of the EUT is Continuous emission, so the Duty Cycle is 100%. FCC ID: ESXPBT200

% O X H W R R W K  0 R G X O H $ P S O L I L H U 3 U H D P S O L I L H U 'HVLJQ 9WUHN &KHFN $SSURYH *XDQJ]KRX3DQ\X-XGD&DU 0RGH %ORFN 'DWH $89,23%7 $XGLR(TXLSPHQW&R/WG 5(67 $'6 63. 63.  5 .  ,&$ 37        ,&% 37  5 .   & 3)  5 .   & 3)  5 .  5 .  5 .  5 .   & 8)   & 8)   & 8)   & 8)   & 8)   & 8)   (& X)9  5 .  5 .   & 8)   & 8)  5 .  5 .  39''5  287/  3*1'/  287/  6+'1  95()  ,1/  *1'  9''  ,15  *1'  1&  2875  3*1'5  2875  39''5 ,& 3$0  &8)   5 ¡   5 .  5 .  & 8)  5.  5.  & 8)  & 8)  & 8)  & 8)  & 8)  & 3)  & 3)  & 3)  & 3)   & 8)   & 8)   & 8)  5 .  5 .         ,& (83$  & S)  5 N  5 N  & 8)  5 5  5N  5 .  & 8) ' 66 )% )%5  & 8)  & 8) /; XK  &+5*  *1'  %$7  9&&  352* ,&  &8)  5 N   5 .   5 .   & 8)   & 8)  & 3)  &3)  5 .   5 .   5 . ' 1     &21   5 .   5 .  & 3  & 3 )% )%5  0,&B$3  0,&B%1  0,&B%3  0,&B%$,6  $,2B  567%  9  9B86%  875$B&76  63,B0,62  63,B&6%  63,B&/.  63,B026,  8$57B5;  8$57B576  875$B7;  3,2B  3,2B  3,2B  3,2B  95(*(1$%/(  9%$7  *1'  5)B,2  *1'  0,&B$1  86%B'3  86%B'1  /('B  /('B  /('B  63,B(1  3,2B  3,2B  9&+*  3,2B  *1'  *1'  *1'  3,2B  3,2B  3,2B  3,2B  63.B51  63.B53  63.B/1  63.B/3  $*1' ,& BTM8640/45  (& 8)9 (&'; )% 5 )% & 8)& 5 5 5 73 73 73 73 73 73 73 73 7373 73 73  )% 5)% )% 8+ )% 5 . 5 & 3) & 5 . 5 & 8) & & 8) &                     &21 SLQPP 5 . 5 . 5 . 5 . 5 . 5 . 5 .  (& X)91&   4 %$9   4   (& X)9 5 5 5 . 5 5    4 4627B%&(  5 . 5 0   (& X)9 5 .   $17 3&%$17  & 8)   & 1&   & 1& & 8) & /; 8+ /; 8+ /; 8+ /; 8+ 5 . 5 .             &21 &21'9  & 3)  & 3) & 8)& 5 .   4  5 . 5   & 8) 5 . 5  & 3)  & 3) =' . ' 66  55 %/B5 5B&20 %/B/ /B&20 9'' 9'' '9 9() 9() 9() 9''9 9''9 9''9 6+'1 ,1/ ,15 9'' 9''9 0,&B$1 ,1/ ,15 &+5* 86%B,1 $8;B5,1 $8;B/,1 %$77 ,15 ,1/ B9 *1' 92/ 92/ '2:1 83 /B&20 %/B/ 5B&20 %/B5 3/$<3$86(+) 0,&B$1 0,&B$3 0,&B%,$6 63,B026, 63,B&/.63,B&6% 63,B0,62 B9 /('B 63,B026, 63,B&/.63,B&6% 63,B0,62 63,B(1 *1' %$77 0,&B$3 0,&B$1 0,&B%,$6 3/$<3$86(+) 92/92/ 83 '2:1 B9 9''9 6+'1 '9 9 86%B,1 32: %$77 /(' /(' %$77 /('B &+5* 567% 567% 9 0,& 0,& 86%B,1 Design: Vtrek Check: Approve: Guangzhou Panyu Juda Car Mode: Block: Date: AUVIO PBT200 Audio Equipment Co.,Ltd Polymerlithiumion Battery LED Board Microphone Key Board VOL+ VOL- DOWN UP ONKKEY 1 + 2 - BATT 1:VCC5:GND 12345 USB1 USB-1 USB 1 1 2 2 JP6 1 1 2 2 3 3 4 4 5 5 6 6 JP4 CON6D2.0-V 12 LED2 LED 54 6123 78 SW1 SW_POWER 1 2 R100 5.6K 1 2 3 4 5 6 7 8 91011 JK2 JK_ST3507 MIC1 MIC SW2 SW3 SW5 SW4 SW6 FB9 600R FB8 600R FB7 600R FB6 600R FB5_ 600R FB1_ 600R 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 JP2 10pin,2.0mm R22_ 3.3K R23_ 3.3K R24_ 3.3K R25_ 3.3K R26_ 3.3K FB4_0.22UH FB3_0.22UH 12 LED1 LED USB_IN LED_1BATT+NCNCCHGUSB_IN VDDBATT+POW VDD POW D5V VDD5V AUX_RIN AUX_LIN GND MIC+MIC- 1 2 3 4 5 6 ABCD 6 5 4 3 2 1 D CBA L3 4.7uH C42u2 1V8 3V3_USB C5 2u2 C6 10nF 1V35 VBAT L2 4.7uH C3 2u2 C7 10nF C84u7 VBUS 1V8 C9 15pF C10 2u2 Y1 26M C13 100nF C12 470nF C162u2 C2 2u2 VREGENABLE C112u2 R32K2 R22K2 R12K2 C1 100nF 1V8 PIO_10PIO_11PIO_12 AO 1 A1 2 A2 3 GND 4 SDA 5 SCL 6 WP 7 VCC 8 U3 T24C128A_1V8 PIO_18PIO_19PIO_20PIO_21PIO_12PIO_10PIO_11 TP1 RF BT_RF A3 VSS_BT_LO_AUX A2 VSS_BT_RADIO B3 VSS_DIG_PADS F6 VSS_AUDIO_DRV A5 VSS_SMP_1V8 J8 VSS_SMP_1V35 K9 AUDIO_DCPL A8 MIC_AP A9 MIC_AN A10 MIC_BIAS B9 MIC_BP B7 MIC_BN B8 SPK L_LN B4 SPK L_LP A4 SPK R_RN B6 SPK R_RP A6 RSTB J3 USB_N J10 USB_P H10 AIO(0) D2 UART_CTS/QSPI_RAM_CLK/PIO(17) H2 UART_RTS/QSPI_RAM_CSB/PIO(16) F1 UART_TX/QSPI_IO(3)/PIO(15) D1 UART_RX/QSPI_IO(2)/PIO(14) F2 QSPI_FLASH_IO(1)/PIO(13) G1 I2C_SDA/QSPI_FLASH_IO(0)/PIO(11) G2 I2C_SCL/QSPI_FLASH_CLK)/PIO(10) F5 I2C_WP/QSPI_FLASH_CSB/PIO(12) E2 SPI_PCMB_SEL J4 SPI_CLK/PCM_CLK/PIO(5) J1 SPI_CSB/PCM_SYNC/PIO(4) E1 SPI_MISO/PCM_OUT/PIO(3) J5 SPI_MOSI/PCM_IN/PIO(2) H1 PIO(21) D10 PIO(20) C10 PIO(19) C9 PIO(18) D9 LPC_D7/PCM2_SYNC/QSPI_IO(0)/PIO(7) G10 LPC_CSB/PCM2_IN/UART_RTS/QSPI_FLASH_CSB/PIO(8) E10 LPC_CLK/PCM2_OUT/QSPI_FLASH_CLK/PIO(6) E9 LPC_D6/PCM2_CLK/UART_CTS/QSPI_IO(1)/PIO(9) G9 LPC_D4/UART_TX/QSPI_IO(3)/PIO(1) F10 LPC_D5/UART_RX/QSPI_IO(2)/PIO(0) F9 PIO(31)/LED(2) B10 PIO(30)/LED(1) K1 PIO(29)/LED(0) J2 XTAL_OUT B1 XTAL_IN C1 VDD_PADS_2 E6 VDD_PADS_1 E5 VDD_CORE_DIG_MEM K2 VREGIN_DIG K3 VDD_ANA_BT_LO_RADIO C2 SMPS_SENSE_1V35 K10 LX_1V35 K8 VDD_AUX B2 VDD_AUDIO A7 VDD_AUDIO_DRV B5 VDD_AUX_1V8 A1 SMPS_SENSE_1V8 H9 LX_1V8 K6 VDD_USB/SMP_BYP/VOUT_3V3 J9 VBAT K7 VBAT_SENSE J7 CHG_EXT J6 VCHG K5 VREGENABLE K4 U1 CSR8640 BGA IN 4 OUT 2 GND 1 GND1 3 U2 RFBPF1608070A0T LED_0LED_1LED_2PIO_0PIO_1PIO_6PIO_7PIO_8PIO_9PIO_13AIO_0UART_RXUART_CTSUART_TXUART_RTSUSB_DPUSB_DNRSTBSPI_MOSISPI_MISOSPI_CSBSPI_CLKSPI_EN MIC_AN MIC_AP MIC_BIAS MIC_BP MIC_BN SPK R_RP SPK R_RN SPK L_LN SPK L_LP CHG_EXT VBAT_SENSE RF_IN R510KR410K 1V35

A Att 30 dB * Ref 20.3 dBm Offset 0.3 dB LVL Center 2.4 GHzSpan 10 MHz1 MHz/ * * RBW 100 kHz VBW 300 kHz SWT 2.5 ms 3DB 1 PK MAXH -70 -60 -50 -40 -30 -20 -10 0 10 20 1 Marker 1 [T1 ] 5.67 dBm 2.401980000 GHz 1 Delta 1 [T1 ] -48.39 dB -2.020000000 MHz A Att 30 dB * Ref 20.3 dBm Offset 0.3 dB LVL 1 PK MAXH Center 2.4835 GHzSpan 10 MHz1 MHz/ * * 3DB RBW 100 kHz VBW 300 kHz SWT 2.5 ms -70 -60 -50 -40 -30 -20 -10 0 10 20 1 Marker 1 [T1 ] 7.61 dBm 2.479980000 GHz 1 Delta 1 [T1 ] -53.74 dB 4.000000000 MHz

A Att 30 dB * Ref 20.3 dBm Offset 0.3 dB LVL 1 PK MAXH Center 2.402 GHzSpan 10 MHz1 MHz/ * * 3DB RBW 100 kHz VBW 300 kHz SWT 2.5 ms -70 -60 -50 -40 -30 -20 -10 0 10 20 1 Marker 1 [T1 ] 5.65 dBm 2.401980000 GHz ndB [T1] 20.00 dB BW 1.200000000 MHz T1 Temp 1 [T1 ndB] -13.77 dBm 2.401380000 GHz T2 Temp 2 [T1 ndB] -13.52 dBm 2.402580000 GHz A Att 30 dB * Ref 20.3 dBm Offset 0.3 dB LVL 1 PK MAXH Center 2.48 GHzSpan 10 MHz1 MHz/ * * 3DB RBW 100 kHz VBW 300 kHz SWT 2.5 ms -70 -60 -50 -40 -30 -20 -10 0 10 20 1 Marker 1 [T1 ] 7.61 dBm 2.479980000 GHz ndB [T1] 20.00 dB BW 1.240000000 MHz T1 Temp 1 [T1 ndB] -12.70 dBm 2.479360000 GHz T2 Temp 2 [T1 ndB] -13.20 dBm 2.480600000 GHz

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF No.: FCC 15C_TX_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. Application For Certification FCC ID: ESXPBT200 Bluetooth Speaker Model: 4000452 Additional Model: 4000453 2.4GHz Transceiver Report No.: 130517010SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [ 10-1-12] Prepared and Checked by: Approved by: Sign on file William Chen Project Engineer Andy Yan Project Engineer Date: 10 July 2013 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESXPBT200 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information EXHIBIT 9: Test Equipment List INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESXPBT200 ii MEASUREMENT/TECHNICAL REPORT Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. - MODEL: 4000452 Additional Model: 4000453 FCC ID: ESXPBT200 This report concerns (check one :) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-12 Edition] provision. Report prepared by: William Chen Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0627 Fax: (86 755) 8601 6751 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESXPBT200 iii Table of Contents 1.0 General Description ............................................................................................ 2 1.1 Product Description ............................................................................................ 2 1.2 Related Submittal(s) Grants ............................................................................... 2 1.3 Test Methodology ............................................................................................... 2 1.4 Test Facility ........................................................................................................ 2 2.0 System Test Configuration ................................................................................. 4 2.1 Justification ........................................................................................................ 4 2.2 EUT Exercising Software .................................................................................... 4 2.3 Special Accessories ........................................................................................... 4 2.4 Equipment Modification ...................................................................................... 4 2.5 Measurement Uncertainty .................................................................................. 5 2.6 Support Equipment List and Description ............................................................. 5 3.0 Emission Results ................................................................................................ 7 3.1Radiated Test Results............................................................................ 8 3.1.1 Field Strength Calculation ................................................................................ 8 3.1.2 Radiated Emission Configuration Photograph .................................................. 9 3.1.3 Radiated Emissions ......................................................................................... 9 3.1.4 Transmitter Spurious Emissions (Radiated)............................................ 11 3.2 Conducted Emission at Mains Terminal................................................... 15 3.2.1 Conducted Emissions Configuration Photograph......................................15 3.2.2 Conducted Emissions........................................................................15 4.0 Equipment Photographs ................................................................................... 19 5.0 Product Labelling ......................................................................…

Text truncated - open the document above for the full version.

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF No.: FCC 15C_TX_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Guangzhou Panyu Juda Car Audio Equipment Co., Ltd. Application For Certification FCC ID: ESXPBT200 Bluetooth Speaker Model: 4000452 Additional Model: 4000453 2.4GHz Transceiver Report No.: 130517010SZN-002 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [ 10-1-12] Prepared and Checked by: Approved by: Sign on file William Chen Project Engineer Andy Yan Project Engineer Date: 10 July 2013 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESXPBT200 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information EXHIBIT 9: Test Equipment List INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESXPBT200 ii MEASUREMENT/TECHNICAL REPORT Guangzhou Panyu Juda Car Audio Equipment Co., Ltd.- MODEL: 4000452 Additional Model: 4000453 FCC ID: ESXPBT200 This report concerns (check one :) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-12 Edition] provision. Report prepared by: William Chen Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0627 Fax: (86 755) 8601 6751 INTERTEK TESTING SERVICES TRF No.: FCC 15C_TX_b FCC ID: ESXPBT200 iii Table of Contents 1.0 General Description .................................................................................................................................. 2 1.1 Product Description ..................................................................................................................................... 2 1.2 Related Submittal(s) Grants ....................................................................................................................... 2 1.3 Test Methodology ........................................................................................................................................ 2 1.4 Test Facility ................................................................................................................................................. 2 2.0 System Test Configuration ..................................................................................................................... 4 2.2 EUT Exercising Software ............................................................................................................................ 4 2.3 Special Accessories .................................................................................................................................... 4 2.4 Equipment Modification .........................................................................................…

Text truncated - open the document above for the full version.