EW780-1930-00Video Monitor

RM5754HD/RM5754-2HD RM5764HD/RM5764-2HD RM7754HD/RM7754-2HD RM7764HD/RM7764-2HD RM5854HD/RM5854-2HD Important safety instructions The applied nameplate is located at the bottom of the baby unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1.Follow all warnings and instructions marked on the product. 2.Adult setup is required. 3. 4. CAUTION: Do not install the baby unit at a height above 2 meters. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. 5.This product is not intended for use as a medical monitor. 6.Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 7.CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 8.Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Rechargeable battery information: RM5754HD / RM5754-2HD / RM5764HD / RM5764-2HD RM5854HD / RM5854-2HD / RM5864HD / RM5864-2HD RM7754HD / RM7754-2HD / RM7764HD / RM7764-2HD 3.7V 5000mAh, 18.5Wh Lithium-ion Battery Zhuhai Great Power Energy Co., Ltd. Model: GSP806090-5Ah-3.7V-1S1P 9.The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the- table or cabinet outlet. 10. For pluggable equipment, the socket-outlet (power adapter) shall be installed near the equipment and shall be easily accessible. 11.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 12.Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 13.Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 15.The equipment is to be supplied from an identified USB port complying with the requirements of Limited Power Source. 16. Do not overload wall outlets or use an extension cord. 17.Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 18. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 19.Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 20. To reduce the risk of electric shock, do not disassemble this product, but take it to an 21.You should test the sound reception every time you turn on the units or move one of the components. 22.Periodically examine all components for damage. 23.There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 24. Children should be supervised to ensure that they do not play with the product. 25.The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children. 26. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions •Use and store the product at a temperature between 32 o F and 104 o F. •Burn hazard, fire hazard, explosion hazard associated with mishandling of the battery. •Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. • Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. •Never place the camera unit(s) inside the baby’s crib or playpen. Never cover the camera unit(s) or parent unit with anything such as a towel or a blanket. •Other electronic products may cause interference with your camera unit. Try installing your camera unit as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices): Wireless T…

Text truncated - open the document above for the full version.

Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. Congratulations on purchasing your new VTech product. Before using this HD video monitor, please read Important safety instructions. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, visit www.vtechcanada.com. FrequencyBaby unit: 2412 - 2462 MHz Channels11 LCD5’’ Color LCD (IPS 1280x720 pixels) Nominal effective rangeMaximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirement Parent unit: 3.7V 5000mAh, 18.5Wh Lithium-ion battery Baby unit power adapter: Output: 5V DC @ 1A Parent unit power adapter: Output: 5V DC @ 2A. Specifications are subject to change without notice. © 2022 VTech Communications, Inc. All rights reserved. 05/22. RM5754-XHD_QSG_V4 Technical specifications Android TM and Google Play TM are trademarks of Google Inc. App Store is a trademark of Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1 CONFORMS TO RM5754HD RM5754-2HD 5-inch Smart Wi-Fi 1080p Video Monitor What does HD Video Monitor do? VTech 5-inch Smart Wi-Fi 1080p Video Monitor allows you to stay close to your baby when you are on the move or away. This monitor is Wi-Fi enabled, which uses your home wireless network to stream live video and audio through the HD baby unit and 5-inch color screen parent unit. It allows you to maintain a constant connection to your baby. You can also monitor from your smartphone and mobile tablet. VTech 5-inch Smart Wi-Fi 1080p Video Monitor uses MyVTech Baby Pro app to let you instantly see and hear what’s happening with your baby from anywhere in the world. The app can be downloaded from the App Store or the Google Play TM Store, directly from your smartphone or mobile tablet. Disclaimer and Limitation of Liability VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product. Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada Quick start guide RM5754HD RM5754-2HD For more support information S m Direct mode The parent unit and the baby unit of your video monitor connect to each others in Direct mode by default, which allows you to stream live video right out of the box. Direct mode connection lets you stream live video from parent unit only. • You may experience reduced signal strength if your parent unit and baby unit are far apart, or there are obstructing factors, such as internal walls, between them. Move the parent unit closer to the baby unit to improve the signal strength. You can also set up Router mode to connect via your home Wi-Fi network to improve the connection between your parent unit and baby unit. Router mode You can continue using your video monitor with Direct mode connection, or you can set up your monitor in Router mode connection. Router mode uses your home Wi-Fi network to connect your video monitor. It supports streaming live video through parent unit and smartphone app. We recommend that you set up your monitor in Router mode to enjoy streaming live video via your parent unit with better connection. If you want to stream live video remotely with your mobile device, download and install the MyVTech Baby Pro mobile app. With the mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD video monitor system. It serves as a communicating channel between your baby unit and mobile device, allowing you to monitor and/or control your baby unit wherever you are. For detail, see Download app for mobile access section in this quick start guide. Notes • Your parent unit detects the connection signal strength. If you have connected your video monitor with your home Wi-Fi network, your parent unit automatically switches to direct or router mode - the one that has stronger signal strength. • When both parent unit and app are viewing the camera simultaneously, the video quality will be optimised to deliver the best possible viewing result. Overview What’s in the box Connect, charge and power on the baby monitor CABLE MANAGEMENT x 2 x 2 Important safety instructions Quick start guide Your HD video monitor package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. How the system works VTech cares about your privacy and peace of mind. That’s why we’ve put together a list of industry- recommended best practices to help keep your wireless connection private and your devices protected when online. We recommend you carefully review and consider complying with the following tips. Ensure your wireless connection is secure. • Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2- PSK with AES” setting in your router’s wireless security menu. Change default settings. • Change your wireless router’s default wireless network name (SSID) to something unique. • Change default passwords to unique, strong passwords. A strong password: - Is at least 10 characters long. - Is complex. - Does not contain dictionary words or personal information. - Contains a mix of uppercase letters, lowercase letters, special characters and numbers. Keep your devices up to date. • Download security patches from manufacturers as soon as they become available. This will ensure you always have the latest security updates. • If the feature is available, enable automatic updates for future rel…

Text truncated - open the document above for the full version.

To keep this product working well and looking good, follow these guidelines: • Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). • DO NOT expose it to direct sunlight or moisture. • Avoid dropping the product or treating it roughly. • Clean with a soft cloth. • DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap. • DO NOT use cleaning spray or liquid cleaners. • Make sure the parent unit and the baby unit are dry before you connect them to the mains again. • Clean the USB charging port of dust, dirt, and lint regularly. When you are not going to use the HD video monitor for some time, store the parent unit, the baby unit and the adapters in a cool and dry place. Below are the questions most frequently asked about the HD video monitor. Can I turn off the parent unit screen but keep hearing sound from the baby unit? The parent unit’s LCD display will dim automatically after being inactive for some time. Press MENU/SELECT will turn the LCD display back on. Why does the baby unit not respond normally? Try the following (in the order listed) for common cure: 1. Disconnect the power to the baby unit. 2. Wait a few minutes before connecting power back to the baby unit. 3. Reboot the parent unit. Why is my screen in black and white? The baby unit has a light sensor that measures the ambient light. When the ambient light is dim, such as during nighttime or in a dark room, the baby unit activates its infrared LEDs, and displays the camera view in black and white. Why does my baby unit show offline? Why is the connection lost every now and then? The baby unit may lose the Internet connection. Check your network and the router setting. Other electronic products may cause interference with your baby unit. Try installing your baby unit as far away from these electronic devices as possible. Why don’t I hear a sound/Why can’t I hear my baby cry? The parent unit speaker volume may be too low. Press VOL + to increase the volume. You may have set a low sound sensitivity level. Set the sound sensitivity to a higher level. For details, go to www.vtechphones.com for online help topics. Frequently asked questions General product care Storage mount the baby unit (optional) 1. Place the wall mount bracket on a wall and then use a pencil to mark two holes in parallel. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit). NOTESNOTE Notes • Check for reception strength and camera angle of the baby unit before drilling the holes. • The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your baby units. 2. If you drill the holes into a stud, go to step 3. • If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall. 3. Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole. 3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. 4. Place the baby unit on the wall mount bracket, and then slide it forward until it locks into place. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place. 5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket. Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle. OR 4. Place the baby unit on the wall mount bracket, and then slide it forward until it locks into place. Connect the power adapter to the baby unit and a power supply not controlled by a wall switch. 1 2 Need help? Use your smartphone or mobile device to access our online help. • Go to https://help.vtechphones.com/rm5754hd or https://help.vtechphones.com/rm5754-2hd; OR • Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help. -If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear. If you would like to contact us, visit https://help.vtechphones.com/cs. Download app for mobile access Test the sound level and position the HD video monitor Basic operation S m You can also call our Customer Support at 1-844-848-8324 (1-844-84-VTECH) [in US] or 1-888-211-2005 [in Canada] for help. Driven by system updates, the software, online help topics, and online FAQs will be updated periodically. For operations and guides to help you using your HD video monitor, and for latest information and supports, go and check the online help topics and online FAQs. Auto software and firmware update If you plan to install your baby unit in a designated location, and use your home Wi-Fi network to connect your video monitor, you need to test which of your selected monitoring areas within the house have good Wi-Fi signal strength. After you have powered on your parent unit, you can use your parent unit’s Wi-Fi signal strength indicator to assist in checking. Once you have identified the suitable location, you can install your baby unit. Adjust the distance between your baby unit and the Wi-Fi router if needed. • Depending on surroundings and obstructing factors, such as the effect distance and internal walls have on signal strength, you may experience reduced Wi-Fi signal. To improve the Wi-Fi signal strength, a…

Text truncated - open the document above for the full version.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name VTech Telecommunications Ltd Address 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd, Tai Po NT, Hong Kong Grantee Code EW7 FCC ID EW780-1930-00 Authorized Contact Name Michael Tsui Contact Email [email protected] Contact Phone 852-26805398 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: May 30, 2022 Print Name: Michael Tsui Title: Approbation Supervisor *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

To: Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: VTech Telecommunications Ltd 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT Hong Kong Regarding: Confidentiality Request regarding application for FCC ID: EW780-1930-00 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Michael Tsui Title: Approbation Supervisor Signature: On behalf of Company: VTech Telecommunications Ltd Telephone: 852-26805398 E-mail: [email protected]

VTech Telecommunications Ltd Date: 2022-0 5-3 0 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: EW780-1930-00 To whom it may concern: We, the undersigned, hereby authorize SGS Hong Kong Limited and YW Yung in SGS Hong Kong Limited to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with VTech Telecommunications Ltd. This authorization is valid until further written notice from the applicant. Name (Printed):Michael Tsui Title: Approbation Supervisor Signature: On behalf of Company: VTech Telecommunications Ltd. Telephone: 852 2680 5398

VTech Telecommunications Ltd May, 30, 2022 To whom it may concern, Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows: Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout (Others, please specify) The only differences between these models are the follows for marketing purpose: Color Cosmetic details Trade name Model Number (Others, please specify:Decoration) Suffix (“a, b,x”) represents Color code Packing configuration Others, please specify) a= any alphanumeric character or blank is presenting number of baby unit. b = any alphanumeric character or blank is presenting color option For the product subject to authorization under FCC Declaration of Conformity: In addition, it is to confirm that all the below information 1) the U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual are the same but different in the following model numbers only: Item No. New model Model Number Trade Name Remarks 1 YES RM5754 BU vtech Same as RM7754HD BU 1 Baby unit 2 YES RM5754HD BU Same as RM7754HD BU 1 Baby unit 3 YES RM5754-2HD BU Same as RM7754HD BU 2 Baby units 4 YES RM5754-aHD BU Same as RM7754HD BU a Baby units 5 YES RM5854 BU Same as RM7754HD BU 1 Baby unit 6 YES RM5854HD BU Same as RM7754HD BU 1 Baby unit 7 YES RM5854-aHD BU Same as RM7754HD BU a Baby units 8 YES VM813HD BU Same as RM7754HD BU 1 Baby unit 9 YES VM813-1bHD BU Same as RM7754HD BU 1 Baby unit, “b” color option 10 YES VM813-abHD BU Same as RM7754HD BU a Baby units, “b” color option 11 YES RM7754 BU Same as RM7754HD BU 1 Baby unit 12 YES RM7754HD BU -- 1 Baby unit 13 YES RM7754-2HD BU Same as RM7754HD BU 2 Baby units 14 YES RM7754-aHD BU Same as RM7754HD BU a Baby units 15 YES RM7854 BU Same as RM7754HD BU 1 Baby unit 16 YES RM7854HD BU Same as RM7754HD BU 1 Baby unit VTech Telecommunications Ltd 17 YES RM7854-2HD BU Same as RM7754HD BU 2 Baby units 18 YES RM7854-aHD BU Same as RM7754HD BU a Baby units 19 YES VM816HD BU Same as RM7754HD BU 1 Baby unit 20 YES VM816-1bHD BU Same as RM7754HD BU 1 Baby unit, “b” color option 21 YES VM816-abHD BU Same as RM7754HD BU a Baby units, “b” color option The sample being submitted to SGS for conformity assessment is RM5754HD BU (test model) of the above list. Regards, Michael Tsui Approbation Supervisor

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Appendix A Photographs of EUT Constructional Details for HKEM2205000477AT Appendix A: External Photo of HKEM2205000477AT

Size: 85.2X49mm Material: 50# PET Part No.: 92-XXXXXX-010-100 BU LABELPU LABELGB LABEL S/N: 11 digits, the serial no. is made in VTT barcode system. DiSa: Download from system UPC/DiSa: Font size : Arial ,5 pt. 1.字体：Arial 2.字符UPC：&Disa：需要加粗并加下划线（数字不用加粗） 3.条码尺寸：55~60mm*8mm 4.字符尺寸：55~60mm*2mm 5.字符与条码之前的间距为1mm 6.公差+/- 0.5mm UPC: 7- 3507804853-0 DiSa: xxxxxxxxxxxxxxx DiSa Barcode S/N: XXXXXXXXXXX 55~60mm 1mm 8mm 55~60mm Disa Barcode notes: Model: RM5854HD WIFI MAC: XXXXXXXXXXX WIFI MAC: XXXXXXXXXXX S/N: XXXXXXXXXXX UPC: 7- 3507804853-0 DiSa: xxxxxxxxxxxxxxx DiSa Barcode S/N: XXXXXXXXXXX 5.9mm BU Label 22.3x25.2mm 7.5mm Remark: compliance statement was listed in manual due to surface and interface limitation reason.Remark: compliance statement was listed in manual due to surface and interface limitation reason. WIFI MAC: xxxxxxxxxxxxxx Model: RM5754HD PU S/N: XXXXXXXXXXX Label 28x32mm MANUFACTURED IN CHINA FCC ID: EW780-1930-01 IC: 1135B-80193001 HVIN: 35-400412PU VTech Customer Service 1-800-595-9511 www.vtechphones.com A/V I.C.T.E. WIFI MAC: xxxxxxxxxxxxxx Model: RM5754HD PU S/N: XXXXXXXXXXX MANUFACTURED IN CHINA FCC ID: EW780-1930-01 IC: 1135B-80193001 HVIN: 35-400412PU VTech Customer Service 1-800-595-9511 www.vtechphones.com A/V I.C.T.E. WIFI MAC: xxxxxxxxxxxxxx Model: RM5754-2HD PU S/N: XXXXXXXXXXX MANUFACTURED IN CHINA FCC ID: EW780-1930-01 IC: 1135B-80193001 HVIN: 35-400412PU VTech Customer Service 1-800-595-9511 www.vtechphones.com A/V I.C.T.E. WIFI MAC: XXXXXX HVIN: 35-400351BUD MANUFACTURED IN CHINA FCC ID: EW780-1930-00 IC: 1135B-80193000 Model: RM5754HD BU S/N: xxxxxxxxxxx A/V I.C.T.E. WIFI MAC: XXXXXX HVIN: 35-400351BUD MANUFACTURED IN CHINA FCC ID: EW780-1930-00 IC: 1135B-80193000 Model: RM5854HD BU S/N: XXXXXXXXXXX UPC: 7- 3507804853 -0 DiSa: xxxxxxxxxxxxx A/V I.C.T.E. A/V I.C.T.E. WIFI MAC: XXXXXX HVIN: 35-400351BUD MANUFACTURED IN CHINA FCC ID: EW780-1930-00 IC: 1135B-80193000 Model: RM5754HD BU S/N: xxxxxxxxxxx A/V I.C.T.E. WIFI MAC: XXXXXX HVIN: 35-400351BUD MANUFACTURED IN CHINA FCC ID: EW780-1930-00 IC: 1135B-80193000 Model: RM5754-2HD BU S/N: xxxxxxxxxxx A/V I.C.T.E.A/V I.C.T.E. UPC…

Text truncated - open the document above for the full version.