EW780-2400-00DECT 6.0 Cordless Telephone

Connect the telephone base Specifications are subject to change without notice. © 2021 VTech Communications, Inc. All rights reserved. 03/21. CS6214-X_QSG_V1.0 Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license. T Compatible with Hearing Aid T-Coil TIA-1083 The ENERGY STAR ® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR ® label indicating it meets the latest energy efficiency guidelines. Frequency control Crystal controlled PLL synthesizer Transmit frequency Handset: 1921.536-1928.448 MHz Telephone Base: 1921.536-1928.448 MHz ChannelsDECT channel: 5 Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirement Handset: 2.4V Ni-MH battery Telephone base: 6V DC @ 400mA Charger: 6V DC @ 400mA MemoryPhonebook: 30 memory locations; up to 30 digits and 15 characters Caller ID log: 30 memory locations; up to 24 digits and 15 characters If you subscribe to digital subscriber line (DSL) high-speed Internet service through your telephone line, make sure you connect a DSL filter (not included) to the telephone wall jack. Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. Quick start guide CS6214 CS6214-2 CS6214-11 CS6214-21 VG101 VG101-11 DECT 6.0 cordless telephone Quick start guide THIS SIDE UP / CE CÔTÉ VERS LE HAUT Battery Pack / Bloc-piles : BT162342/BT262342 (2.4V 300mAh Ni-MH) WA RNING / AV ERTISSEMENT : DO NOT BURN OR PUNCTURE BA TTERIES. NE PA S INCINÉRER OU PERCER LES PILES. Made in China / Fabriqué en chine CR1939 THI S SIDE UP / CE CÔ TÉ VERS LE HAUT Battery Pack / Bloc-pi les : BT1 62342 /BT2 62342 (2.4V 300mA h Ni-MH ) WA RNING / AVER TISSE MEN T : DO NO T BU RN OR PUNCTURE BATTERIES. NE PAS INCINÉRE R OU PERCER LES P ILES. Ma de in C hina / Fa briqué en chin e CR1939 THIS SIDE UP Install the battery THIS SIDE UP / C E CÔTÉ VERS LE HAUT Battery P ack / Bloc -p iles : B T16234 2/BT262342 (2.4V 300mAh Ni -MH ) WA RNING / AVER T ISSE MEN T : DO NOT BU RN OR PU NCTURE BATTERIES . NE PAS INCINÉRER O U PE RCER LE S P ILES. Made in China / Fa briqué en chine CR 1939 Connect the charger Charge the battery 12 hrs The battery is low and needs charging. The battery is charging. The battery is fully charged. New voicemail received from your telephone service provider. NEW There are new caller ID log entries. HANDSET NEW 10:15.pm12/25 Display After you install your telephone or power returns following a power outage and battery depletion, the handset will prompt you to set the date and time. 2 Press SELECT. 3 Enter the time. 4 Press SELECT. When the handset prompts you to set the date and time Phonebook The phonebook can store up to 30 entries, which are shared by all handsets. Each entry may consist of a telephone number up to 30 digits, and a name up to 15 characters. Add a phonebook entry 1 Enter the phone number. 2 Press MENU. 3 Press SELECT. 595-9511_ 4 Enter the name. 5 Press SELECT. Enter name Mike Smith Review phonebook entries Delete a phonebook entry Mike Smith 800-595-9511 Delete contact? 800-595-9511 1 Press DELETE. 2 Press SELECT. 1 Press . 2 Scroll to browse the entries. HANDSET 10:15pm12/25.NEW Enter number 595-9511 When your desired phonebook entry displays on the handset screen 1 set for CS6214-2/CS6214-21 1 set for CS6214/CS6214-11/ VG101/VG101-1 1 2 sets for CS6214-2/CS6214-21 Date and time Follow the steps below to set the date and time. For example, if the date is 25 December, 2019, and the time is 10:59 AM: Answer a call Make a call Technical specifications 1 Press 2 Enter the phone number - OR - Press any dialing keys to answer Press What’s in the box 1 Connect and activate 2 Setup Basic operation Phonebook Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. CAUTION: Do not install the telephone base at a height above 2 meters. 5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, nor in a wet basement or shower. 6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 7. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes. 8. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided. 9. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home or office, consult your dealer or local power company. 10. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on. 11. Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the produ…

Text truncated - open the document above for the full version.

Connect the telephone base Specifications are subject to change without notice. © 2021 VTech Communications, Inc. All rights reserved. 03/21. CS6224-X_QSG_V1.0 Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license. T Compatible with Hearing Aid T-Coil TIA-1083 The ENERGY STAR ® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR ® label indicating it meets the latest energy efficiency guidelines. Frequency control Crystal controlled PLL synthesizer Transmit frequency Handset: 1921.536-1928.448 MHz Telephone Base: 1921.536-1928.448 MHz ChannelsDECT channel: 5 Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirement Handset: 2.4V Ni-MH battery Telephone base: 6V DC @ 400mA Charger: 6V DC @ 400mA MemoryPhonebook: 30 memory locations; up to 30 digits and 15 characters Caller ID log: 30 memory locations; up to 24 digits and 15 characters If you subscribe to digital subscriber line (DSL) high-speed Internet service through your telephone line, make sure you connect a DSL filter (not included) to the telephone wall jack. Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. Quick start guide CS6224 CS6224-2 CS6224-11 CS6224-21 VG104 VG104-11 DECT 6.0 cordless telephone Quick start guide THIS SIDE UP / CE CÔTÉ VERS LE HAUT Battery Pack / Bloc-piles : BT162342/BT262342 (2.4V 300mAh Ni-MH) WA RNING / AV ERTISSEMENT : DO NOT BURN OR PUNCTURE BA TTERIES. NE PA S INCINÉRER OU PERCER LES PILES. Made in China / Fabriqué en chine CR1939 THIS SIDE UP / CE CÔ TÉ VERS LE HAUT Battery P ack / Bloc-piles : BT162342/BT262342 (2.4V 300mA h Ni -MH) WARNING / AVER TISSEME NT : DO NOT BURN O R PU NCTURE B ATT ERIES. NE PAS INCINÉRER OU PE RCE R LES PILES. Ma de i n C hina / Fabriqué en chin e CR 1939 THIS SIDE UP Install the battery THIS SIDE UP / CE CÔTÉ VERS LE HAUT Battery Pack / Bloc- piles : B T1 62342/ BT2 62342 (2.4V 3 00mAh Ni -MH) WARNING / AVE RT ISS EMENT : DO NOT BURN O R PUNCTURE BATT ERIES. NE PAS INCINÉRER OU PE RCER LE S P ILES. Ma de in Chin a / Fa briq ué en chin e CR1939 Connect the charger Charge the battery 12 hrs The battery is low and needs charging. The battery is charging. The battery is fully charged. There are new messages on the built-in answering system. New voicemail received from your telephone service provider. NEW There are new caller ID log entries. ANS ON Answering system is on. 1 The message number currently playing. HANDSET ECO NEW ANS ON 10:15pm MSG# 5/10 Display After you install your telephone or power returns following a power outage and battery depletion, the handset will prompt you to set the date and time. 2 Press SELECT. 3 Enter the time. 4 Press SELECT. When the handset prompts you to set the date and time Phonebook The phonebook can store up to 30 entries, which are shared by all handsets. Each entry may consist of a telephone number up to 30 digits, and a name up to 15 characters. Add a phonebook entry 1 Enter the phone number. 2 Press MENU. 3 Press SELECT. 4 Enter the name. 5 Press SELECT. Review phonebook entries Delete a phonebook entry 1 Press DELETE. 2 Press SELECT. 1 Press . 2 Scroll to browse the entries. When your desired phonebook entry displays on the handset screen Caller ID If you subscribe to caller ID service, information about each caller appears after the first or second ring. The caller ID log stores up to 30 entries. Each entry has up to 24 digits for the phone number and 15 characters for the name. Review caller ID log entries 1 Press . 2 Scroll to browse the entries. Dial a caller ID log entry 3 Press SELECT. 4 Edit the name if needed, then press SELECT. Save a caller ID log entry to the phonebook Delete a caller ID log entry When your desired caller ID entry displays on the handset screen When your desired caller ID entry displays on the handset screen When your desired caller ID entry displays on the handset screen Press 1 set for CS6224-2/CS6224-21 1 set for CS6224/CS6224-11/ VG104/VG104-11 2 sets for CS6224-2/CS6224-21 Date and time Follow the steps below to set the date and time. For example, if the date is 25 December, 2019, and the time is 10:59 AM: Answer a call Make a call Press DELETE to delete. Technical specifications 2 Enter the phone number - OR - Press any dialing keys to answer What’s in the box 1 Connect and activate 2 Setup Basic operation Phonebook Caller ID Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. CAUTION: Do not install the telephone base at a height above 2 meters. 5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, nor in a wet basement or shower. 6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 7. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes. 8. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product sh…

Text truncated - open the document above for the full version.

Appendix B1 Letter of Agency for FCC Certification Mar. 01, 2021 To whom it may concern, Letter of Agency I, an officer of VTech Telecommunications Limited do hereby authorize Intertek Testing Services (Mr. Ken Sit/ Mr. Melvin Nip) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Mar. 01, 2021 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 15 Certification FCC ID: EW780-2400-00 Request is hereby submitted by VTech Telecommunications Ltd. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR § 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and VTech Telecommunications Ltd. reserves the right to discern which parties can obtain access to these information:  Schematics  Detailed Block diagrams  Detailed Operational/Functional Description The rationale for request for confidentiality is as followings: This information represents intellectual property of VTech Telecommunications Ltd . and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd 21 February , 2021 To whom it may concern, Declarations FCC ID: EW780-2400-00 IC: 1135B-80240001 I, the undersigned, hereby declare that 1. The device does not use the provisions of 47CFR 15.323 (c) (6), random waiting mechanism is not used in this system. 2. The provisions of 47CFR 15.323 (c) (10) and 47CFR 15.323 (c) (11) are not used to extend the range of spectrum occupied over space or time for the purpose of denying fair access to spectrum to other devices. 3. Only the handset will act as the initiating device, which will initiate the establishment of the duplex connection. 4. The device complies with the provisions of 47CFR 15.319(f). The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude transmission of control and signaling information or use of repetitive codes used by certain digital technologies to complete frame or burst intervals. The following table explains the reaction of device in case of either absence of information to transmit or operational failure after a connection of its companion device is established. Circumstances Reaction of Handset Unit 1 Switch-off companion device NA 2 On hook by companion device NA 3 Switch-off device NA 4 On hook on device side C 5 Remove power from device C 6 Remove power from companion device A A – Connection is terminated and, transmission ceases. B – Connection is terminated but device transmits control or signaling information. C – Connection is terminated but companion device transmits control or signaling information. NA – Not applicable represents the device does not contain a hook switch or a power off switch. 5. M L of handset declared by manufacturer are 30dBm. If you have questions or need further information, please contact the undersigned. Regards, Michael Tsui Approbation Supervisor

INTERTEK TESTING SERVICES External Photos FCC ID: EW780-2400-00 IC: 1135B-80240001 INTERTEK TESTING SERVICES External Photos FCC ID: EW780-2400-00 IC: 1135B-80240001 INTERTEK TESTING SERVICES External Photos FCC ID: EW780-2400-00 IC: 1135B-80240001

CS62X4-X Engraving draft Handset Charger CS6214-2 CS6214-21 CS6224-2 CS6224-21 Model: CS6214 SN:XXXXXXXXXXXX Model: CS6214SN:XXXXXXXXXXXX Model: CS6214-11 SN:XXXXXXXXXXXX Model: CS6214-2 SN:XXXXXXXXXXXX Model: CS6214-21 SN:XXXXXXXXXXXX Model: CS6224 SN:XXXXXXXXXXXX Model: CS6224-11 SN:XXXXXXXXXXXX Model: CS6224-2 SN:XXXXXXXXXXXX Model: CS6224-21 SN:XXXXXXXXXXXX Model: VG101 SN:XXXXXXXXXXXX Model: VG101-11 SN:XXXXXXXXXXXX Model: VG104 SN:XXXXXXXXXXXX Model: VG104-11 SN:XXXXXXXXXXXX Use Only Supplied Adapter CORDLESS TELEPHONE 6V 400mA VTech Customer Service 1-800-595-9511 www.vtechphones.com SN label: 28*10 mm SN label: 20*10 mm CI BS C BS Model: CS6224 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6224-11 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6224-2 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6224-21 S/N: XXXXXXXXXXXXXXXXXXXX Model: VG104 S/N: XXXXXXXXXXXXXXXXXXXX Model: VG104-11 S/N: XXXXXXXXXXXXXXXXXXXX SN label: 28*10 mm Model: CS6214 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6214 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6214-11 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6214-2 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS6214-21 S/N: XXXXXXXXXXXXXXXXXXXX Model: VG101 S/N: XXXXXXXXXXXXXXXXXXXX Model: VG101-11 S/N: XXXXXXXXXXXXXXXXXXXX CORDLESS TELEPHONE VTECH TELECOMMUNICATIONS LTD. TEL. LINE Use Only Supplied Adapter THIS DEVIC E COMPLIES WITH PART 15 OF TH E FC C RULES. OPERATION IS SUBJE CT TO TH E FOLLOWIN G TWO CONDITION S: 1)T HIS DEVIC E MAY NOT CAUS E HARMF UL IN TER FER ENCE ; AND 2) T HIS DEVIC E MUS T ACCEPT ANY IN TER FER ENCE RECEIVED , INCL UDI NG INTER FER ENCE THAT MAY CAUSE UNDESIR ED OPERATION . PR IVACY OF C OMMUNI CATION S MAY NOT BE EN SURE D W HEN USIN G TH IS PH ONE. CORDLESS TELEPHONEMANUFACTURED IN CHINA6V 400mA HACREGISTRATION NO.:US: EW7W401A80-240000FCC ID: EW780-2400-00IC: 1135B-80240000HVIN: 35-201181BS RINGER EQUIVALENCE: 0.1AUSOC JACK: RJ11C/RJ11WCOMPLIES WITH 47 CFR PART 68 CAUTION Use Only Supplied Battery or Battery BT162342 /BT262342 FCC ID: EW780-2400-00 IC: 1135B-80240001 HVIN: 35-201634HS 6V 6V Model: CS6224 S/N: XXXXXXXXXXXXXXXXXXXX VTech Customer Service 1-800-595-9511 www.vtechphones.com VTECH TELECOMMUNICATIONS LTD. MANUFACTURED IN CHINA COMPLIES WITH 47 CFR PART 68 FCC ID: EW780-2400-00 HAC REGISTRTION NO.: US: EW7W401A80-240000 IC: 1135B-80240300 RINGER EQUIVALENCE: 0.1A USOC JACK: RJ11C/RJ11W HVIN: 35-201552BSA THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. TEL. LINE Use Only Supplied Adapter 6V 4H20 Accessory I.T.E. 4H20 I.T.E. 4H20 I.T.E.

INTERTEK TESTING SERVICES Internal photos FCC ID: EW780-2400-00 IC: 1135B-80240001 INTERTEK TESTING SERVICES Internal photos FCC ID: EW780-2400-00 IC: 1135B-80240001 INTERTEK TESTING SERVICES Internal photos FCC ID: EW780-2400-00 IC: 1135B-80240001

TEST REPORT 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 35 SPECIFIC ABSORPTION RATE (SAR) EVALUATION REPORT For DECT6.0 Cordless Telephone Model Number: CS6214-2 Brand Name: vtech FCC ID: EW780-2400-00 Prepared for VTech Telecommunications Ltd. 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong. PREPARED AND CHECKED BY: APPROVED BY: Signed On File Chan Tsz Yu, Ezra Assistant Engineer Date: Feb 10, 2021 Siu Yiu Nam, Edwin Senior Lead Engineer Date: Feb 10, 2021 TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 21020646HKG-001.doc Page 2 of 35 TABLE OF CONTENTS 1 Test Result Summary .............................................................................................................................. 3 2 General Information ............................................................................................................................... 4 3 SAR Measurement System Description ................................................................................................. 7 4 Tissue Verificaiton ................................................................................................................................ 15 5 SAR Measurement System Verification ............................................................................................... 18 6 SAR Evaluation ...................................................................................................................................... 20 7 Test Equipment List .............................................................................................................................. 30 8 Measurement Uncertainty ................................................................................................................... 31 9 E-Field Probe and Dipole Antenna Calibration .................................................................................... 31 APPENDIX A – System Check Data ........................................................................................................... 32 APPENDIX B – SAR Evaluation Data ......................................................................................................... 33 APPENDIX C – E-Field Probe and Dipole Antenna Calibration ................................................................. 34 TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 21020646HKG-001.doc Page 3 of 35 1. TEST RESULT SUMMARY The maximum spatial peak SAR value for the sample device averaged over 1g was found to be: Band Operating Mode TX Frequency (MHz) Highest Reported SAR 1 g Head 1.9GHz DECT Voice 1921.536 – 1928.448 0.0399 W/kg This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment / general population exposure limits specified in ANSI/IEEE C95.1. Applicant: VTech Telecommunications Ltd. Applicant Address: 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong. Model: CS6214-2 Brand Name: vtech Serial Number: N/A FCC ID: EW780-2400-00 Test Device: Production Unit Exposure Category: General Population/Uncontrolled Exposure Date of Test: Jan 29, 2021 Place of Testing: Intertek Testing Services Hong Kong Unit 3, G/F, World-Wide Industrial Centre, 43-47 Shan Mei Street, Fo Tan, Sha Tin. Environmental Conditions: Temperature: +18 to 25°C Humidity 25 to 75% Test Specification: ANSI/IEEE C95.1 IEEE Std 1528: 2013 FCC KDB Publication 447498 D01 v06 FCC KDB Publication 865664 D01 v01r04 FCC KDB Publication 865664 D02 v01r02 FCC KDB Publication 648474 D04 v01r03 TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 21020646HKG-001.doc Page 4 of 35 2. GENERAL INFORMATION 2.1. Description of Equipment under test (EUT) *Note: 1. DECT has a TDD/TDMA frame structure with a complete frame of 10ms duration with 24 time slots. And under these 24 time slots, the first 12 slots are allocated for the transmission from base station to handsets, and the other 12 slots are for the transmission from handsets to base station. During a call, the handset of this product will use one of 24 time slots to transmit under worst case, which gives a duty cycle of 1/24 ( = 4.2%). Manufacturer: VTech (Dongguan) Telecommunications Limited. Manufacturer Address: VTech Science Park, Xia Ling Bei Management Zone, Liaobu, Dongguan, Guangdong, China. Device dimension (L x W) : 165 (mm) x 52 (mm) Device thickness: 30 (mm) Antenna Gain: 0 dBi Operating Configuration(s) / mode: Held to head (Voice call) Tx Frequency (MHz): 1921.536MHz to 1928.448MHz Duty Cycle*: 1/24 H/W Version: N/A S/W Version: N/A Battery Type: 2.4VDC (1 x 2.4V 300mAh Ni-MH Rechargeable Battery Pack) - Model: Corun BT162…

Text truncated - open the document above for the full version.

2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 51 TEST REPORT Report Number: 21020645HKG-004 Application For Original Grant of 47 CFR Part 15 Certification New Family of RSS-213 Issue 3 Equipment Certification Unlicensed Personal Communication Service Devices/ 2 GHz License-exempt Personal Communications Service Devices (Handset) FCC ID: EW780-2400-00 IC: 1135B-80240001 Prepared and Checked by: Approved by: Signed On File Leung Chiu Kuen, Stanley Engineer Tang Kwan Mo, Jess Lead Engineer Date: March 03, 2021 TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 21020645HKG-004 Page 2 of 51 GENERAL INFORMATION Grantee: VTech Telecommunications Ltd. Grantee Address: 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong. FCC Specification Standard: FCC Part 15, October 1, 2019 Edition FCC ID: EW780-2400-00 FCC Model(s): 1. CS6214-2, CS6214, CS6214-11, CS6214-21, CS621Z-XY, VG101, VG101-11, VG101-XY 2. CS6224-2, CS6224, CS6224-11, CS6224-21, CS622Z-XY, VG104, VG104-11, VG104-XY IC Specification Standard: RSS-213 Issue 3, March 2015 RSS-Gen Issue 5, April 2018 IC: 1135B-80240001 HVIN: 35-201634HS VTech Model(s): 1. CS6214, CS6214-2, CS6214-11, CS6214-21, VG101, VG101-11 2. CS6224, CS6224-2, CS6224-11, CS6224-21, VG104, VG104-11 PMN: 1. CS6214/CS6214-2/CS6214-11/CS6214-21/VG101/VG101-11 2. CS6224/CS6224-2/CS6224-11/CS6224-21/VG104/VG104-11 Type of EUT: Unlicensed Personal Communications Service Devices Description of EUT: DECT 6.0 Cordless Telephone Serial Number: N/A Sample Receipt Date: February 10, 2021 Date of Test: February 15, 2021 to March 01, 2021 Report Date: March 03, 2021 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Conclusion: Test was conducted by client submitted sample. The submitted sample as received complied with the 47 CFR Part 15 / RSS-213 Issue 3 Certification. TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 21020645HKG-004 Page 3 of 51 TABLE OF CONTENTS 1.0 TEST RESULTS SUMMARY & STATEMENT OF COMPLIANCE ............................................ 5 1.1 Summary of Test Results ................................................................................................ 5 1.2 Statement of Compliance .............................................................................................. 6 2.0 GENERAL DESCRIPTION ................................................................................................ 7 2.1 Product Description......................................................................................................... 7 2.2 Technical Description ...................................................................................................... 7 2.3 Test Methodology ........................................................................................................... 7 2.4 Test Facility ..................................................................................................................... 7 3.0 SYSTEM TEST CONFIGURATION .................................................................................... 8 3.1 Justification ..................................................................................................................... 8 3.2 Radiated Emission Test Setup .......................................................…

Text truncated - open the document above for the full version.