EW780-5750-01Cordless Telephone Remote Transceiver

June 9, 2005 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Declaration on security code Dear Sir/Madam, FCC ID: EW780-5750-00 (Base) EW780-5750-01 (Handset) VTech T2326 and VTech T2340 cordless telephones use 20-bit of security code, randomly pre-fixed in the factory. Best Regards, Joseph Poon Regulatory Compliance Manager Vtech Engineering Canada Ltd.

27 FCC, ACTA and IC Regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These require - ments are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular in- stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The base unit shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopt - ed by the Administrative Council for Terminal Attachments (ACTA). The label on the back o r bottom of this equipment contains, among other things, a product identifier in the format US: AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon re - quest. The plug and jack used to connect this equipment to premises wiring and the telephone net - work must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company. This equipment may not be used with Party Lines. If you have specially wired alarm dialing equip - ment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty. If this equipment is causing harm to the telephone network, the telephone company may temporar - ily discontinue your telephone service. The telephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. 28 FCC, ACTA and IC Regulations You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper function - ing of this product. The telephone company is required to notify you if such changes are planned. If this product is equipped with a corded or cordless handset, it is hearing aid compatible. If this product has memory dialing locations, you may choose to store emergency telephone num - bers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please: • Remain on the line and briefly explain the reason for the call before hanging up. • Perform such activities in off-peak hours, such as early morning or late evening. Industry Canada This equipment complies with regulations RSS210 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met. The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indica - tion of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the require ment that the sum of the RENs of all the devices does not exceed five. The RBRC Seal The RBRC Seal on the nickel-cadmium battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of …

Text truncated - open the document above for the full version.

June 6, 2005 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Nemko Canada Inc, 203 River Road, Ottawa, Ontario, Canada K1V 1H2, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with VTech Engineering Canada, 200-7671 Alderbridge Way, Richmond B.C., Canada V6X 1Z9. Dated this 6th Day of June 20 05 Agency agreement expiration date: November 30, 2005 By: Joseph Poon Signature Printed Title: Regulatory Compliance Manager On behalf of : VTech Engineering Canada Ltd. Telephone: (604) 273-5131

June 6, 2005 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: EW780-5750-00 (Base) EW780-5750-01 (Handset) Product Name: Vtech T2326 & Vtech T2340 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents (list no# 1 to 4) be held confidential: (1) Theory of Operation (2) Wireless System Description (3) Schematics (4) Block Diagrams We also request that the FCC mark the below documents (list no# 5 to 7) as "Temporary Confidential" as outlined in Public Notice DA 04-1705, dated June 15, 2004. This provision will give Vtech temporary confidentiality prior to product launch. (5) External Photos (6) Internal Photos (7) Users Manual These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 6th Day of June 2 0 05 By: Joseph Poon Signature Printed Title: Regulatory Compliance Manager On behalf of : VTech Engineering Canada Ltd. Telephone: (604) 273-5131

June 6, 2005 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: EW780-5750-00 (Base) EW780-5750-01 (Handset) Product Name: Vtech T2326 and Vtech T2340 Dear Sir / Madam: Re: Application for an Original Certification The purpose of this document is to describe the differences between Vtech T2326 and Vtech T2340. They are all VTech designed new family models which are both 2.4GHz/900MHz analog cordless telephones with caller ID on handsets. Vtech T2326 : one handset & one base system Vtech T2340 : identical to Vtech T2326 plus one identical handset & standalone charger. The package configuration is 2 handsets, 1 base & 1 standalone charger Vtech T2326 and Vtech T2340 are with identical electronics on both handsets and bases. Sincerely, Joseph Poon Regulatory Compliance Manager VTech Engineering Canada Ltd.

Vtech T2326 Cosmetic Photo

Vtech T2340 Cosmetic Photo

T2340 HS/BS/CHARGER ENGRAVING FILE CHARGER BTM CORDLESS TELEPHONE VTECH TELECOMMUNICATIONS LTD. DC 6V 200mA CLASS 2 POWER SOURCE ONLY VTech Customer Service 1-800-595-9511 www.vtechphones.com CAUTION: Danger of explosion if battery is incorrectly replaced USE ONLY VTech BATTERY 80-5074-02-00 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTER- FERENCE; AND 2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE REC- EIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMM- UNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. CORDLESS TELEPHONE MANUFACTURED IN CHINA AC 9V 250mA CLASS 2 POWER SOURCE ONLY IC: 1135A-80575000 CAN IC label BS BTM HS RINGER EQUIVALENCE: 0.1B USOC JACK: RJ11C/RJ11W HAC FCC ID: EW780-5750-00 COMPLIES WITH 47 CFR PART 68 REGISTRATION NO.: US: EW7W401B80-575000 VTech Customer Service 1-800-595-9511 www.vtechphones. com IC: 1135A-80575000 EW780-5750-01 MODEL#: T2340 S/N:XXXXXXXXXX MODEL#: T2340 S/N:XXXXXXX

Vtech T2326/T2340 Base PCB Vtech T2326/T2340 Base PCB Vtech T2326/T2340 Base PCB

Vtech T2326/T2340 Handset PCB Vtech T2326/T2340 Handset PCB Vtech T2326/T2340 Handset PCB Vtech T2326/T2340 Handset PCB

Test Report: 5W45977, Issue 2 Applicant: VTECH Engineering Canada Ltd. Suite 200 – 7671 Alderbridge Way Richmond, B.C., Canada V6X 1Z9 Equipment Under Test: T2340 Analogue Cordless Phone T2326 Analogue Cordless Phone In Accordance With: FCC Part 15, Subpart C, 15.249 Tested By: Nemko Canada Inc. 303 River Road, R.R. 5 Ottawa, Ontario K1V 1H2 Authorized By: Sim Jagpal, General Manager Date: 10 June 2005 Total Number of Pages: 21 Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 2 of 21 Table Of Contents Section 1. Summary Of Test Results ...................................................................................3 Section 2. Summary Of Test Data .......................................................................................4 Section 3. General Equipment Specification ......................................................................5 Section 4. Powerline Conducted Emissions ........................................................................7 Section 5. Radiated Emissions ...........................................................................................11 Section 6. Block Diagrams..................................................................................................20 Section 7. Test Equipment List ..........................................................................................21 Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 3 of 21 Section 1. Summary Of Test Results General All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC Part 15.249. All tests were conducted using measurement procedure ANSI C63.4-2003. Radiated Emissions were made on an open area test site. A description of the test facility is on file with the FCC. THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. TESTED BY: ______________________________ DATE: 10 June 2005 Xu Jin, Wireless Specialist Nemko Canada Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 4 of 21 Section 2. Summary Of Test Data Summary Of Test Data Name Of Test Para. No. Result Power line Conducted Emissions 15.207(a) Complies Radiated Emissions 15.249 Complies Test Conditions: Indoor Temperature: 24°C Humidity: 50% Outdoor Temperature: 27°C Humidity: 60% Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 5 of 21 Section 3. General Equipment Specification Manufacturer: VTECH Engineering Model No.: T2340 Analogue Cordless Phone T2326 Analogue Cordless Phone Serial No.: Hand unit : PA 119(H) Base unit : PA 095(B) Date Received In Laboratory: May 30, 2005 Nemko Identification No.: T 2340 Hand Set PA119(H)___Item#1 T 2326 Base Set PA095(B)___Item#3 Frequency Range: Base: 2410.2-2418.9MHz Handset: 912.75-917.10MHz Number of Channels: 30 Modulation: FM Power Source: Base: 120VAC Handset : 3.6VDC Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 6 of 21 Theory of Operation T 2340 is a basic hybrid analogue cordless telephone. It consists of two mobile handsets and a fixed base unit. The base and Handset RF module are used as a RF combo to provide a full duplex wireless links between the handsets and base unit. This is accomplished by setting up two simultaneous communications links between the handset and base RF Modules. The RF receiver and transmitter circuitries essentially provide a link between the microphone and speaker in the handset to telephone line the base. The operation frequency from the handset to base is located from 912.75MHz to 917.10MHz. The operation frequency from the base to handset is located from 2410.2MHz to 2418.9MHz. T2326 is a basic hybrid analogue cordless telephone with a mobile unit and a fixed base unit. According to the manufacturer, same base and handset design are used in Model T2326 and T2340. There are two identical handset used in Model T2340 while only one handset is used in Model T2326. Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 7 of 21 Section 4. Powerline Conducted Emissions Para. No.: 15.207 (a) Test Performed By: Xu Jin Date of Test: May. 30, 2005 Test Results: Complies. Measurement Data: See attached graph(s). Limits For Conducted Disturbance At The Mains Ports Of Class B Limits dB(μV) Frequency Range MHz Quasi-Peak Average Result 0.15 to 0.50 66 to 56 56 to 46 0.5 to 5 56 46 5 to 30 60 50 Complies. Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 to 0.50MHz. 3. The test was performed using a peak detector. Note: Power line conducted emissions test was conducted for base unit with the handset on cradle. The handset was operated with fully charged battery. Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977, Issue 2 EQUIPMENT: VTECH T2340 & VTECH T2326…

Text truncated - open the document above for the full version.

Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 8 of 20 Conducted Disturbance at Mains Detailed Setup Photos

Nemko Canada Inc. FCC PART 15, SUBPART C, 15.249 PROJECT NO.:5W45977 EQUIPMENT: VTECH T2340 & VTECH T2326 Analogue Cordless Phone Page 17 of 20 Radiated Emissions Photos Hand Unit Base Unit