EW780-5735-02Cordless Telephone Base Transceiver

www.vtechphones.com 38 ADDITIONAL INFO FCC, ACTA and IC Regulation FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The base unit shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied VTech belt clip. FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request. The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company. This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty. If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone company is required to notify you if such changes are planned. If this product is equipped with a corded or cordless handset, it is hearing aid compatible. If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please: www.vtechphones.com 39 Additional Information ADDITIONAL INFO FCC, ACTA and IC Regulations * Remain on the line and briefly explain the reason for the call before hanging up. * Perform such activities in off-peak hours, such as early morning or late evening. Industry Canada This equipment complies with regulations RSS210 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met. The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The RBRC ® Seal The RBRC ® Seal on the nicke…

Text truncated - open the document above for the full version.

www.vtechphones.comTABLE OF CONTENTS 1 Tabel of Contents Before You Begin . . . . . . . . . . . . . . . . . . . . 4 Parts Check List: . . . . . . . . . . . . . . . . . . . 4 Getting Started . . . . . . . . . . . . . . . . . . . . . 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . 5 Choose Location . . . . . . . . . . . . . . . . . . . 5 Install Handset Battery . . . . . . . . . . . . . . . . 5 Connect Power and Telephone Line Cords. . . . . . 6 Wall Mounting. . . . . . . . . . . . . . . . . . . . . 7 Charge the Handset Battery . . . . . . . . . . . . . 8 Set Language Mode . . . . . . . . . . . . . . . . . 8 Check for Dial Tone. . . . . . . . . . . . . . . . . . 8 Set the Dial Mode. . . . . . . . . . . . . . . . . . . 8 Set Handset Date and Time. . . . . . . . . . . . . . 9 Handset Ringer Style/Battery Save. . . . . . . . . . 9 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation. . . . . . . . . . . . . . . . . . . . . . 10 Attach belt clip (optional). . . . . . . . . . . . . . . 10 Basic Operation. . . . . . . . . . . . . . . . . . . . 11 Telephone Operation. . . . . . . . . . . . . . . . . . 11 Handset Operation . . . . . . . . . . . . . . . . . 11 Base Operation . . . . . . . . . . . . . . . . . . . 12 Temporary Tone Dialing . . . . . . . . . . . . . . 13 Headset Jack . . . . . . . . . . . . . . . . . . . . 13 Operating Range . . . . . . . . . . . . . . . . . . 14 Message Waiting . . . . . . . . . . . . . . . . . . 15 Clear Message Waiting Alert . . . . . . . . . . . . 15 Display Screen Messages . . . . . . . . . . . . . 16 Speed Dial . . . . . . . . . . . . . . . . . . . . . . . 17 Store a Number/Name in Speed Dial . . . . . . . . 17 Edit a Speed Dial Number/Name . . . . . . . . . . 18 Delete a Speed Dial Number/Name. . . . . . . . . 19 Dial a Speed Dial Number . . . . . . . . . . . . . 19 Reassign Locations in Speed Dial . . . . . . . . . 19 Telephone Directory . . . . . . . . . . . . . . . . . . 20 Store a Number/Name in the Directory . . . . . . . 20 Edit a Number/Name in the Directory. . . . . . . . 20 Delete a Number/Name in the Directory . . . . . . 21 Move a Number/Name to Speed Dial . . . . . . . 22 Dial a Number from the Directory. . . . . . . . . . 22 Caller ID Operation. . . . . . . . . . . . . . . . . . . 23 About Call History (Caller ID) . . . . . . . . . . . . 24 Review Call History . . . . . . . . . . . . . . . . . 24 Delete Records from Call History . . . . . . . . . . 25 Dial a Displayed Number . . . . . . . . . . . . . . 25 Store a Call History Record in the Directory . . . . 25 Display Screen Messages . . . . . . . . . . . . . 26 Batteries . . . . . . . . . . . . . . . . . . . . . . . . 27 Battery Care and Maintenance . . . . . . . . . . . 27 TABLE OF CONTENTSwww.vtechphones.com 2 Replacing the Handset Battery . . . . . . . . . . . 27 Additional Information . . . . . . . . . . . . . . . . 28 Troubleshooting . . . . . . . . . . . . . . . . . . . . 28 Maintenance . . . . . . . . . . . . . . . . . . . . . . 35 Warranty Statement . . . . . . . . . . . . . . . . . . 35 Important Safety Instructions. . . . . . . . . . . . . . 37 FCC, ACTA and IC Regulations . . . . . . . . . . . . 38 The RBRC ® Seal. . . . . . . . . . . . . . . . . . . . 39 Technical Specifications . . . . . . . . . . . . . . . . 40 NEED HELP? This book has all the feature operation and troubleshooting you need to install and operate your new VTech phone. Please take the time to review thoroughly to ensure proper installation and the benefit of this VTech innovative and feature rich product. You can also visit our website at www.vtechphones.com for support, shopping, and everything new at VTech. In Canada, please visit www.vtechcanada.com. VTech toll free 1-800-595-9511 In Canada dial 1-800-267-7377 www.vtechphones.com 4 Before You Begin GETTING STARTED Enhanced 5.8GHz technology - dual band transmission combines the best of 5.8GHz and 900MHz technologies, providing enhanced performance over standard cordless telephones. 1. Handset 2. Base Unit 3. Battery 4. Belt Clip 5. Telephone Line Cord 6. Base Power Adaptor 7. Desk/Wall Mount Bracket 8. User’s Manual To purchase replacement batteries, visit us on the web at www.vtechphones.com or call VTech Communications, Inc. at 1-800-595-9511. In Canada, contact VTech Telecommunications Canada Ltd. at www.vtechcanada.com or 1-800-267-7377. Parts Check List: Handset Base Unit Desk/Wall Mount Bracket Base Power Adaptor Battery Belt Clip Telephone Line Cord User’s Manual • Important! Before using this telephone, you must read important safety instructions on page 47 . www.vtechphones.com 5 Getting Started GETTING STARTED Installation Choose Location For maximum performance of your cordless telephone system: 1. Choose a central location for your Base Unit. 2. Install your Base Unit and Extension Handsets away from electronic equipment, such as personal computers, television sets and microwave ovens. 3. In locations where there are multiple cordless telephones, separate base units as much as possible. 4. Install your telephone equipment away from heat sources and sunlight. 5. Avoid excessive moisture, dust or extreme cold. a) Remove battery compartment cover by pressing on the indentation and sliding downwards. b) Align the two holes in the plug with the socket pins, then snap the plug into place. c) Place the battery in the compartment with the wires in the lower right corner. d) Replace cover by sliding it up into place. e) Place the handset in its base when not in use to ensure maximum daily performance. • Use only the provided VTech b a t t e r y , o r equivalent. Install Handset Battery 1 2 www.vtechphones.com 6 GETTING STARTED Connect Power and Telephone Line Cords Installation Standard electrical outlet Connect the power cord. After charging the battery for at least 18 hours as instructed on page 5, connect the telephone line cord. Modular telephone jack www.vtechphones.com 7 GETTING STARTED Getting Started Installation Wall Mo…

Text truncated - open the document above for the full version.

August 3, 2006 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Nemko Canada Inc, 203 River Road, Ottawa, Ontario, Canada K1V 1H2, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with VTech Telecommunications Canada Ltd., 200-7671 Alderbridge Way, Richmond B.C., Canada V6X 1Z9. Dated this 3rd Day of August 20 06 Agency agreement expiration date: August 30, 2006 By: Joseph Poon Signature Printed Title: Regulatory Compliance Manager On behalf of : VTech Telecommunications Canada Ltd. Telephone: (604) 273-5131

August 10, 2006 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: EW780-5735-02 (Base) Product Name: Vtech ia5823 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following document (list no# 1 to 3) be held confidential: (1) Schematics (2) Theory of Operation (3) Block Diagram These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 10th Day of August 2 0 06 By: Joseph Poon Signature Printed Title: Regulatory Compliance Manager On behalf of : VTech Telecommunications Canada Ltd. Telephone: (604) 273-5131

1 2

Vtech ia5823 Base PCB Vtech ia5823 Base PCB Vtech ia5823 Base PCB Vtech ia5823 Base RF PCB Vtech ia5823 Base RF PCB

FCC Part 15 Subpart C, 15.249 : August 2005 Test Report: 6W71020 Applicant: VTECH Engineering Canada 200-7671 Alderbridge Way Richmond, B.C. V6X 1Z9 Canada Apparatus: ia 5823 FCC ID: EW780-5735-02 In Accordance With: FCC Part 15 Subpart C, 15.249 Operation in the 902-928MHz, 2400 - 2483.5 MHz, 5725-5850 MHz and 24.0-24.25 GHz Tested By: Nemko Canada Inc. 303 River Road Ottawa, Ontario K1V 1H2 Authorized By: Jason Nixon, Telecom Specialist Date: August 16, 2006 Total Number of Pages: 27 Nemko Canada Inc. REPORT SUMMARY Report Number: 6W71020 FCC ID: EW780-5735-02 Specification: FCC Part 15 Subpart C, 15.249 Report Summary These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C. Radiated tests were conducted in accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: ia 5823 Specification: FCC Part 15 Subpart C, 15.249 Compliance Status: Complies Exclusions: None Non-compliances: None Report Release History: Original Release Author: Roman Kuleba, EMC/Wireless Specialist Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. Page 2 of 27 Nemko Canada Inc. REPORT SUMMARY Report Number: 6W71020 FCC ID: EW780-5735-02 Specification: FCC Part 15 Subpart C, 15.249 TABLE OF CONTENTS Report Summary.........................................................................................................................................2 Section 1 : Equipment Under Test.............................................................................................................4 1.1 Product Identification.................................................................................................................................4 1.2 Samples Submitted for Assessment............................................................................................................4 1.3 Theory of Operation...................................................................................................................................4 1.4 Technical Specifications of the EUT..........................................................................................................5 1.5 Block Diagram of the EUT.........................................................................................................................5 Section 2 : Test Conditions.........................................................................................................................6 2.1 Specifications.............................................................................................................................................6 2.2 Deviations From Laboratory Test Procedures ............................................................................................6 2.3 Test Environment.......................................................................................................................................6 2.4 Test Equipment...........................................................................................................................................6 Section 3 : Observations.............................................................................................................................7 3.1 Modifications Performed During Assessment ............................................................................................7 3.2 Record Of Technical Judgements...............................................................................................................7 3.3 EUT Parameters Affecting Compliance.....................................................................................................7 3.4 Test Deleted................................................................................................................................................7 3.5 Additional Observations.............................................................................................................................7 Section 4 : Results Summary.....................................................................................................................8 4.1 FCC Part 15 Subpart C : Test Results........................................................................................................9 Appendix A : Test Results........................................................................................................................10 Clause 15.207(a) Powerline Conducted Emissions.............................................................................................10 Clause 15.209(a) Radiated Emissions within Restricted Bands..........................................................................17 Clause 15.249(a) Radiated emissions not in Restricted Bands............................................................................18 Clause 15.249(d) Spurious emissions (except Harmonics)..................................................................................20 Appendix B : Setup Photographs............................................................................................................25 Appendix C : Block Diagram of Test Setups....…

Text truncated - open the document above for the full version.

1 2