FBR5820Low Power BLE Transceiver

Fleetwood Group, Inc. 11832 James St. Holland, MI 49424 Phone: 616-396-1142 www.fleetwoodgroup.com TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 Date: 9/9/2025 Pursuant to FCC 22-84 Report and Order and KDB 986446 D01 Covered Equipment v01, the Commission adopted new FCC requirements to protect the nation’s networks and supply chains from equipment that poses an unacceptable risk to national security or the safety of U.S. persons. Specifically, the Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List. Certifications FCC ID: FBR5820 concerning “covered” equipment. Section 2.911(d)(5)(i)-(ii). Fleetwood Group, Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Fleetwood Group, Inc. (“the applicant”) certifies that the equipment for which authorization is sought does not contain software listed on the “covered” list which is prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Fleetwood Group, Inc. certifies that as of the date of the filing of the application, the applicant is not identified on the covered list as an entity producing covered equipment. Thank you. Regards, Signature: Date: 9/9/2025 Signed by (printed name): Brian Harvey

Fleetwood Group, Inc. 11832 James St. Holland, MI 49424 Phone: 616-396-1142 www.fleetwoodgroup.com TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 Date 9/10/2025 Pursuant to FCC 22-84 Report and Order and KDB 986446 D01 Covered Equipment v01, the Commission adopted new FCC requirements to protect the nation’s networks and supply chains from equipment that poses an unacceptable risk to national security or the safety of U.S. persons. Specifically, the Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List. Certification designating a U.S. agent for service of process. As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. 1. Be signed by both the applicant and the designated agent for service of process if the agent is different from the applicant. 2. Fleetwood Group, Inc. (“the applicant”) consent to accept the service of process. Brian Harvey 11832 James St. Holland, MI 49424 [email protected] 3. FRN number 0006745475 Fleetwood Group, Inc. acknowledges to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. If the agent changes then the TCB and the FCC must be notified. Regards, Signature: Date: 9/10/2025 Signed by (printed name): Brian Harvey

Fleetwood Group, Inc. 11832 James St. Holland, MI 49424 Phone: 616-396-1142 www.fleetwoodgroup.com TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 ATTENTION: Federal Communication Commission Equipment Authorization To whom it may concern, We would like to submit for Certification to FCC: FBR5820. Please find in the following application all related documentation to support this New Single Certification. We would appreciate your prompt attention to the submittal. Applicant Company name: Fleetwood Group, Inc. Contact Name: Brian Harvey Address: 11832 James St. Holland, MI 49424 Telephone No: 616-396-1142 Fax No: 616-820-8300 Email: [email protected] FCC ID Number: FBR5820 Signature: Date: 9/8/2025 Signed by (printed name): Brian Harvey

Fleetwood Group, Inc. 11832 James St. Holland, MI 49424 Phone: 616-396-1142 www.fleetwoodgroup.com Date: 9/8/2025 Subject: Confidentiality Request for: FBR5820 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual Fleetwood Group, Inc. has spent a substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ELITE ELECTRONIC ENGINEERING, INC. in the event information regarding the product or the product is made available to the public. ELITE ELECTRONIC ENGINEERING, INC. will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________________________ Brian T. Harvey VP Engineering, Electronics (Print name) (Signature/Title)

Fleetwood Group, Inc. 11832 James St. Holland, MI 49424 Phone: 616-396-1142 www.fleetwoodgroup.com TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 Date: 9/8/2025 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 To Whom It May Concern: Elite Electronic Engineering, Inc. is authorized to act on our behalf, until otherwise notified, for applications to Elite Electronic Engineering, Inc. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b) to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you. Regards, Signature: Date: 9/8/2025 Signed by (printed name): Brian T. Harvey

Engineering Test Report No. 2401638-03 Report Date August 21, 2025 Manufacturer Name Fleetwood Group Inc Manufacturer Address 11832 James Street Holland, MI 49424 Product Name Brand/Model No. V240S Date Received August 19, 2025 Assessment Dates August 21, 2025 Specifications FCC "Code of Federal Regulations" Title 47 Part 1, Subpart I FCC 447498 D04 Interim General RF Exposure Guidance v01 RSS-102 Issue 6 Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 Signature Tested by Javier Cardenas Signature Approved by Raymond J. Klouda, Re gistered Professional Engineer of Illinois – 44894 PO Number P63987 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. The data presented in this test report pertains to the EUT on the test dates specified. Additionaly, the assessment results presented in this test report are only valid at the separation distance(s) stated in section 8. The results in this test report shall not be used to claim product exemption or comformity at separation distances not covered in this report. Any electrical or mechanical modifications made to the EUT subsequent to the specified test date will serve to invalidate the data and void this certification. This report must not be used to claim product certification, approval, or endorsement by A2LA, NIST, or any agency of the Federal Government. Engineering Test Report No. 2401638-03 This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Page 2 of 20 Table of Contents 1. Report Revision History ........................................................................................................................... 3 2. Introduction .............................................................................................................................................. 4 3. Subject of Investigation ............................................................................................................................ 4 4. Standards and Requirements .................................................................................................................. 4 5. Sample Calculations ................................................................................................................................ 4 6. Photographs of EUT ................................................................................................................................ 5 7. Limits and Requirements ......................................................................................................................... 6 7.1. Requirements mandated by the FCC ...................................................................................................... 6 7.2. Requirements mandated by Innovation, Science and Economic Development Canada ........................ 7 8. Assessment Results ................................................................................................................................ 8 8.1. RF Exposure Evaluation Pertinent to the Requirements of the FCC of a Single RF Source .................. 8 8.2. RF Exposure Evaluation Relevant to the Requirements of the ISED of a Single RF Source ................. 9 9. Statement of Compliance ......................................................................................................................... 9 10. Scope of Accreditation ........................................................................................................................... 10 Engineering Test Report No. 2401638-03 Page 3 of 20 1. Report Revision History Revision Date Description – 22 AUG 2025 Initial Release of Engineering Test Report No. 2401638-03 Engineering Test Report No. 2401638-03 Page 4 of 20 2. Introduction The FCC, Innovation, Science and Economic Development Canada, European Union and Australia/New Zealand publish standards regarding the evaluation of the RF Exposure hazard of radio communications devices. An evaluation has been performed on the Fleetwood Group Inc Hydra IR Sensing Hub with BLE Beacon, Model No. V240S pursuant to the relevant requirements. 3. Subject of Investigation This document presents the demonstration of RF Exposure compliance on a Hydra IR Sensing Hub with BLE Beacon, (hereinafter referred to as the Equipment under Test (EUT)). The EUT was identified as follows: EUT Identification Description Hydra IR Sensing Hub with BLE Beacon Model/Part No. V240S The EUT is capable of operating in the following bands of the radio spectrum: Radio Spectrum Bands of Operation BLE Ex. 2400MHz to 2483.5MHz 4. Standards and Requirements The tests were performed to selected portions of, and in accordance with the following specifications. • Federal Communications Commission "Code of Federal Regulations", Title 47, Chapter I, Subchapter A, …

Text truncated - open the document above for the full version.

- Midmark IR 3.0 - FCC Antenna Gain Information 1 1 DESCRIPTION For FCC/IC certification, the following information will be provided: 1. Type of antenna being used 2. Construction of the antenna 3. Antenna gain vs frequency 4. Polar plots of the antenna pattern These will be laid out in the sections to follow. All these values are from simulations. 2 TYPE OF ANTENNA AND CONSTRUCTION The antenna is a printed inverted L antenna. The construction is of copper on the first layer of a PCB. The layers underneath the antenna are removed. Dimensions are shown in Figure 1 Antenna Construction. Note: Length of ground plane is 109.8mm from the top left corner of the ground plane. Figure 1 Antenna Construction Figure 2: Antenna Tuning Network 2 3 ANTENNA GAIN VS FREQUENCY Figure 3: Antenna Realized Gain over Frequency 4 POLAR PLOTS AT 2.45 GHZ Use Figure 4 as a reference for Theta and Phi for the cuts. Cuts are seen Figure 5 to Figure 7 Figure 4: 3D Gain Plot, including Phi and Theta indicators 3 Figure 5:Theta = 90° Realized Gain over Phi Figure 6: Phi = 90 ° Realized Gain over Theta 4 Figure 7: Phi = 90° Realized Gain over Theta

Engineering Test Report No. 2401638-01 Report Date August 20, 2025 Manufacturer Name Fleetwood Group Inc Manufacturer Address 11832 James Street Holland, MI 49424 Test Item Name Model No. Hydra IR Sensing Hub with BLE Beacon V240S Date Received August 19, 2025 Test Dates August 19, 2025 through August 20, 2025 Specifications FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C, Section 15.247 Innovation, Science, and Economic Development Canada, RSS-247 Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 FCC Reg. Number: 269750 IC Reg. Number: 2987A CAB Identifier: US0107 Signature Tested by Javier Cardenas Signature Approved by Raymond J. Klouda, Re gistered Professional Engineer of Illinois – 44894 PO Number P63987 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Elite Electronic Engineering Incorporated certifies that the information contained in this report was obtained under conditions which meet or exceed those specified in the FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C, Section 15.247 and Innovation, Science, and Economic Development Canada, RSS-247 test specifications. The data presented in this test report pertains to the EUT on the test dates specified. Any electrical or mechanical modifications made to the EUT subsequent to the specified test date will serve to invalidate the data and void this certification. This report must not be used to claim product certification, approval, or endorsement by A2LA, NIST, or any agency of the Federal Government. Engineering Test Report No. 2401638-01 This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Page 2 of 67 Table of Contents 1. Report Revision History ........................................................................................................................... 3 2. Introduction .............................................................................................................................................. 4 2.1. Scope of Tests ......................................................................................................................................... 4 2.2. Purpose .................................................................................................................................................... 4 2.3. Identification of the EUT ........................................................................................................................... 4 3. Power Input .............................................................................................................................................. 4 4. Grounding ................................................................................................................................................ 4 5. Support Equipment .................................................................................................................................. 4 6. Interconnect Leads .................................................................................................................................. 4 7. Modifications Made to the EUT ................................................................................................................ 5 8. Modes of Operation ................................................................................................................................. 5 8.1. Tx ............................................................................................................................................................. 5 9. Test Specifications ................................................................................................................................... 5 10. Test Plan .................................................................................................................................................. 5 11. Deviation, Additions to, or Exclusions from Test Specifications .............................................................. 5 12. Laboratory Conditions .............................................................................................................................. 5 13. Summary .................................................................................................................................................. 6 14. Sample Calculations ................................................................................................................................ 6 15. Statement of Conformity .......................................................................................................................... 7 16. Certification .............................................................................................…

Text truncated - open the document above for the full version.