EW780-2580-00Video Monitor - Baby Unit

Privacy Mode Cable management What’s in the box Connect and Power On the Camera x 2 x 2 Quick start guide Your baby monitor package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Designed for extra peace of mind, turn on Privacy Mode for a moment of peace and quiet. When the Privacy Mode is turned on, audio transmission and video monitoring will be disabled so motion recording, motion detection, and sound detection will be temporarily unavailable. Connect the power adapter to the camera and a power supply, then the camera powers on automatically. Overview Camera 1Bee cover 2Light sensor 3Camera lens 4Microphone 5Night Light 6Speaker 7Status LED 8PAIR • Press and hold for three seconds to enter pairing mode. • Reset the baby unit to factory default. 1. Press and hold PAIR key until you hear a beep sound. 2. Release the PAIR key, and then press the PAIR key again five times until you hear another beep sound. 3. The baby unit will sound another beep when the reset completes. Then, the baby unit will reboot. 9Temperature sensor 10Power jack 11Wall mount slots 4 5 6 7 8 9 10 11 3 2 1 4 5 6 7 8 9 10 11 3 2 1 4 5 6 7 8 9 10 11 3 2 1 • Use only the power adapter supplied with this product. • If the camera is connected to a switch controlled electric outlet, make sure the switch is on. • Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed to hold the weight of the camera, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. • To maintain compliance with the FCC’s RF exposure guidelines, place the camera at least 20cm from nearby persons. 1 set for RM9751 Important safety instructions After installing the Baby Care App... • Sign up for an account • Pair the camera with your mobile device • Monitor your baby using a wide range of features Start monitoring from anywhere. Download the free MyVTech Baby Pro mobile app and install it to a mobile device, then use your mobile device and the mobile app to monitor your areas remotely. Download app for mobile access Pair the Camera with your Mobile Device App Compatibility • Android TM 6.0 or later • iOS 12 or later. On Baby Care App Before you start... • Connect your mobile device to a 2.4GHz Wi-Fi network for a better connection and smoother video streaming. • Enable the Location Service of your mobile device for the purpose of camera setup. With a 2.4GHz Wi-Fi network and enabled Location Service... You can start to pair the camera with your own mobile device following the instructions in the app. Upon the successful pairing, you can hear and watch your baby via your mobile device. Tips: • Move the camera and the Wi-Fi router closer to each other in order to strengthen the network signal. • It takes up around 1 minute to search the camera. The applied nameplate is located at the bottom of the camera’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the camera at a height above 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Power adapters information: Camera Output: 5V 1A; VTech Telecommunications Ltd.; Model: VT05EUS05100 7. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under- the-table or cabinet outlet. 8. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 9. Unplug this product from the wall outlet before cleaning. 10. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 11. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 12. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 13. Do not overload wall outlets or use an extension cord. 14. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 15. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 16. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 17. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose…

Text truncated - open the document above for the full version.

vtech Attention: Application Examiner Re: Covered List, located at https://www.fcc.2:ov/supplychain/coveredlist and Report & Order 22-84 located at https://docs.fcc.gov/public/attachments/DOC-389524A l .pdf Applicant: VTech Telecommunications Ltd. FCC ID: EW780-2580-00 To whom it may concern, Pursuant to FCC Report & Order 22-84 section IV. Interim Freere Order, paragraphs 264, 265, and 266, as an authorired representative ofVTech Telecommunications Ltd., I attest that the equipment for which we are seeking equipment authorization through certification is not prohibited from receiving an equipment authorization; and VTech Telecommunications Ltd . is not an entity identified on the Covered List or an affiliate or subsidiary of an entity identified on the Covered List, established pursuant to 47 CFR§1.50002. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the company and agree to immediately notify Intertek if there is any change in the status identified above. 芸三 n, Ltd Form: RFT-AMER-TCB-OP-19m Date: 21 December 2022 Revision: 1 Page 1 of 1

VTech Telecommunications Ltd Appendix B1 Letter of Agency for FCC Certification Sep. 27, 2017 To whom it may concern, Letter of Agency I, an officer of VTech Telecommunications Ltd do hereby authorize Intertek Testing Services (Terry Chan/ Koo Wai Ip/ Kenneth Wong/ Jess Tang) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Jun 2, 2022 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 15 Certification FCC ID: EW780-2580-00 Request is hereby submitted by VTech Telecommunications Ltd. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR § 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and VTech Telecommunications Ltd. reserves the right to discern which parties can obtain access to these information: • Schematics • Detailed Block diagrams • Detailed Operational/Functional Description The rationale for request for confidentiality is as followings: This information represents intellectual property of VTech Telecommunications Ltd . and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards, Michael Tsui Approbation Supervisor

INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (External) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (External)

27.1 22.3 3.0 BU Label 26.7x21.7mm A/V I.C.T.E. HVIN: 35-400373BU MANUFACTURED IN CHINA FCC ID: EW80-2580-00 IC: 1135B-80258000 Model: RM9751 S/N: XXXXXXXXXXX 5V 1A WIFI MAC: XXXXXX A/V I.C.T.E. HVIN: 35-400373BU MANUFACTURED IN CHINA FCC ID: EW80-2580-00 IC: 1135B-80258000 Model: RM9751 S/N: XXXXXXXXXXX 5V 1A WIFI MAC: XXXXXX 27.1 22.3 3.0 BU Label 26.7x21.7mm A/V I.C.T.E. HVIN: 35-400373BU MANUFACTURED IN CHINA FCC ID: EW80-2580-00 IC: 1135B-80258000 Model: RM2771 BU S/N: XXXXXXXXXXX 5V 1A WIFI MAC: XXXXXX A/V I.C.T.E. HVIN: 35-400373BU MANUFACTURED IN CHINA FCC ID: EW80-2580-00 IC: 1135B-80258000 Model: RM2771-2 BU S/N: XXXXXXXXXXX 5V 1A WIFI MAC: XXXXXX A/V I.C.T.E. HVIN: 35-400373BU MANUFACTURED IN CHINA FCC ID: EW80-2580-00 IC: 1135B-80258000 Model: RM2771 BU S/N: XXXXXXXXXXX 5V 1A WIFI MAC: XXXXXX

INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal) INTERTEK TESTING SERVICE Report No.: HK22051514 Equipment Photographs RM9751 (Internal)

INTERTEK TESTING SERVICE FCC ID: EW780-2580-00 MPE Analysis Report The Equipment-Under-Test (EUT) is a Video Monitor - Baby Unit. It has a microcontroller and 2.4GHz RF module. The EUT is powered by a 5V AC/DC adaptor. For Maximum Permissible Exposure (MPE) evaluation of the unit, the maximum power density at 20 cm from this transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65 and meet the requirement listed in KDB447498. For the 2.4GHz RF portion of the unit, the measured powers among all the measured channels were within its production tolerance. The antenna gain is 0 dBi = 1 (num gain) and its maximum source-based time-averaging duty factor is 100%. From these data and its operating configuration, the exposed power density at a distance (R) of 20 cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The EIRP radiated power = conducted power (with maximum tolerance) + antenna gain = 17 dBm + 0 dBi = 17 dBm (50 mW) The radiated (EIRP) source-based time-averaging output power = (50 * 1) mW = 50 mW The power density at 20 cm from the antenna = EIRP / 4 πR^2 = 0.01 mW cm-2 In the frequency range of 1,500 - 100,000MHz, the MPE limit is 1.0 mWcm-2 for general population and uncontrolled exposure. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the Baby unit at least 20cm from nearby persons.”

2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 96 TEST REPORT Report Number: 22051514HKG-001 Application for Original Grant of 47 CFR Part 15 Certification New Family of RSS-247 Issue 2 Equipment FCC ID: EW780-2580-00 IC: 1135B-80258000 Prepared and Checked by: Approved by: Signed On File Wong Cheuk Ho, Herbert Lead Engineer Wong Kwok Yeung, Kenneth Assistant Supervisor Date: June 30, 2022 TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 22051514HKG-001 Page 2 of 96 GENERAL INFORMATION Applicant Name: VTech Telecommunications Ltd. Applicant Address: 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong. FCC Specification Standard: FCC Part 15, October 1, 2021 Edition FCC ID: EW780-2580-00 FCC Model(s): RM9751, RM2771 BU, RM2771-2 BU IC Specification Standard: RSS-247 Issue 2, February 2017 RSS-Gen Issue 5 Amendment 2, February 2021 IC: 1135B-80258000 PMN: RM9751, RM2771 BU, RM2771-2 BU HVIN: 35-400373BU Vtech Model(s): RM9751, RM2771 BU, RM2771-2 BU Type of EUT: Spread Spectrum Transmitter Description of EUT: Video Monitor - Baby Unit Sample Receipt Date: May 30, 2022 Date of Test: May 30, 2022 to June 23, 2022 Report Date: June 30, 2022 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Conclusion: Test was conducted by client submitted sample. The submitted sample as received complied with the 47 CFR Part 15 / RSS-247 Issue 2 Certification. TEST REPORT VTech Telecommunications Ltd. Intertek Report No: 22051514HKG-001 Page 3 of 96 TABLE OF CONTENTS 1.0 TEST RESULTS SUMMARY & STATEMENT OF COMPLIANCE ............................................ 4 1.1 Summary of Test Results ................................................................................................. 4 1.2 Statement of Compliance ................................................................................................ 4 2.0 GENERAL DESCRIPTION ................................................................................................ 5 2.1 Product Description ....................................................................................................... 5 2.2 Test Methodology ........................................................................................................... 6 2.3 Test Facility ..................................................................................................................... 6 2.4 Related Submittal(s) Grants ............................................................................................ 6 3.0 SYSTEM TEST CONFIGURATION .................................................................................... 7 3.1 Justification ..................................................................................................................... 7 3.2 EUT Exercising Software .................................................................................................. 8 3.3 Details of EUT and Description of Accessories ................................................................. 9 3.4 Measurement Uncertainty .............................................................................................. 9 4.0 TEST RESULTS ............................................................................................................ 10 4.1 Maximum Conducted Output Power at Antenna Terminals ......................................... 10 4.2 Minimum 6dB RF Bandwidth......................................................................................... 18 4.3 Maximum Power Spectral Density ................................................................................ 28 4.4 Out of Band Conducted Emissions ................................................................................ 38 4.5 Field Strength Calculation.............................................................................................. 78 4.6 Transmitter Radiated Emissions in Restricted Bands and Spurious Emissions ............... 79 4.6.1 Radiated Emission Configuration Photograph ............................................................ 79 4.6.2 Radiated Emission Data .............................................................................................. 79 4.6.3 Radiated Emission Test Setup ..................................................................................... 90 4.6.4 Transmitter Duty Cycle Calculation ............................................................................ 91 4.7 AC Power Line Conducted Emission .............................................................................. 92 4.7.1 AC Power Line Conducted Emission Configuration Photograph ................................. 92 4.7.2 AC Power Line Conducted Emission Data ..........…

Text truncated - open the document above for the full version.

[VTECH] [2.4GHz Antenna] Model: RM 9751 BU Antenna description: This antenna is optimized and used in the Baby Unit in the baby monitor models. This antenna is directly soldered to the RF output in the main PCB. Ordering information: Model Description RM 9751 BU 2.4GHz Antenna Specification: Operation Frequency Range 2412-2472 MHz Maximum Gain 0 dBi Type PCB dipole Operation bandwidth 60MHz Nominal Impedance ~50 ohms Connectors - Dimensions 26 x 13mm Manufacturer Vtech Telecommunications Ltd Manufacturer address 23/F, Tai Ping Industrial Centre, Blk1, 57 Ting Kok Road, Tai Po, Hong Kong Model number ANT-RM9751-F-WI-1 [VTECH] [2.4GHz Antenna] Antenna pattern (2436MHz) (the frequency with maximum gain) XY plane (gain theta) [VTECH] [2.4GHz Antenna] Coordination: Physical Dimension: Figure 1 Physical dimension (mm)

INTERTEK TESTING SERVICE Report No: HK22051514 Configuration Photographs Worst-Case Radiated Emissions (Front View) INTERTEK TESTING SERVICE Report No: HK22051514 Configuration Photographs Worst-Case Radiated Emissions (Rear View) INTERTEK TESTING SERVICE Report No: HK22051514 Configuration Photographs Worst-Case Radiated Emissions (Front View) INTERTEK TESTING SERVICE Report No: HK22051514 Configuration Photographs Worst-Case Radiated Emissions (Rear View)

INTERTEK TESTING SERVICE Report No: HK21051514 i Configuration Photographs Worst-Case Line-Conducted Emissions (Front View) INTERTEK TESTING SERVICE Report No: HK21051514 ii Configuration Photographs Worst-Case Line-Conducted Emissions (Rear View) INTERTEK TESTING SERVICE Report No: HK21051514 iii Configuration Photographs Worst-Case Line-Conducted Emissions (Side View)