EW780-H0E4-06SIP Cordless Hotel Telephone

SIP Contemporary Series CTM-S2415 SIP Contemporary Cordless 1-line Hotel Phone CTM-S2415HC SIP Contemporary Cordless 1-line Accessory Handset and Charger Master User ‘s Guide EN - 2 1. This product should be installed by a qualified technician. 2. This product should only be connected to the host equipment and never directly to the network such as Public Switch Telephone Network (PSTN) or Plain Old Telephone Services (POTS). 3. Read and understand all instructions. 4. Follow all warnings and instructions marked on the product. 5. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 6. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 7. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 8. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided. 9. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply on the premises, consult your dealer or local power company. 10. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on. 11. Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 12. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 13. Do not overload wall outlets and extension cords. 14. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: • When the power supply cord or plug is damaged or frayed. • If liquid has been spilled onto the product. • If the product has been exposed to rain or water. • If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation. Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: EN - 3 English • If the product has been dropped and the telephone base and/or handset has been damaged. • If the product exhibits a distinct change in performance. 15. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning. 16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment containing concentrations of flammable or flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a fire or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc. 17. Only put the handset of your telephone next to your ear when it is in normal talk mode. 18. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 19. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. 20. In wall mounting position, make sure to mount the telephone base on the wall by aligning the eyelets with the mounting studs of the wall plate. Then slide the telephone base down on both mounting studs until it locks into place. Refer to the full instructions in Installation in the user’s manual. CAUTIONS • Keep small metallic objects such as pins and staples away from the handset receiver. • There may be a risk of explosion if a wrong type of handset battery is used (CTM-S2415, CTM-S2415HC). Use only the supplied rechargeable battery (BT164392/BT264392) or replacement battery (BT264392). Dispose of used batteries according to the information in The RBRC® seal in this user guide. SAVE THESE INSTRUCTIONS EN - 4 1. Ce produit doit être installé par un technicien qualifié. 2. Ce produit ne doit être connecté qu'à l'équipement hôte et jamais directement au réseau tel que le réseau téléphonique public commuté (RTPC) ou les services téléphoniques classiques (POTS). 3. Lire et comprendre toutes les instructions. 4. Respecter tous les avertissements et instructions figurant sur le produit. 5. Débranchez ce produit de la prise murale avant de le nettoyer. N'utilisez pas de nettoyants liquides ou en aérosol. Utilisez un chiffon humide pour le nettoyage. 6. N'utilisez pas ce produit près d…

Text truncated - open the document above for the full version.

VTech Telecommunications Ltd Oct. 12, 2020 To whom it may concern, Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows: Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout (Others, please specify) The only differences between these models are the follows for marketing purpose: Color Cosmetic details Trade name Model Number (Others, please specify) Suffix (“ ”) represents Color code Packing configuration (Others, please specify) Item No. New model Model Number Trade Name Remarks 1 YES CTM-S2125 vtech BS (VDP650)+ 2 line HS + Charger 2 YES CTM-S2115 vtech BS (VDP650)+ 1 line HS + Charger 3 YES CTM-S2415HC vtech 1 line HS + Charger 4 YES CTM-C4402 vtech 1 line HS 5 YES CTM-S2425HC vtech 2 line HS + Charger 6 YES CTM-C4502 vtech 2 line HS 7 YES CTM-S2415 vtech BS + 1 line HS + Charger 8 YES CTM-S2425 vtech BS + 2 line HS + Charger All above model's FCC ID is EW780-H0E4-06 for BS and HS, IC is 1135B-80H0E406 for BS and 1135B-80H0E407 for HS. The sample being submitted to Bay Area Compliance Labs Corp.(Shenzhen) for conformity assessment is CTM-S2415 and CTM-S2415HC (tested model) of the above list. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: [email protected] QA-FR-170-B FCC Authorization Date: 2020/09/17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, VTech Telecommunications Ltd, the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: [email protected] FCC Confidential Authorization Date: 2020/09/17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: EW780-H0E4-06 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, VTech Telecommunications Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 1 of 12 EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Base Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 2 of 12 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 3 of 12 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 4 of 12 Adapter Adapter Label Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 5 of 12 Handset Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 6 of 12 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 7 of 12 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 8 of 12 Charger Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 9 of 12 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 10 of 12 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 11 of 12 Adapter 1 (VT05UUS06040) Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 12 of 12 Adapter 2 (S003AKU0600040)

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF EXHIBIT A - FCC ID LABEL AND LOCATION For Base FCC ID Label Label 1 Label 2 FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Label 1 Label 2 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF For Handset FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 1 of 16 EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Base Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 2 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 3 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 4 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 5 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 6 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 7 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 8 of 16 5G Wi-Fi Antenna 2.4G Wi-Fi Antenna Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 9 of 16 DECT Antenna 0 DECT Antenna 1 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 10 of 16 Main Chip Handset Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 11 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 12 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 13 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 14 of 16 Antenna Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 15 of 16 Battery 1 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200811006-RF Page 16 of 16 Battery 2

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 13 of 150 FCC §15.247 (i) & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart 15.247 (i) and subpart 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (Minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Result Calculated Formulary: Predication of MPE limit at a given distance S = 2 4R PG  S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW). G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain. R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 14 of 150 Frequency (MHz) Antenna Gain Tune up conducted power Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric) (dBm) (mW) 2412-2462 1 1.26 19.0 79.43 20 0.02 1 5150-5250 2 1.58 13.0 19.95 20 0.006 1 5250-5350 2 1.58 13.0 19.95 20 0.006 1 5470-5725 2 1.58 13.0 19.95 20 0.006 1 5725-5850 2 1.58 15.0 31.62 20 0.010 1 1921.536 - 1928.448 0 1.0 20 100 20 0.02 1 Note: 1. The tune up conducted power was declared by the applicant 2. The 2.4G Wi-Fi can’t transmit at the same time with the 5G Wi-Fi. 3. The 2.4G Wi-Fi or 5G Wi-Fi can transmit with DECT function at the same time. Simultaneous transmitting consideration (worst case): The ratio=MPE 2.4G Wi-Fi /limit+MPE DECT /limit=0.02+0.02=0.04＜1.0, so simultaneous exposure is not required. To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm from nearby persons. Result: Pass

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. BACL is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15.407 RSS-GEN ISSUE 5, MARCH 2019 AMENDMENT 1 RSS-247, ISSUE 2, FEBRUARY 2017 TEST REPORT For FCC: VTech Telecommunications Ltd FCC: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong ISEDC: VTECH TELECOMMUNICATIONS LIMITED ISEDC: BL.1 23/F Tai Ping Industr Ctr. 57 Ting Kok Road Tai Po, NT Hongkong FCC ID: EW780-H0E4-06 IC: 1135B-80H0E406 Report Type: Original Report Product Type: SIP Cordless Hotel Telephone Re port Number: RSZ200811006B Re port Date: 2020-10-12 Reviewed B y: Jimmy Xiao RF En gineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone, Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 2 of 150 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 TEST METHODOLOGY .................................................................................................................................................. 5 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 DUTY CYCLE ................................................................................................................................................................ 9 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 9 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 9 EXTERNAL I/O CABLE .................................................................................................................................................. 9 BLOCK DIAGRAM OF TEST SETUP .............................................................................................................................. 10 SUMMARY OF TEST RESULTS ............................................................................................................................. 11 TEST EQUIPMENT LIST ......................................................................................................................................... 12 FCC §15.247 (i) & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................................ 13 APPLICABLE STANDARD ............................................................................................................................................ 13 RESULT ...................................................................................................................................................................... 13 RSS-102 § 4 –EXPOSURE LIMITS ........................................................................................................................... 15 APPLICABLE STANDARD ............................................................................................................................................ 15 FCC §15.203 & RSS-GEN §6.8– ANTENNA REQUIREMENT ............................................................................ 17 APPLICABLE STANDARD ............................................................................................................................................ 17 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 18 §15.407(b)(6)& §15.207(a) & RSS-Gen §8.8 CONDUCTED EMISSIONS ............................................................ 19 APPLICABLE STANDARD ............................................................................................................................................ 19 EUT SETUP ................................................................................................................................................................ 20 EMI TEST RECEIVER SETUP ............…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 96 of 150 Appendix A3: Min emission bandwidth Test Result TestMode Antenna Channel 6db EBW [MHz] Limit[MHz] Verdict 11A Ant1 574516.6400.5 PASS 578516.6400.5 PASS 582516.6400.5 PASS 11N20 Ant1 574517.7200.5 PASS 578517.7200.5 PASS 582517.7200.5 PASS 11N40 Ant1 575536.6400.5 PASS 579536.6400.5 PASS 11AC20 Ant1 574517.7200.5 PASS 578517.7200.5 PASS 582517.7200.5 PASS 11AC40 Ant1 575536.6400.5 PASS 579536.6400.5 PASS 11AC80 Ant1 577576.8000.5 PASS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 97 of 150 Test Graphs 11A_Ant1_5745 11A_Ant1_5785 11A_Ant1_5825 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 98 of 150 11N20_Ant1_5745 11N20_Ant1_5785 11N20_Ant1_5825 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 99 of 150 11N40_Ant1_5755 11N40_Ant1_5795 11AC20_Ant1_5745 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 100 of 150 11AC20_Ant1_5785 11AC20_Ant1_5825 11AC40_Ant1_5755 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 101 of 150 11AC40_Ant1_5795 11AC80_Ant1_5775 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 102 of 150 Appendix B-1 (FCC): Maximum conducted output power Test Result TestMode Antenna Channel Result[dBm] Limit[dBm] Verdict 11A Ant1 518012.19<=23.98 PASS 520012.23<=23.98 PASS 524012.77<=23.98 PASS 5260 12.27<=23.98 PASS 5280 12.40<=23.98 PASS 5320 11.88<=23.98 PASS 550010.66<=23.98 PASS 558010.80<=23.98 PASS 570012.78<=23.98 PASS 574514.59<=30 PASS 578514.89<=30 PASS 582514.39<=30 PASS 11N20 Ant1 51809.06<=23.98 PASS 52009.17<=23.98 PASS 52409.75<=23.98 PASS 5260 9.27<=23.98 PASS 5280 9.36<=23.98 PASS 5320 8.87<=23.98 PASS 55008.81<=23.98 PASS 55808.94<=23.98 PASS 570010.89<=23.98 PASS 574512.76<=30 PASS 578513.07<=30 PASS 582512.73<=30 PASS 11N40 Ant1 51907.11<=23.98 PASS 52308.77<=23.98 PASS 5270 6.14 <=23.98 PASS 5310 7.64 <=23.98 PASS 55109.84<=23.98 PASS 55509.89<=23.98 PASS 567010.70<=23.98 PASS 575513.46<=30 PASS 579513.39<=30 PASS 11AC20 Ant1 51808.01<=23.98 PASS 52008.23<=23.98 PASS 52408.79<=23.98 PASS 5260 8.29<=23.98 PASS 5280 8.39<=23.98 PASS 5320 7.86<=23.98 PASS 55007.44<=23.98 PASS 55807.57<=23.98 PASS 57009.54<=23.98 PASS 574511.43<=30 PASS 578511.75<=30 PASS 582511.26<=30 PASS 11AC40 Ant1 51908.57<=23.98 PASS 52309.19<=23.98 PASS 5270 8.73<=23.98 PASS 5310 8.37<=23.98 PASS 55108.60<=23.98 PASS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 103 of 150 55508.65<=23.98 PASS 56709.41<=23.98 PASS 575512.12<=30 PASS 579512.03<=30 PASS 11AC80 Ant1 52108.83<=23.98 PASS 52908.51<=23.98 PASS 55308.52<=23.98 PASS 56108.77<=23.98 PASS 577510.95<=30 PASS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 104 of 150 Appendix B-2 (ISEDC): Maximum output power Test Result 5150~5250MHz: Test Mode Antenna Channel Conducted output power [dBm] Antenna Gain EIRP Limit[dBm] Verdict (dBi) (dBm) 11A Ant1 5180 12.19 2 14.19 <=22.361 PASS 5200 12.23 2 14.23 <=22.401 PASS 5240 12.77 2 14.77 <=22.401 PASS 11N20 Ant1 5180 9.06 2 11.06 <=22.606 PASS 5200 9.17 2 11.17 <=22.615 PASS 5240 9.75 2 11.75 <=22.596 PASS 11N40 Ant1 5190 8.83 2 10.83 <=23.01 PASS 5230 8.51 2 10.51 <=23.01 PASS 11AC20 Ant1 5180 8.01 2 10.01 <=22.606 PASS 5200 8.23 2 10.23 <=22.615 PASS 5240 8.79 2 10.79 <=22.606 PASS 11AC40 Ant1 5190 5.96 2 7.96 <=23.01 PASS 5230 7.62 2 9.62 <=23.01 PASS 11AC80 Ant1 5210 8.83 2 10.83 <=23.01 PASS 5250~5350MHz: Test Mode Antenna Channel Conducted output power [dBm] Limit [dBm] Antenna Gain EIRP EIRP Limit Verdict (dBi) (dBm)[dBm] 11A Ant1 5260 12.27 <=23.39 2 14.27<=29.39 PASS 5280 12.40 <=23.37 2 14.4 <=29.37 PASS 5320 11.88 <=23.39 2 13.88<=29.39 PASS 11N20 Ant1 5260 9.27 <=23.61 2 11.27<=29.61 PASS 5280 9.36 <=23.61 2 11.36<=29.61 PASS 5320 8.87 <=23.60 2 10.87<=29.60 PASS 11N40 Ant1 5270 8.73 <=23.98 2 10.73<=30 PASS 5310 8.37 <=23.98 2 10.37<=30 PASS 11AC20 Ant1 5260 8.29 <=23.61 2 10.29<=29.61 PASS 5280 8.39 <=23.61 2 10.39<=29.61 PASS 5320 7.86 <=23.60 2 9.86 <=29.60 PASS 11AC40 Ant1 5270 6.3 <=23.98 2 8.3 <=30 PASS 5310 7.81 <=23.98 2 9.81 <=30 PASS 11AC80 Ant1 5290 8.51 <=23.98 2 10.51<=30 PASS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200811006B FCC Part 15.407 RSS-GEN Issue 5, March 2019 Amendment 1, RSS-247, Issue 2, February 2017 Page 105 of 150 5470-5725MHz: Test Mode Antenna Channel Conducted output power [dBm] Limit [dBm] Antenna Gain EIRP EIRP Limit Verdict (dBi) (dBm) [dBm] 11A Ant1 5500 10.66 <=23.392 12.66 <=29.39 PASS 5580 10.8 <=23.402 12.8 <=29.40 PASS 5700 12.78 <=23.392 14.78 <=29.39 PASS 11N20 Ant1 5500 8.81 <=23.622 10.81 <=29.62 PASS 5580 8.94 <=23.612 10.94 <=29.61 PASS 5700 10.89 <=23.612 12.89 <=29.61 PASS 11N40 Ant1 5510 9.84 <=23.982 11.84 <=30 PASS 5550 9.89 <=23.982 11.89 <=30 PASS 5670 10.7 <=23.982 12.7 <=30 PASS 11AC20 Ant1 5500 7.44 <=23.622 9.44 <=29.62 PASS 5580 7.57 <=23.622 9.57 <=29.62 PASS 5700 9.54 <=23.622 11.54 <=29.62 PASS 11AC40 Ant1 5510 8.6 <=23.982 10.6 <=30 PASS 5550 8.65 <=23.982 10.…

Text truncated - open the document above for the full version.

FCC PART 15.407 DYNAMIC FREQUENCY SELECTION TEST REPORT For VTech Telecommunications Ltd 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong FCC ID: EW780-H0E4-06 Report Type: Original Report Product Type: SIP Cordless Hotel Telephone Report Number: RSZ200811007-00A Report Date: 2020-09-11 Reviewed By: Jerry Zhang EMC Manager Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ200811007-00A FCC Part 15.407 DFS Test Report Page 2 of 20 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 TEST METHODOLOGY .................................................................................................................................................. 3 TEST FACILITY ............................................................................................................................................................. 4 DECLARATIONS ............................................................................................................................................................ 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL CABLE ..................................................................…

Text truncated - open the document above for the full version.