EW780-5587-01Vtech 5829 & 5851 Handset

1 Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool). 5. Do not place this product on an unstable surface, such as a table, shelf, or stand. The product may fall, causing serious damage. 6. Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it. 9. Never push objects of any kind into this product through slots in the base or handset as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: 2 Important Safety Instructions A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled onto the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation. E. If the product has been dropped and the base and/or handset has been damaged. F. If the product exhibits a distinct change in performance. 13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning. 14. Do not use the telephone to report a gas leak in the vicinity of the leak. 15. Only put the handset of your telephone next to your ear when it is in normal talk mode. 3 Enhanced 5.8GHz Technology - Dual band transmission combines the best of 5.8GHz and 900MHz technologies, providing enhanced performance over standard cordless telephones. Before You Begin 5. Battery 6. Belt Clip 7. User’s Manual Parts Check List 1. Base Unit 2. Handset 3. Base AC Power Adaptor 4. Telephone Line Cord Battery Belt Clip Telephone Line Cord User’s Manual (English and Spanish) Handset Base Unit Base AC Power Adaptor To purchase replacement batteries, call VTech Communications, Inc. at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267-7377. 4 The Handset Layout 1.Antenna 2.Earpiece 3.LCD 4.Left and Right Arrow Keys 5.Phone/Flash Key 6.Dialing Keys (0-9,*,#) 7.Chan/Delete Key 8.Microphone 9.Headset Jack 10. Select Key 11. Off Key 12. Hold Key 13. Redial/Pause Key 14. Prog Key
      





 5 The Base Unit Layout
    4. Telephone Line Jack 5. DC Connector Jack 1. Message Light 2. Page Key 3. Charging/In use Light 6 Getting Started Setup Installation and Charge of Battery 1.Install the battery. Use only VTech batteries. a) Remove battery compartment cover by pressing on the indentation and sliding downward. b) Align the two holes in the plug with the socket pins, then snap the plug into place. c ) Place the battery in the compartment with the wires in the lower right corner. d) Replace the battery compartment cover. e) If the battery is not already charged, place the handset in its base and allow to charge for 10 - 12 hours (or over- night). After that, be sure to place the handset in its base when not in use to ensure maximum daily performance. Connecting Power to Base Unit 2. Plug the DC connector to the base. Plug the AC adaptor into an electri- cal outlet.
   
     1. Choose a location for the base near an electrical outlet and a tele phone jack. This phone requires a modular telephone jack and a stan-dard electrical outlet (110V AC) not controlled by a wall switch. 7 Getting Started Setup
  
    2. If the phone will not be used for long periods of time, remove the battery to prevent possible leakage. NOTE: Install the base unit away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. Connecting to Phone Line Before connecting to the phone, make sure to properly charge the battery for at least 10 - 12 hours. Plug one end of the telephone line cord into the jack on the bottom of the base unit. Plug the other end of this cord into the wall jack. Battery Care and Maintenance •The maximum standby time on a fully charged battery is six days. Average talk time on a fully charged battery is five hours. •The …

Text truncated - open the document above for the full version.

1 Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool). 5. Do not place this product on an unstable surface, such as a table, shelf or stand. The product may fall, causing serious damage. 6. Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it. 9. Never push objects of any kind into this product through slots in the base or handset as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled onto the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation. 2 Important Safety Instructions E. If the product has been dropped and the base and/or handset has been damaged. F. If the product exhibits a distinct change in performance. 13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning. 14. Do not use the telephone to report a gas leak in the vicinity of the leak. 15. Only put the handset of your telephone next to your ear when it is in normal talk 3 1.Handset 2.Base Unit 3.Battery 4.Belt Clip 5.Wall Mount Bracket 6.Telephone Line Cord 7.Base AC Power Adaptor 8.User’s Manual To purchase replacement battery, call VTech Communications, Inc. at 1-800- 595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800- 267-7377. Parts Check List: Before You Begin Enhanced 5.8GHz Technology - Dual band transmission combines the best of 5.8GHz and 900MHz technologies, providing enhanced performance over stan- dard cordless telephones. Handset Base Unit BatteryBelt Clip Telephone Line CordBase AC Power AdaptorUser’s Manual Wall Mount Bracket 4 The Handset Layout 1.Antenna 2.Earpiece 3.LCD 4.Left and Right Arrow Keys 5.Phone/Flash Key 6.Dialing Keys (0-9,*,#) 7.Chan/Delete Key 8.Microphone 9.Headset Jack 10. Select Key 11. Off Key 12. Hold Key 13. Redial/Pause Key 14. Prog Key
      





 5 1.Antenna 2.Vol -/+ Keys 3.Time/Set Key 4.In Use/Charging Light 5.Repeat/Slow Key 6.Select Key 7.Menu Key 8.Rec/Memo Key 9.Answer On/Off Key 10.Answer On/Off Light 11.Play/Stop (Mailbox) Keys 12.Skip/Quick Key 13.Delete Key 14.Page Key 15.DC Connector Jack 16.Telephone Line Jack The Base Unit Layout


      





6 Getting Started
    Connecting Power to Base Unit Plug the DC connector to the base.PLug the AC adaptor into electrical outlet. Setup Installation and Charge of Battery in Handset 1. Choose a location for the base near an electrical outlet and a telephone jack. This phone requires a modular telephone jack and a standard electri- cal outlet (110v AC) not controlled by a wall switch. 2. Install the Handset battery. Use only VTech batteries. a) Remove battery compartment cover by pressing on the indentation and sliding downwards. b) Align the two holes in the plug with the socket pins, then snap the plug into place. c) Place the battery in the compartment with the wires in the lower right corner. Angle the top of the battery under the top claws first, then snap the bottom of the pack in. Place the wires under the guide, located below the battery. d) Replace battery compartment cover. e) If the battery is not already charged, place the handset in its base and allow to charge for 10 - 12 hours (or overnight). After that, be sure to place the handset in its base when not in use to ensure maximum daily performance. 7 Getting Started Setup 3. Place the handset in the base. Charge the battery for 10-12 hours. 4. If the phone will not be used for long periods of time, remove the battery to prevent possible leakage. Connecting to Phone Line NOTE: Before connecting to the phone, make sure to properly charge the battery for at least 10 - 12 hours. Plug one end of the telephone line cord into the jack on the bottom of the Base unit. Plug the othe…

Text truncated - open the document above for the full version.

36 Additional Information FCC, ACTA and IC Regulations This equipment complies with Parts 15 of the Federal Communications Commission (FCC) rules for the United States. It also complies with regulations RSS210 and CS-03 of Industry and Science Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. A label is located on the underside of the Base Unit containing either the FCC registration number and Ringer Equivalence Number (REN) or the IC registration number and Load Number. You must, upon request, provide this information to your local telephone company. This equipment is compatible with inductively coupled hearing aids. Should you experience trouble with this telephone equipment, please contact: VTech Communications Inc. CUSTOMER SERVICE at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267-7377 for repair/warranty information. The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected. FCC Part 15 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. 37 Additional Information FCC, ACTA and IC Regulations FCC and ACTA Information If this equipment was approved for connection to the telephone network prior to July 23, 2001, it complies with Part 68 of the Federal Communications Commission (FCC) rules. If the equipment was approved after that date, it complies with the Part 68 rules and with Technical Requirements for Connection of Equipment to the Telephone Network adopted by the Administrative Council for Terminal Attachments (ACTA). We are required to provide you with the following information. 1. Product identifier and REN information The label on the back or bottom of this equipment contains, among other things, an identifier indicating product approval and the Ringer Equivalence Number (REN). This information must be provided to your local telephone company upon request. For equipment approved prior to July 23, 2001, the product identifier is preceded by the phrase “FCC Reg No.” and the REN is listed separately. For equipment approved after that date, the product identifier is preceded by “US” and a colon (:), and the REN is encoded in the product identifier without a decimal point as the sixth and seventh characters following the colon. For example, the product identifier US:AAAEQ03T123XYZ would indicate an REN of 0.3. The REN is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company. 2. Connection and use with the nationwide telephone network The plug and jack used to connect this equipment to the premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in this user’s manual. This equipment may not be used with Coin Telephone Lines or with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset has such a low power that it does not require testing. It may be safely held against the ear of the user. The base unit shall be installed & used such that parts of the user’s body other than the hands should be maintained at a comfortable distance of approxi- mately 20 cm or more. 38 Additional Information FCC, ACTA and IC Regulations of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. 3. Repair instructions If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty. 4. Rights of the telephone company If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone comp…

Text truncated - open the document above for the full version.

November 18, 2004 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Nemko Canada Inc, 203 River Road, Ottawa, Ontario, Canada K1V 1H2, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with VTech Engineering Canada, 200-7671 Alderbridge Way, Richmond B.C., Canada V6X 1Z9. Dated this 18th Day of November 20 04 Agency agreement expiration date: July 31, 2005 By: Joseph Poon Signature Printed Title: Regulatory Compliance Manager On behalf of : VTech Engineering Canada Ltd. Telephone: (604) 273-5131

November 18, 2004 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: EW780-5587-00 (Base) EW780-5587-01 (Handset) Product Name: Vtech 5829 & Vtech 5851 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents (list no# 1 to 5) be held confidential: (1) Theory of Operation (2) Wireless System Description (3) Schematics (4) Block Diagrams (5) Parts List We also request that the FCC mark the below documents (list no# 6 to 8) as "Temporary Confidential" as outlined in Public Notice DA 04-1705, dated June 15, 2004. This provision will give Vtech temporary confidentiality prior to product launch. (6) External Photos (7) Internal Photos (8) Users Manual These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 18th Day of November 2004 By: Joseph Poon Signature Printed Title: Regulatory Compliance Manager On behalf of : VTech Engineering Canada Ltd. Telephone: (604) 273-5131

Vtech 5829 Cosmetic

Vtech 5851 Cosmetic

CAUTION: Danger of explosion if battery is incorrectly replaced. USE ONLY VTECH BATTERY 89-1323-00-00 FCC ID: EW780-5587-01 IC: 1135A-80558700 LABEL HS IC: 1135A-80558700 MODEL: 5829 VTECH TELECOMMUNICATIONS LTD. MANUFACTURED IN CHINA COMPLIES WITH 47 CFR PART 68 REGISTRATION NO.: US: EW7W401B80-558700 RINGER EQUIVALENCE: 0.1B USOC JACK: RJ11C/RJ11W HAC THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. TEL LINE 9V DC VTECH TELECOMMUNICATIONS LTD.DC 9V 400mACLASS 2 POWER SOURCE ONLY VTech Customer Service 1-800-595-9511www.vtechphones.com CORDLESS TELEPHONE ia 5829 engraving BS

ia 5851 engraving BS IC LABEL SERIAL NO. LABEL VTECH TELECOMMUNICATIONS LTD. DC 9V 500mA CLASS 2 POWER SOURCE ONLY VTech Customer Service 1-800-595-9511 www.vtechphones.com CORDLESS TELEPHONE MODEL: 5851 VTECH TELECOMMUNICATIONS LTD. MANUFACTURED IN CHINA COMPLIES WITH 47 CFR PART 68 REGISTRATION NO.: US: EW7W401B80-558700 RINGER EQUIVALENCE: 0.1B USOC JACK: RJ11C/RJ11W THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. FCC ID: EW780-5587-00 HAC IC: 1135A-80558700 TEL LINE 9V DC HS CAUTION: Danger of explosion if battery is incorrectly replaced. USE ONLY VTECH BATTERY 89-1323-00-00 FCC ID: EW780-5587-01 IC: 1135A-80558700 LABEL

Vtech 5829/5851/5839/5859 Handset PCB Vtech 5829/5851/5839/5859 Handset PCB Vtech 5829/5851/5839/5859 Handset PCB

Master: PT15-SubC-15249 Date: October 17, 2001 Test Report: 4W33046 Issue 2 Applicant: VTech Engineering Canada Ltd. Suite 200 – 7671 Alderbridge Way Richmond, B.C., Canada V6X 1Z9 Equipment Under Test: VTech 5829,5851 Handset (EUT) FCC ID: EW780-5587-01 In Accordance With: FCC Part 15, Subpart C, 15.249 Tested By: Nemko Canada Inc. 303 River Road, R.R. 5 Ottawa, Ontario K1V 1H2 Authorized By: Glen Westwell, Wireless Specialist Date: 9 December 2004 Total Number of Pages: 15 Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 2 of 15 Table Of Contents Section 1. Summary Of Test Results ...................................................................................3 Section 2. General Equipment Specification ......................................................................5 Section 3. Radiated Emissions .............................................................................................7 Section 4. Occupied Bandwidth .........................................................................................10 Section 5. Block Diagrams..................................................................................................14 Section 6. Test Equipment List ..........................................................................................15 Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 3 of 15 Section 1. Summary Of Test Results General All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC Part 15.249. All tests were conducted using measurement procedure ANSI C63.4-2001. Radiated Emissions were made on an open area test site. A description of the test facility is on file with the FCC. THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. TESTED BY: ______________________________ DATE: 9 December 2004 Chris Maidens, EMC Specialist Nemko Canada Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 4 of 15 Summary Of Test Data Name Of Test Para. No. Result Conducted Emissions 15.207 N/A (1) Radiated Emissions 15.249 Complied Justification for N/A: The EUT is battery powered. Test Conditions: Indoor Temperature: 22°C Humidity: 30% Outdoor Temperature: 10°C Humidity: 30% Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 5 of 15 Section 2. General Equipment Specification Manufacturer: VTech (Dongguan) Electronics and Communications Ltd. Xia Ling Bei Management Zone, Liaobu, Dongguan, guangdong, China 523411 Model No.: 5829, 5851 Serial No.: None. Date Received In Laboratory: November 8, 2004 Nemko Identification No.: See Nemko Receiving Report EUT Description: ¾ The 5829 is a cordless phone system consisting of a CID handset unit that transmits in the 5863.8 to 5872.5MHz range, and a base unit that transmits in the 912.75 to 917.1MHz range. ¾ The 5851 system uses the same frequencies, but has a digital answering machine built in to the base. Tx Frequency Range: 5863.8-5872.5MHz Number of Channels: 30 Emission Designator: 633KF3E & 100KF1D Modulation: Voice: FM Data: FSK Rated Power: Transmit power is fixed at an output power which produces less than 94 dBuV at 3m Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 6 of 15 EUT Configuration Equipment Configuration List Item Description Identification: (M/N #, S/N #, P/N #, Rev.) A Handset None. B Headset with mini-din cable integral None. C Base Unit M/N: ia5829, ia5839, ia5851, or ia5859 D -48V DC feed None. E Component telephone power supply Class 2 M/N; UO93040D (with the ia5829 or ia5839) M/N: UO90050D (with the ia5851 or the ia5859) EUT Ports Item Description Indoor/Outdoor Type (See Legend) Qty i AC Mains Input Outdoor 1 1 ii PSTN Outdoor 3 1 iii Headset Indoor 4 1 Inter-Connection Cables Item Description Shielded Ferrite Length (m) 1 RJ11 to RJ11 Standards telephone cable No No 1.5 Legend: 1 = AC Power Input/Output, 2 = DC Power Input/Output, 3 = Telecom, 4 = Non-telecom I/O, 5 = Maintenance, 6 = Fiber Optic Notes None Configuration of the Equipment Under Test (EUT) Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 7 of 15 Section 3. Radiated Emissions Para. No.: 15.249 Test Performed By: Chris Maidens Date of Test: Nov 9 & 10, 2004 Minimum Standard: Fundamental (MHz) Field Strength (mV/m) Field Strength (dBμV) Harmonic (mV/m) Harmonic (dBμV) 902-928 50 94 0.5 54 Test Results: Complied Measurement Data: See attached tabulated data. Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 8 of 15 Radiated Emissions: Tested as per: Hand-Held Mains Input: 120VAC, 60Hz Test Distance (meters): 3 Dome: 1 Channel 14 (middle channel) Freq. (MHz) Ant. Pol. V/H RCVD Signal (dBμV) Ant. Factor (dB) Amp. Gain (dB) Cable Loss (dB) Field Strength (dBμV/m) Limit (dBμV/m) Margin (dB) Detector Amp. 5868.0000 Horn1 H 41.5 34.7 0 10.3 86.5 94.0 7.5 Peak N/A 5868.0000 Horn1 V 36.7 34.8 0 10.3 81.8 94.0 12.2 Peak N/A 11736.0000 Horn1 H 45.2 39…

Text truncated - open the document above for the full version.

Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 9 of 15 EUT Setup Photo:

Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.: 4W33046 Issue 2 EQUIPMENT: Vtech 5829,5851 Handset Page 9 of 15 EUT Setup Photo: