EW780-5198-01VTECH 5831 Handset

1 When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1.Read and understand all instructions. 2.Follow all warnings and instructions marked on the product. 3.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4.Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). 5.Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6.Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided. 7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. 9.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10.To reduce the risk of electric shock, do not disassemble this product. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassemb-ling can cause electric shock when the appliance is subsequently used. 11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. Important Safety Instructions 2 12.Unplug this product from the wall outlet and refer servicing to VTECH under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. 13.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 14.Do not use the telephone to report a gas leak in the vicinity of the leak. VTECH COMMUNICATIONS INC. CUSTOMER SERVICE at 1-800-595-9511. In Canada, call VTech Electronics Ltd. at 1-800-267-7377. SAVE THESE INSTRUCTIONS 3 The VT5831 is an advanced cordless telephone that operates in the 5.8GHz frequency range. Your VT5831 is capable of supporting up to a maximum of 6 Handsets. Using additional Handsets, up to three people can be conferenced on a call (2 Handsets and the Base Speakerphone), or two extensions can be conferenced on a call, while two other extensions can be talking internally, using the Intercom feature. This manual is designed to familiarize you with the VT5831 cordless telephone. We strongly recommend you read the manual before using your phone. To order additional system Handsets (model# VT 5820), battery packs, or headsets, call VTech Communications Inc at 1-800-595- 9511. Introduction IMPORTANT Please record the Base ID#(BS ID) printed on the underside of the 5831 Base in the space below. Please be certain to include all 15 digits/characters. Base ID # 4 Parts Check List 7. Belt clip 8.Base Wall Mounting Bracket 9.Charger Wall Mounting Bracket 10.Owner's Manual 11. Battery Pack To purchase replacement battery packs, call VTech Communications Inc. at 1-800-595-9511. In Canada, call VTech Electronics Ltd. at 1-800-267-7377. 1.Base Unit 2.Handset 3.Charger AC Power Adapter 4. Charger 5. Base AC Power ADapter 6. Telephone Cord
                    !  "         #  "  Chargser AC Power Adapter Chargser 5 The Handset Layout 1.Antenna 2.Earpiece 3.Headset Jack (2.5mm) 4.On (Flash) 5.Dialing Key(0-9) 6.Speaker Phone 7.LCD Display 8.Soft keys 9.Volume key 10.Off (Clear) 11.Sound Select key 12.Microphone 1 2 3 4 5 6 7 8 11 12 9 10 6 1.Antenna 2.LCD Display 3.Clear 4.In use 5.Flash 6.Hold 7.Redial 8.Mute 9.Messages 10.Intercom 11. Soft keys 12.Speaker Phone 13.Dialing Keys (0-9) 14.Volume Keys 15.Telephone Jack 16.DC Connector 17.Spare Battery drawer 18.Spare Battery Release The Base Unit Layout 1 2 3 4 6 7 8 5 9 10 11 12 13 14 17 18 16 15 7 Setup 1.Plug the AC power adapter into an electrical outlet, and the DC connector into the back of the base unit. Connecting to phone line Plug one end of the telephone line cord into the jack on the back of the base unit. Plug the other end of this cord into the wall jack. Checking for dial tone After the battery is charged press ON on the Handset. The Phone icon will appear on the handset display, and you will hear dial tone. If not, see In Case of Difficulty. Tone/Pulse selection See BASE SETTINGS for details. CAUTION: Use only the Vtech power supply provided with your telephone. Getting Started IMPORTANT: FOR MAXIMUM PERFORMANCE OF YOUR CORDLESS TELEPHONE SYSTEM: 1. Choose a central location for your Base Unit. 2. Install your Base Unit and Extension Handsets away from electronic equipment, such as personal computers, television sets and microwave ovens. 3. In locat…

Text truncated - open the document above for the full version.

TECH V ENGINEERING CANADA LTD. 200-7671 Alderbridge Way, Richmond B.C. Canada V6X 1Z9 FAX: (604) 276-9137 TEL: (604) 273-5131 FCC ID: EW780-5198-00 EW780-5198-01 Federal Communications Commission 7435 Oakland Mills Road, Columbia, Maryland 21046 Authority To Act As Agent To The Federal Communication Commissions I appoint Nemko Canada Inc. to act as agent in the preparation of applications for equipment authorization on our behalf to the Federal Communications Commission. I certify that exhibits submitted properly describe the devise or system for which equipment authorization is sought. I also certify that each unit manufactured, imported or marketed, as defined in the commissions regulations will have affixed to it a label identical to that submitted for approval with this application. Dated this __20th _day of ___March__ 2002 Agency Agreement Expiration Date: Sept. 30, 2002 By:_ _Joseph Poon (Signature)(Printed) Title: Regulatory Compliance Manager Telephone: (604) 273-5131 Applicant: VTECH Engineering Canada Ltd.

TECH V ENGINEERING CANADA LTD. 200-7671 Alderbridge Way, Richmond B.C. Canada V6X 1Z9 FAX: (604) 276-9137 TEL: (604) 273-5131 FCC ID: EW780-5198-00 EW780-5198-01 Federal Communications Commission 7435 Oakland Mills Road, Columbia, Maryland 21046 Request for Confidentiality VTech Telecommunications Ltd. would like to keep the following documents as confidential for the application of the VTech 5831 approval for FCC Part 15 submission. (1) Schematics (2) Technical description -- file name :5.8 rf theory rev4.doc 5.8 system description.doc The above documents contain information for new technology & ideas in 2.4GHz / 5.8GHz cordless telephone, so we would like to prevent the use of this information by other companies. Dated this __20th__day of ____March__ 2002 By:_ _Joseph Poon (Signature)(Printed) Title: Regulatory Compliance Manager Telephone: (604) 273-5131 Applicant: VTECH Engineering Canada Ltd.

Bay Area Compliance Laboratory Corp. 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732 9162 Fax: (408) 732 9164 Federal Communications Commission 7435 Oaklands Mills Road – Gate A Columbia, Maryland, 21046 June 12, 2002 Ref: FCC Question on VTech R0203182 SAR Report This letter aims to reply your questions to the above mentioned report. Q1. SAR test was done with 1800 MHz head liquid and probe factor for 2400MHz head and body. This SAR report is not applicable to demonstrate 2400 MHz SAR compliance. SAR values are low, and Supplement C Table 1 applies. Some comments on SAR report are as follows. A1. SAR test was done with 1800 MHz and the probe factor was for 1800 MHz also. Please see Page 19, 20 and 23 of the revised test report. Q2. FYI. In future filings please include test date on printouts from DASY system. A2. We will include test data on printout from DASY system in the future. Q3. Please demonstrate that frequency hopping was disabled during SAR test. A3. Please see page 47, 48, and 49 of the revised test report. Q4. SAR plots list SAM phantom, but setup photos show Generic Twin phantom. Please clarify which phantom was used. A4. It was Generic Twin phantom. Q5. Please submit data pages from probe cal cert. A5. The data page from probe calibration certificate was added to Page 45 of the revised test report. Yours truly, John Chan Engineering Manager

30-0930 hs frt 30-0940 battery drawer x 30-0949 charger Btm 30-0929 hs rear 30-0931 bs btm 3 2 5 6 7 4 TEL LINE 1 FCC ID: EW780-5198-01 TEL LINE 2 7 30-0930 hs frt FCC ID: EW780-5198-01 30-0931 bs btm VTECH TELECOMMUNICATIONS LTD. DC 7V 900mA CLASS 2 POWER SOURCE ONLY CORDLESS TELEPHONE 4 40.0mm 21.0mm MODEL: 5831 VTECH TELECOMMUNICATIONS LTD. MANUFACTURED IN CHINA COMPLIES WITH 47 CFR PART 68 REGISTRATION NO.: US: EW7 WIXXB80-5198-00 RINGER EQUIVALENCE: X.XB USOC JACK: RJ11C, RJ11W THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. HAC FCC ID: EW780-5198-00 CANADA XXXX XXX XXXXX REN/IES: 0.0 IC: RSS/CNR210 3 70.0mm 29.5 mm 30-0940 battery drawer 6 CAUTION: Danger of explosion if battery is incorrectly replaced. USE ONLY BATTERY 80-5017-00-00 42.0mm 14.2 mm 5 30-0949 charger Btm VTECH TELECOMMUNICATIONS LTD. DC 6V 300mA CLASS 2 POWER SOURCE ONLY CORDLESS TELEPHONE 15.5mm 40.5mm 30-0929 hs rear CAUTION: Danger of explosion if battery is incorrectly replaced. USE ONLY BATTERY 80-5017-00-00 1 24.0mm 13.0mm 19.0mm 3.0 mm

Note: This test report is specially limited to the above client company and the product model only. It may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. SAR EVALUATION REPORT For VTech Telecommunications Ltd. 23/F Tai Ping Industrial Center Block 1 57 Ting Kok Road, Tai Po NT, Hong Kong Model: VT 5831 April 1, 2002 This Report Concerns: Original Report Equipment Type: Cordless Phone Test Engineer: John Chan Report No.: R0203182 Test Date: March 31, 2002 Certified By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732-9162 Fax: (408) 732 9164 VTech Telecommunications Ltd. Model: VT 5831 Report #R0203182 FCC SAR Evaluation Report Page 2 of 46 CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Applicant: VTech Telecommunications Ltd. 23/F Tai Ping Industrial Center Block 1 57 Ting Kok Road, Tai Po NT, Hong Kong Trade Name: N/A Model: 2.4GHz Cordless Phone Handset Serial Number: N/A FCC ID: EW780-5198-01 Dates of Tests: March 31, 2002 Report No: R0203182 Tx Frequency: 2401.056 ~ 2482.272 MHz Max. RF Output Power: 22.2dBm (0.166Watt) RF Exposure environment: General Population/Uncontrolled Application Type: Certification FCC Rule Part(s): FCC 15.247 This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. John Chan Engineering Manager VTech Telecommunications Ltd. Model: VT 5831 Report #R0203182 FCC SAR Evaluation Report Page 3 of 46 TABLE OF CONTENTS CERTIFICATE OF COMPLIANCE (SAR EVALUATION) ...................................................................................2 1 - EUT DESCRIPTION ...............................................................................................................................................4 2 - REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC...............................................5 3 - DOSIMETRIC ASSESSMENT SETUP.................................................................................................................6 3.1 MEASUREMENT SYSTEM DIAGRAM.......................................................................................................................7 3.2. SYSTEM COMPONENTS..........................................................................................................................................8 3.3. EUT ARRANGEMENT..........................................................................................................................................12 3.4 MEASUREMENT UNCERTAINTY............................................................................................................................17 4 - EUT TUNE-UP PROCEDURE.............................................................................................................................18 5 - EVALUATION PROCEDURE.............................................................................................................................19 5.1 SIMULATED TISSUE LIQUID PARAMETER CONFIRMATION...................................................................................19 5.2 SYSTEM ACCURACY VERIFICATION.....................................................................................................................19 5.3 SAR EVALUATION PROCEDURE...........................................................................................................................21 5.4 EXPOSURE LIMITS................................................................................................................................................22 6 - TEST RESULTS ....................................................................................................................................................23 6.1 LEFT HEAD CONFIGURATION...............................................................................................................................23 6.2 RIGHT HEAD CONFIGURATION.............................................................................................................................23 6.3 BODY WORN CONFIGURATION............................................................................................................................23 6.4 LIQUID MEASUREMENT RESULT..........................................................................................................................23 7 - REFERENCE .........................................................................................................................................................40 7.1 REFERENCE..........................................................................................................................................................40 7.2 EQUIPMENTS LIST & CALIBRATION INFO.............................................................................................................41 7.3 IEEE SCC-34/SC-2 P1528 RECOMMENDED TISSUE DIELECTRIC PARAMETERS.................................................42 7.4 EQUIPMENT CALIBRATION CERTIFICATE.............................................................................................................42 8 - SAR SETUP PHOTOGRAPHS ...............................................................................................…

Text truncated - open the document above for the full version.

Note: This test report is specially limited to the above client company and the product model only. It may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. SAR EVALUATION REPORT For VTech Telecommunications Ltd. 23/F Tai Ping Industrial Center Block 1 57 Ting Kok Road, Tai Po NT, Hong Kong Model: VT 5831 April 1, 2002 This Report Concerns: Original Report Equipment Type: Cordless Phone Test Engineer: Jeff Lee Report No.: R0203182 Test Date: March 31, 2002 Certified By: John Y. Chan - Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732-9162 Fax: (408) 732 9164 VTech Telecommunications Ltd. Model: VT 5831 Report #R0203182.doc SAR Evaluation Report Page 2 of 50 CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Applicant: VTech Telecommunications Ltd. 23/F Tai Ping Industrial Center Block 1 57 Ting Kok Road, Tai Po NT, Hong Kong Trade Name: N/A Model: 2.4GHz Cordless Phone Handset Serial Number: N/A FCC ID: EW780-5198-01 Dates of Tests: March 31, 2002 Report No: R0203182 Tx Frequency: 2400.97 ~ 2482.67 MHz Max. RF Output Power: 22.2dBm (0.166Watt) RF Exposure environment: General Population/Uncontrolled Application Type: Certification FCC Rule Part(s): FCC 15.247 This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. John Chan Engineering Manager VTech Telecommunications Ltd. Model: VT 5831 Report #R0203182.doc SAR Evaluation Report Page 3 of 50 TABLE OF CONTENTS CERTIFICATE OF COMPLIANCE (SAR EVALUATION)............................................................................................2 1 - EUT DESCRIPTION................................................................................................................................................................4 2 - REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC....................................................5 3 - DOSIMETRIC ASSESSMENT SETUP..............................................................................................................................6 3.1 MEASUREMENT SYSTEM DIAGRAM......................................................................................................................................7 3.2. SYSTEM COMPONENTS...........................................................................................................................................................8 3.3. EUT ARRANGEMENT...........................................................................................................................................................12 3.4 MEASUREMENT UNCERTAINTY...........................................................................................................................................17 4 - EUT TUNE-UP PROCEDURE...........................................................................................................................................18 5 - EVALUATION PROCEDURE...........................................................................................................................................19 5.1 SIMULATED TISSUE LIQUID PARAMETER CONFIRMATION..............................................................................................19 5.2 SYSTEM ACCURACY VERIFICATION....................................................................................................................................19 5.3 SAR EVALUATION PROCEDURE..........................................................................................................................................21 5.4 EXPOSURE LIMITS..................................................................................................................................................................22 6 - TEST RESULTS......................................................................................................................................................................23 6.1 LEFT HEAD CONFIGURATION...............................................................................................................................................23 6.2 RIGHT HEAD CONFIGURATION............................................................................................................................................23 6.3 BODY WORN CONFIGURATION............................................................................................................................................23 6.4 LIQUID MEASUREMENT RESULT..........................................................................................................................................23 7 - REFERENCE...........................................................................................................................................................................40 7.1 REFERENCE.............................................................................................................................................................................40 7.2 EQUIPMENTS LIST & CALIBRATION INFO..........................................................................................................................41 7.3 IEEE SCC-34/SC-2 P1528 RECOMMENDED TISSUE DIELECTRIC PARAMETERS...…

Text truncated - open the document above for the full version.

Test Report:2W04767 Applicant:VTECH ENGINEERING CANADA 200-7671 Alderbridge Way Richmond, BC V6X 1Z9 Equipment Under Test:VTECH 5831 (EUT)Cordless Telephone Set FCC ID: In Accordance With:FCC Part 15, Subpart C Frequency Hopping Spread Spectrum Transmitters 2400 - 2483.5 MHz & 5725 – 5850 MHz Tested By:Nemko Canada Inc. 3325 River Road, R.R. 5 Ottawa, Ontario K1V 1H2 Authorized By: J. Harrington, RF Group Manager Date:12 March 2002 Total Number of Pages:70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 2 of 70 Table of Contents Section 1. Summary of Test Results......................................................................................3 Section 2. General Equipment Specification........................................................................5 Section 3. Powerline Conducted Emissions..........................................................................8 Section 4. Channel Separation............................................................................................12 Section 5. Pseudorandom Hopping Algorithm...................................................................15 Section 6. Time of Occupancy.............................................................................................30 Section 7. Occupied Bandwidth..........................................................................................35 Section 8. Peak Power Output.............................................................................................42 Section 9. Spurious Emissions.............................................................................................49 Section 10.Block Diagrams....................................................................................................69 Section 11.Test Equipment List............................................................................................70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 3 of 70 Section 1.Summary of Test Results General All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C, Paragraph 15.247 for Frequency Hopping Spread Spectrum devices. Radiated tests were conducted is accordance with ANSI C63.4-1992. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. TESTED BY: Glen Westwell, Wireless Technologist Date: Mar 12 2002 Nemko Canada Inc., a testing laboratory, is accredited by the Standards Council of Canada. The tests included in this report are within the scope of this accreditation. The results apply only to the samples tested. Nemko Canada Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 4 of 70 Summary Of Test Data Name Of TestPara. No.Result Powerline Conducted Emissions15.207(a)Complies Channel Separation15.247(a)(1)Complies Pseudorandom Hopping Algorithm15.247(a)(1)Complies Time of Occupancy15.247(a)(1)(ii)Complies 20 dB Occupied Bandwidth15.247(a)(1)Complies Peak Power Output15.247(b)Complies Spurious Emissions (Radiated)15.247(c)Complies Footnotes: Test Conditions: IndoorTemperature:22°C Humidity:36% OutdoorTemperature:-5°C Humidity:42% Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 5 of 70 Section 2.General Equipment Specification Manufacturer: Vtech Engineering Canada Model No.: Vtech 5831 Serial No.: Base: BS01 Portable: HS01 Date Received In Laboratory: 2 Feb. 2002 Nemko Identification No.: #1&2 Frequency Range:Base:5744.736 – 5825.952 MHz Portable:2401.056 – 2482.272 MHz Number of Channels:75 Channel Spacing:864KHz (typical) Rated Output Power (into antenna):Base:28.5dBm (typical) Portable:23dBm (typical) Antenna Gain:2dBi Emission Designator:700KF1D Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 6 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 7 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 8 of 70 Section 3.Powerline Conducted Emissions Para. No.: 15.207 (a) Test Performed By: Glen WestwellDate of Test: 26 Feb. 2002 Test Results:Complies. Measurement Data:See attached graph(s). Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 9 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 10 of 70 Front View Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 11 of 70 Side View Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 12 of 70…

Text truncated - open the document above for the full version.

Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 36 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 37 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 38 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 39 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 40 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 41 of 70 Nemko Canada Inc.FCC PART 15, SUBPART C FREQUENCY HOPPING TRANSMITTERS PROJECT NO: 2W04767 EQUIPMENT: VTECH 5831 Cordless Telephone Page 42 of 70 Section 8.Peak Power Output Para. No.: 15.247 (b) Test Performed By: Glen WestwellDate of Test: 26 Feb 2002 Test Results:Complies. The maximum peak power output of the transmitter is: Base = 0.918 watts / 29.6dBm (E.I.R.P.) Portable = 0.164 watts / 22.2dBm (E.R.I.P.) Measurement Data:Detachable antenna? Yes No Directional Gain …

Text truncated - open the document above for the full version.