EW780-2409-00DECT 6.0 cordless phone

DECT 6.0 2-line corded/cordless telephone with BLUETOOTH® wireless technology Scan the QR code for support information Quick start guide IS9141 IS9141-2 IS9141-3 IS9141-4 IS9141-5 USCA a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment containing concentrations of flammable or flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a fire or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc. 17. Only put the handset of your telephone next to your ear when it is in normal talk mode. 18. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 19. For pluggable equipment, the socket- outlet shall be installed near the equipment and shall be easily accessible. 20. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the handset. Use only the supplied rechargeable batteries or replacement batteries (BT162342/BT262342) for the handset. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the instruction. • Do not use the battery in following conditions: • High or low extreme temperature during use, storage or transportation. • Replacement of a battery with an incorrect type that can defeat a safeguard. • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. • A battery subjected to extremely low air pressure that can result in an explosion or the leakage of flammable liquid or gas. 21. Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously damage the product. 22. The applied nameplate is located at the bottom or near of the product. SAVE THESE INSTRUCTIONS Battery • Use only the batteries provided or equivalent. To order a replacement, visit our website at www.vtechphones. com or call 1 (800) 595-9511. In Canada, go to phones.vtechcanada.com or call 1 (800) 267-7377. • Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions. • Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed. • Exercise care in handling batteries in order not to create a short circuit with conductive materials. • Charge the battery provided with this product only in accordance with the instructions and limitations specified in this manual. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. CAUTION: Do not install the telephone base at a height above 2 meters. 5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, or in a wet basement or shower. 6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 7. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes. 8. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided. 9. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home or office, consult your dealer or local power company. 10. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on. 11. Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 12. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 13. Do not overload wall outlets and extension cords. 14. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: • When the power supply cord or plug is damaged or frayed. • If liquid has been spilled onto the product. • If the product has been exposed to rain or water. •…

Text truncated - open the document above for the full version.

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax:(852)2680 5252 E-mail: [email protected] CFR 47 §2.911(d)(5)(i) Attestation Letter Attestation Letter Date: 2023-2-15 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: EW780-2409-00 VTech Telecommunications Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature: Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax:(852)2680 5252 E-mail: [email protected] CFR 47 §2.911 (d)(5)(ii) Attestation Letter Attestation Letter Date: 2023-2-15 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID:EW780-2409-00 VTech Telecommunications Ltd certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature: Michael Tsui Approbation Supervisor

U.S. AGENT LETTER OF ATTESTATION Date: 2023-02-22 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing VTech Telecommunications Ltd certifies that, as of the date of the filing of the application, VTech Communications, Inc. is our designated U.S. agent for service of process for the FCC ID. VTech Telecommunications Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. VTech Communications, Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the FCC ID. Designated U.S. Agent Information: Company Name: VTech Communications, Inc. Address: 9020 SW Washington Square Road, Tigard OR 97223 Agent FRN : 0033411265 Tel.: +1(503) 596-1212 Email: [email protected] Signed by: Chris Conrad Signature: Applicant Company Name: VTech Telecommunications Ltd Address: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Applicant FRN: 0015973951 Tel: (852)2680 5398 Email: [email protected] Signed by: Michael Tsui Signature:

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: [email protected] QA-FR-170-B FCC Authorization Date: 2023-01-18 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, VTech Telecommunications Ltd, the undersigned, Hereby authorizes Shenzhen Accurate Technology Co., Ltd.to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: [email protected] FCC Confidential Authorization Date: 2023-01-18 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: EW780-2409-00 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, VTech Telecommunications Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Jan. 06, 2023 To whom it may concern, FCC-Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows: Electrical designs, including software & firmware PCB layout Construction design/Physical design/Enclosure Others, please specify The only differences between these models are the follows for marketing purpose: Color Cosmetic details Trade name Model number Others, please specify Package type, no. of Handset and Charger. Suffix ( “X,Y, Z”) represents Color code Packing configuration Others, please specify Z= any alphanumeric character is presenting different package type (material). X= any alphanumeric character or blank is presenting number of Handset and extra Charger. Y= any alphanumeric character or blank is presenting different color of enclosure. ,but models with suffix ( X,Y,Z ) are identical in: Electrical designs, including software & firmware PCB layout Construction design/Physical design/Enclosure Others, please specify Package type, no. of Handset and Charger. For the product subject to authorization under FCC Declaration of Conformity: In addition, it is to confirm that all the below information 1) The U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual Are the same but different in the following model numbers only: Item # New Model Model Number Trade Name Remarks 1 YES IS9141 vtech 1 base + 1 handset 2 YES IS9141-2 vtech 1 base + 2 handsets + 1 charger 3 YES IS9141-3 vtech 1 base + 3 handsets + 2 chargers 4 YES IS9141-4 vtech 1 base + 4 handsets + 3 chargers 5 YES IS9141-5 vtech 1 base + 5 handsets + 4 chargers 6 YES IS914Z-XY vtech 1 base + X handsets + (X-1) chargers 7 YES IS9101 vtech 1 handset + 1 charger 8 YES IS910Z-XY vtech 1 handset + 1 charger The sample(s) being submitted to Shenzhen Accurate Technology Co., Ltd. for conformity assessment is IS9141-2 of the above list. vtech 1 handset + 1 charger VTech Telecommunications Ltd All above model's FCC ID: EW780-2409-00 Regards, Michael Tsui Approbation Supervisor

Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 1 of 13 External Photos Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 2 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 3 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 4 of 13 Charger Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 5 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 6 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 7 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 8 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 9 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 10 of 13 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 11 of 13 Model: IS9101 Model: IS9141 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 12 of 13 Model: IS9141-2 Model: IS9141-3 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF External Photos Page 13 of 13 Model: IS9141-4 Model: IS9141-5

Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF LABEL AND LOCATION Page 1 of 2 FCC ID Label Label 1 Label 2 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF LABEL AND LOCATION Page 2 of 2 FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Label 2 Label 1

Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Internal Photos Page 1 of 6 Internal photos Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Internal Photos Page 2 of 6 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Internal Photos Page 3 of 6 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Internal Photos Page 4 of 6 ANT Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Internal Photos Page 5 of 6 Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Internal Photos Page 6 of 6 Charger

Shenzhen Accurate Technology Co., Ltd. Project No.: RA1221201-58517E-SA Page 1 of 3 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm Phantom Type: Twin SAM Phantom ; Type: QD000 P40 CD; Serial: TP:1744 Head Left Cheek Setup Photo Shenzhen Accurate Technology Co., Ltd. Project No.: RA1221201-58517E-SA Page 2 of 3 Head Left Tilt Setup Photo Head Right Cheek Setup Photo Shenzhen Accurate Technology Co., Ltd. Project No.: RA1221201-58517E-SA Page 3 of 3 Head Right Tilt Setup Photo Body Back Setup Photo (0mm)

★ Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “ ”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 821: 2021-11-09 Page 1 of 51 FCC SAR TEST REPORT Applicant Name : VTech Telecommunications Ltd Address : 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Report Number : RA1221201-58517E-SAA FCC ID: EW780-2409-00 Test Standard (s) FCC 47 CFR part 2.1093 Sample Description Product Type: DECT 6.0 cordless phone Model No.: IS9141-2 Multiple Model(s) No.: IS9141, IS9141-3, IS9141-4, IS9141-5, IS914Z-XY, IS9101, IS910Z-XY(Please refer to DOS for Model difference) Trade Mark: vtech Date Received: 2022/12/05 Report Date: 2022/12/12 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Lance Li Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: RA1221201-58517E-SAA Version 821: 2021-11-09 Page 2 of 51 FCC SAR Attestation of Test Results MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) DECT 1g Head SAR 0.04 1.6 1g Body SAR 0.03 Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices RF Exposure Procedures: TCB Workshop April 2019 IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-1:2016 Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 648474 D04 Handset SAR v01r03. KDB 865664 D01 SAR measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Shenzhen Accurate Technology Co., Ltd. Report No.: RA1221201-58517E-SAA Version 821: 2021-11-09 Page 3 of 51 FCC SAR TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION ................................................................................................................................................... 5 TECHNICAL SPECIFICATION ............................................................................................................................................. 5 REFERENCE, STANDARDS, AND GUIDELINES ................................................................................................. 6 SAR LIMITS ..................................................................................................................................................................... 7 FACILITIES ................................................................................................................................................................. 8 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 9 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 15 EQUIPMENTS LIST & CALIBRATION INFORMATION ........................................................................................................ 15 SAR MEASUREMENT SYSTEM VERIFICATION ............................................................................................. 16 LIQUID VERIFICATION ................................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION ............................................................................................................................... 17 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 19 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR ........................................................................... 19 CHEEK/TOUCH POSITION ............................................................................................................................................... 20 EAR/TILT POSITION ....................................................................................................................................................... 20 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS .................................................................................. 21 TEST DISTANCE FOR SAR EVALUATION …

Text truncated - open the document above for the full version.

Model: IS9141 HSAntenna description:This Printed F antenna is optimized and used in the Handset unit. This antenna is directly soldered to the ANT RF output in the main PCB. IS9141 HS Antenna Dimensions in mm 31.4 mm 11.5 mm Frequency: 1924.992 MHZ (the frequency with maximum gain) Vertical Horizontal 0.00 -2.60 Antenna Gain (dBi) IS9141 HS Radiation Pattern_XY Plane -25-20-15-10 -5 05 VerticalHorizontal Model: IS9141 BS ANT0Antenna description:This monopole antenna is optimized and used in the Base unit. This antenna is directly soldered to the ANT0 RF output in the main PCB. Frequency: 1924.992 MHZ (the frequency with maximum gain) Vertical Horizontal -3.30 0.00 Antenna Gain (dBi) IS9141 BS ANT0 Radiation Pattern_XY Plane -35-30-25-20-15-10 -5 05 VerticalHorizontal IS9141 BS ANT0 Dimensions in mm: Model: IS9141 BS ANT1Antenna description:This monopole antenna is optimized and used in the Base unit. This antenna is directly soldered to the ANT1 RF output in the main PCB. Frequency: 1924.992 MHZ (the frequency with maximum gain) Vertical Horizontal 0.00 -6.91 Antenna Gain (dBi) IS9141 BS ANT1 Radiation Pattern_XY Plane -30-25-20-15-10 -5 05 VerticalHorizontal IS9141 BS ANT1 Dimensions in mm Model: IS9141 BS BT ANTAntenna description:This monopole antenna is optimized and used in the Base unit. This antenna is directly soldered to the BT ANT RF output in the main PCB. Frequency: 2475 MHZ (the frequency with maximum gain) Vertical Horizontal -4.16 0.00 Antenna Gain (dBi) IS9141 BS BT ANT Radiation Pattern_XY Plane -30-25-20-15-10 -5 05 VerticalHorizontal IS9141 BS BT Antenna Dimensions in mm

Note: This report may contain dat ★ a that are not covered by the A2LA accreditation and are marked with an asterisk “ ”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 52: 2021-11-09 Page 1 of 63 FCC-RF；RSS-RF TEST REPORT Applicant Name : FCC: VTech Telecommunications Ltd ISEDC: VTECH TELECOMMUNICATIONS LIMITED Address : FCC: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong ISEDC: BL.1 23/F Tai Ping Industr Ctr. 57 Ting Kok Road Tai Po, NT Hongkong Report Number : RA221201-58517E-RFB FCC ID: EW780-2409-00 IC: 1135B-80240901 Test Standard (s) FCC PART 15D; RSS-GEN ISSUE 5, FEBRUARY 2021 AMENDMENT 2; RSS-213, ISSUE 3, MARCH 2015 Sample Description Product Type: DECT 6.0 cordless phone Model No.: IS9141-2 Multiple Model(s) No.: FCC: IS9141, IS9141-3, IS9141-4, IS9141-5, IS914Z-XY, IS9101, IS910Z-XY IC: IS9141, IS9141-3, IS9141-4, IS9141-5,IS9101 Trade Mark: vtech Date Received: 2022/12/01 Report Date: 2023/02/06 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Andy Yu Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: RA221201-58517E-RFB Version 52: 2021-11-09 Page 2 of 63 FCC-RF；RSS-RF TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 GENERAL INFORMATION ....................................................................................................................................... 5 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 5 OBJECTIVE ................................................................................................................................................................... 5 TEST METHODOLOGY .................................................................................................................................................. 6 MEASUREMENT UNCERTAINTY .................................................................................................................................... 6 TEST FACILITY ............................................................................................................................................................. 6 SYSTEM TEST CONFIGURATION .......................................................................................................................... 7 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 7 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 7 EXTERNAL I/O CABLE .................................................................................................................................................. 7 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULTS ............................................................................................................................... 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC §1.1307 & §2.1093 - RF EXPOSURE ................................................................................................................ 11 APPLICABLE STANDARD ............................................................................................................................................ 11 TEST RESULT ............................................................................................................................................................. 11 RSS-102 – RF EXPOSURE ......................................................................................................................................... 12 APPLICABLE STANDARD ............................................................................................................................................ 12 § 15.317, § 15.203 & RSS-GEN §6.8 ANTENNA REQUIREMENT ....................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 13 § 15.323 (A) & RSS-213 §5.5 EMISSION BANDWIDTH ........................................................................................ 14 APPLICABLE STANDARD ................................................................................................................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. Project No.: RA221201-58517E-RF Test Photos Page 1 of 1 Photo of Radiated Emission Measurement (Below 1G) Photo of Radiated Emission Measurement (Above 1G)