EW780-5348-00VTech 5825 & 5850

Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. To reduce the risk of electric shock, do not disassemble this product. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect eassembling can cause electric shock when the appliance is subsequently used. 11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and contact VTECH under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. 13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 14. Do not use this or any cordless telephone to report a gas leak in the vicinity of the leak. VTECH COMMUNICATIONS INC . CUSTOMER SERVICE : 1-800-595-9511. In Canada, call VTech Electronics Ltd. At 1-800-267-7377. BEFORE USING YOUR ip 5825 SYSTEM, CAREFULLY PEEL OFF THE PROTECTIVE FILM, COVERING THE DISPLAYS. SAVE THESE INSTRUCTIONS 1 Introduction The ip 5825 is an advanced cordless telephone that operates in the 5.8GHz frequency range. Your ip 5825 is capable of supporting up to a maximum of 2 Handsets. This manual is designed to familiarize you with the ip 5825 cordless telephone. We strongly recommend you read the manual before using your phone. STOP!! If you have questions about this product, or if you’re having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at 1-800-595-9511 In Canada, call 1-800-267- 7377 2 Parts Check List 1. Base Unit 6. Belt Clip 2. Handset 7. Base Wall Mounting Bracket 3. Handset Charger 8. Charger Wall Mounting Bracket 4. Base AC Power Adapter 9. Owner’s Manual 5. Telephone Line Cord 10. Battery Cells To purchase replacement battery cells, call VTech Communications Inc. at 1-800-595-9511. In Canada, call VTech Electronics Ltd. at 1-800-267-7377. Placing the parts here which including in GB 3 The Handset Layout Place the HS here with relative call-outs 1. Antenna 2. Volume Control 3. Soft Keys 4. CID 5. Select (Menu) 6. On (Flash) 7. Dialing Keys (0-9, *, #) 8. Redial (Pause) 9. Mute (Delete) 10. Speakerphone 11. LCD Display 12. Headset jack (2.5mm) 13. Phonebook 14. Off (Clear) 15. Intercom 4 The Base Unit Layout Place the Base here with relative call-outs 1. In Use LED 2. Charging LED 3. Message Waiting LED 4. Page key 5 Setup Connecting power to Base Unit/Handset Charger 1. Plug the AC power adapter into an electrical outlet, and the DC connector into the bottom of the Base Unit. Place Base illustration here 2. Choose the location for your Handset Charger, and plug its power supply into an electrical outlet. Place charger illustration here Installation of Battery Cells in Handset Place the illustration showing the step of installation of battery cells Follow the steps below: 1. Remove the battery cover by pressing on the indent and sliding downward. 2. Place the new battery cells in the Handset with the positive and negative poles aligned in the battery compartment. 3. Replace the battery cover by sliding it upwards. 4. If the new battery cells are not already charged, place the Handset in its Charger, and allow it to charge for 12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient. 6 Charging of the Handset Battery Cells The Handset of your ip 5825 cordless telephone is powered by a rechargeable battery cells. It charges automatically whenever the Handset is in its charger. You should charge the battery pack for 12 hours when you first receive your phone. You’ll know the battery pack needs charging when: • The low battery message is displayed : • The Handset seems completely dead, the LCD is completely clear and does not a…

Text truncated - open the document above for the full version.

IMPORTANT SAFETY INSTRUCTIONS...............................................................................................3 INTRODUCTION........................................................................................................................................4 PARTS CHECK LIST.....................................................................................................................................5 THE HANDSET LAYOUT...............................................................................................................................6 THE BASE UNIT LAYOUT............................................................................................................................7 GETTING STARTED..................................................................................................................................8 SETUP..........................................................................................................................................................8 Connecting power to Base Unit/Handset Charger.................................................................................8 Installation of Battery Cells in Handset.................................................................................................8 Charging of the Handset Battery Cells...................................................................................................9 Connecting to phone line........................................................................................................................9 Checking for dial tone............................................................................................................................9 WALL MOUNTING.....................................................................................................................................10 BASIC OPERATION.................................................................................................................................11 HANDSET AND BASE INDICATORS.............................................................................................................11 Handset Icons.......................................................................................................................................11 Handset LEDs.......................................................................................................................................11 Base Unit Icons.....................................................................................................................................11 Base LEDs............................................................................................................................................11 PHONE BOOK OPERATION.........................................................................................................................12 Storing a new entry...............................................................................................................................12 Dialing from the phone book................................................................................................................14 Editing a phone book entry...................................................................................................................14 Delete a phone book entry....................................................................................................................15 CALLS LOG (CALLER ID)..........................................................................................................................16 QUICK DIALING.........................................................................................................................................18 Entering a Quick Dial number.............................................................................................................18 Reviewing quick dial numbers..............................................................................................................19 Dialing a Quick Dial number...............................................................................................................20 HANDSET SETTING....................................................................................................................................20 Ring Volume.........................................................................................................................................21 Ring tone...............................................................................................................................................21 Key Click..............................................................................................................................................22 Handset Name......................................................................................................................................23 Language..............................................................................................................................................24 Clear Message waiting.........................................................................................................................24 Dial Method..........................................................................................................................................25 HANDSET OPERATION...............................................................................................................................26 Making Calls........................................................................................................................................26 Answering Calls....................................................................................................................................26 Intercom Call........................................................................................................................…

Text truncated - open the document above for the full version.

1 When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). 5. Do not place this product on an unstable cart, stand, or table. The prod- uct may fall, causing serious damage to the product. 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used. 11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and contact VTECH under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. 13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Important Safety Instructions 2 Important Safety Instructions If you have questions about this product, or if you're having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at 1-800-595-9511 In Canada, call 1-800-267-7377 STOP!! 14. Do not use this or any cordless telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS 3 Introduction This is an advanced cordless telephone, capable of supporting 2 Handsets. This manual is designed to familiarize you with this cordless telephone. We strongly recommend you read the manual before using your phone. 4 Parts Check List To purchase replacement battery cells, call VTech Communications, Inc. at 1-800- 595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267- 7377. Note : Use only VTech batteries P/N 80-5380-00-00 or equivalent AAA NiMH rechargeable batteries. 6. Belt Clip 7. Base Wall Mounting Bracket 8. Charger Wall Mounting Bracket 9. Owner’s Manual 10. Battery Cells 1. Base Unit 2. Handsets 3. Handset Charger 4. Base AC Power Adapter 5. Telephone Line Cord 5 1. Antenna 2. Earpiece 3. Volume Control 4. CID (Scroll Up) 5. On (Flash) 6. Dialing Keys (0-9, *, #) 7. Redial (Pause) The Handset Layout 8. Speakerphone 9. LCD Display 10. Select (Menu) 11. Phonebook(Scroll Down) 12. Headset jack (2.5mm) 13. Off (Clear) 14. Intercom 15. Mute (Delete) 6 1. In Use LED 2. Charging LED 3. Message Waiting LED 4. Page key 5. DC Connector 6. Telephone Jack The Base Unit Layout
     
      
 !!"#$%&%''%'$$ (((") * 

   7 Connecting power to Base Unit/Handset Charger 1. Plug the AC power adapter into an electrical outlet, and the DC connector into the bottom of the Base Unit. Setup 2. Choose the location for your Handset Charger, and plug its power supply into an electrical outlet. Getting Started
     
      
 !!"#$%&%''%'$$ (((") * 

   8 Installation of Battery Cells in Handset Setup Follow the steps below: 1. Place the new battery cells in the andset with the positive and negative poles aligned in the battery compart- ment. 2. Place the battery cover by sliding it upwards 3. If the new battery cells are not already charged, place the Handset in its Charger, and allow it to charge for 12 hours. After initial charge, a mainte- nance charge of 8 hours should be sufficient. Getting Started Charging of the Handset Battery Cells The Handset of your cordless telephone is powered by rechargeable battery cells. It charges automatically whenever the Handset is in its charger. You should charge the battery pack for 12 hours when you first receive your phone. You’ll know the battery pack needs charg- ing when: • The low battery message is displayed : • The Handset seems completely dead, the LCD is completely clear and does not activate when you pres…

Text truncated - open the document above for the full version.

1 When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). 4. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used. 11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and contact VTECH under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. Important Safety Instructions 2 13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 14. Do not use this or any cordless telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS Important Safety Instructions If you have questions about this product, or if you're having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at 1-800-595-9511 In Canada, call 1-800-267-7377 STOP!! 3 This is an advanced cordless telephone, capable of supporting 2 Handsets. This manual is designed to familiarize you with this cordless telephone. We strongly recommend you read the manual before using your phone. STOP!! If you have questions about this product, or if you’re having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at 1-800-595-9511 In Canada, call 1-800-267-7377 Introduction 4 1. Base Unit 2. Handset 3. Handset Charger 4. Base AC Power Adapter 5. Telephone Line Cord Parts Check List 6. Belt Clip 7. Base Wall Mounting Bracket 8. Charger Wall Mounting Bracket 9. Owner’s Manual 10. 6 AAA Cells To purchase replacement battery cells, call VTech Communications, Inc. at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267-7377. Note: Use only VTech batteries P/N 80-5380-00-00 or equivalent AAA NiMH rechargeable batteries. 5 1. Antenna 2. Earpiece 3. Volume Control 4. CID 5. On (Flash) 6. Dialing Keys (0-9, *, #) 7. Redial (Pause) 8. Speakerphone The Handset Layout 9. LCD Display 10. Select (Menu) 11. Phonebook 12. Headset jack (2.5mm) 13. Off (Clear) 14. Intercom 15. Mute (Delete) 6 1. 2. 3. 4. 5. 6. 7. 8. The Base Unit Layout 9. 10. 11. 12. 13. 14. 15. 7 Connecting power to Base Unit/Handset Charger 1. Plug the AC power adapter into an electrical outlet, and the DC connector into the bottom of the Base Unit. Setup 2. Choose the location for your Handset Charger, and plug its power supply into an electrical outlet. Getting Started 8 Installation of Battery Cells in Handset Setup Follow the steps below: 1. Remove the battery cover by pressing on the indent and sliding downward. 2. Place the new battery cells in the Handset with the positive and negative poles aligned in the battery compartment. 3. Replace the battery cover by sliding it upwards. 4. If the new battery cells are not already charged, place the Handset in its Charger, and allow it to charge for 12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient. Getting Started Charging of the Handset Battery Cells The Handset of your cordless telephone is powered by rechargeable battery cells. It charges automatically whenever the Hand- set is in its charger. You should charge the battery pack for 12 hours when you first receive your phone. You’ll know the battery pack needs charging when: • The low battery message is displayed : • The Handset seems completely dead, the LCD is completely clear and does not activate when you…

Text truncated - open the document above for the full version.

11 Handset and Base Indicators Basic Operation Handset LEDs LED Description . Base LEDs LED Description IN USE CHARGING PAGE MAILBOX 1,2,3 VOLUME^/v MENU CHANGE TIME/SET REC/MEMO DELETE REPEAT/ SLOW SKIP/ QUICK • On when the phone is off hook. • Flashes when an extension phone or the TAD is off hook. • On when the handset is charging in the cradle. • Will perform a global page. • Flashes when new messages are in the appropriate mailbox. On when only old messages are in the appropriate mailbox. Off when no messages are in the appropriate mailbox. • Adjusts the ITAD speaker volume. There are 7 volume levels. • This key is used to scroll through the ITAD menu options • This key is used to select the various menu options. • When pressed in idle mode, the current time will be announced. When pressed in menu mode, the current setting will be confirmed or reviewed. • This key will put the ITAD into record mode to record the OGM or a memo. • This key will cause the ITAD to erase the ICM, OGM or memo. One or all messages can be erased. • This key is used to repeat a message or play a mes- sage slowly. If the key is pressed and released, the message will be repeated. If the key is held, the message will play back at half the normal speed. • This key is used to skip a message or play a mesage quickly. If the key is pressed and released, the message will be skipped. If the key is held, the message will play back at twice the normal speed. Base Unit Icons Icon Description • Speaker LED (Orange) • LED is on when in a handsfree mode. 12 Making Calls • Press ON (or, SPEAKERPHONE to use the Handset Speakerphone feature). Dial the phone number. -OR- • Dial the phone number first; then press ON (or SPEAKERPHONE). • Press OFF to end your call Handset Operation Answering Calls From the Handset • Press any key except OFF and the softkeys. • Press OFF to end your call. Intercom Call Pressing INT key when the handset is idle ini- tiates an intercom call. • Press INT The call is performed and when the other handset answers, the display will change to: If the other handset is out of range, turned off or on an external call, the display will show and a busy tone will be heard on the earpiece, or through the speaker if in handsfree mode. An intercom call is terminated by: • Pressing OFF or INT, • Placing the handset in the charger After terminating an INTERCOM CALL, the display on both handsets will show: On the handset that did not terminate the call, a busy tone will be heard, indicating the other handset has ended the call. After several seconds the display will return to idle and the busy tone will stop. Basic Operation 13 The handsets share a common phone book, which is stored in the base station. This means that entries inserted by one handset are available for both handsets, and if one deletes a phone book entry, it will disappear from both handsets. The phone book size will hold 50 entries, with names of a maximum length of 16 characters and a 32-digit maximum phone number. The phone book entries are sorted and presented to the user in alphabetical order. Names are entered using the numerical keys. Multiple key presses of the dialing digit keys is used to generate characters, see the table below. The cursor moves to the next position if another numerical key is pressed or by pressing the key. The last entered character is deleted by pressing DELETE or . The entire name is cleared by holding down DELETE. Key Characters by number of key presses Basic Operation 1 2 3 4 5 6 7 8 9 0 * # 1 space A D G J M P T W 0 * # 2 1 B E H K N Q U X ? ‘ 3 C F I L O R V Y ! , 4 2 3 4 5 6 S 8 Z / - 5 a d g j m 7 t 9 ( . 6 b e h k n p u w ) & 7 8 9 c f i l o q r s v x y z The phone book is entered via the menu, as described below or by pressing the /\ key in idle (quick access key) whereby the handset jumps directly to the phone book search menu. The phone book is accessed as follows: 1) Press SEL, to enter the menu. 2) SEL, to enter the Phone book sub-menu. Phone Book Operation 14 Storing a new entry 1) Press the key in idle, or scroll through the sub-menu with the and keys and press SEL with “STORE” in the first line. 2) If the phone book is full the screen will show, 3) If the phone book is not full, the user will be prompted to enter the phone number to be stored as shown below: 4) Enter the number, up to 32 digits. Press DELETE to backspace. In cases the number exceeds 16 digits, the top line will be used to show the entire number. 5) Press SEL to confirm the number. If there is duplicate number in the phone book, the screen will show: and the Handset will return to the ‘STORE NUMBER’ screen. If the number is unique, you will move to the name entry screen, 6) Enter the associated name. Use 1 to add a space and DELETE to backspace. 7) Press SEL to confirm the name. A name must be entered, or you cannot proceed to the next step. Unlike phone numbers, duplicate names are allowed. The new record will be stored in the phone book. Basic Operation Phone Book Operation 15 The user can press CLEAR to return to the phone book operation screen, which will show the last operation: Dialing from the phone book A number can be recalled and dialed from the phone book by: 1) Press the key in idle, or scroll through the menu with the & keys and press SEL with “REVIEW” in the first line. The first phone book entry will be shown. 2) Scroll through the phone book entries using and keys or enter first character of the name to be searched (using the dial digit keys) and continue navigating using the or as scroll keys, until you reach the entry to be dialed. 3) Press ON or SPK, to dial the number. Editing a phone book entry 1) Press the key in idle, or scroll through the menu with the & keys and press SEL with “REVIEW” in the first line. 2) Scroll through the phone book entries using and keys or enter first character of the name to be searched (using the dialing keys) and continue navigating using the or as scroll keys, until you reach the entry t…

Text truncated - open the document above for the full version.