FHO-L2006LED light panel

1 MISSMYRA 2AA-2237686-1 English IMPORTANT SAFETY INSTRUCTIONS For indoor use only. Regularly check the cord, the transformer and all other parts for damage. If any part is damaged the product should not be used. Important information! Keep these instructions for future use. CAUTION! The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes. Do not immerse in water. Cleaning Use a damp cloth, never a strong cleaning agent. 3 English CAUTION To reduce the risk of fire, electric shock, or injury to persons: Use only insulated staples or plastic ties to secure cords. Route and secure cords so that they will not be pinched or damaged when the cabinet is pushed to the wall. Position the portable cabinet light with respect to the cabinet so the lamp replacement markings can be read during relamping. Not intended for recessed installation in ceilings, or soffits. The low- voltage portable cabinet light may be installed inside or under a kitchen cabinet or other built-in furniture when: 1. The low-voltage Class 2 power supply is located outside the cabinet and is not concealed; and 2. The line voltage power supply cord is not concealed or run through openings in the cabinet, walls, ceilings, or floors. This requirement does not apply to the wiring between the cabinet light and the power unit. The National Electric Code (NEC) does not permit cords to be concealed where damage to insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible for examination. Cords should be visually examined periodically and immediately replaced when any damage is noted. 4AA-2237686-1 English ATTENTION: CAUTION: Injury to persons and damage to the lamp and/or the mounting surface may result if the lamp is pulled from the surface. To reduce the likelihood of such injury or damage, mount only on a surface that is mechanically sound. English WARNING Deviation from the assembly instructions may result in a risk of fire or electric shock. 5 6AA-2237686-1 English 1. Wipe the surface dry where the tape will be used with a clean and dry cloth. 2. The assembly tape is permanent and is not intended to be removed. You might damage the surface under the lamp if you try to remove the tape. 3. Please keep the unused fittings for future use. English WARNING – Strangulation hazard. NEVER place cord within reach of the child in a cot or playpen. ALWAYS secure cord to wall or cabinet. Check regularly that the cord is securely fastened. Pull the cord to remove any slack between fasteners. Tie up any remaining slack cord between driver and socket. 7 Français CONSIGNES DE SÉCURITÉ IMPORTANTES Uniquement pour une utilisation en intérieur. Vérifier régulièrement que le câble, le transformateur et les autres parties ne sont pas endommagés. Si l’une de ces pièces est endommagée, ne pas utiliser le produit. Information importante. Conserver la notice pour tout utilisation ultérieure. MISE EN GARDE La source lumineuse du produit est composée de diodes (LED) qui ne se remplacent pas. Ne jamais démonter le produit, les diodes peuvent causer des blessures aux yeux. Ne jamais immerger dans de l’eau. Entretien Nettoyer à l’aide d’un chiffon humide, éviter les détergents puissants. 8AA-2237686-1 Français ATTENTION! Pour réduire le risque d’incendie, d’électrocution ou de blessure, utiliser uniquement des agrafes isolées ou des liens en plastique pour fixer les câbles. Faire passer et fixer les câbles de manière à ce qu’ils ne soient pas coincés ou endommagés lorsque le meuble est poussé contre le mur. Placer l’éclairage portatif de sorte que les informations concernant le remplacement de la source de lumière puissent être relevées. Ne doit pas être installé dans une corniche ou renfoncement de plafond. L’éclairage portatif basse tension peut être installé à l’intérieur ou sous un meuble de cuisine (ou un autre meuble encastré) à condition que: 1. l’alimentation basse tension Classe 2 soit située hors de l’élément et ne soit pas dissimulée 2. le câble d’alimentation ne soit pas dissimulé et qu’il ne passe pas à travers des ouvertures dans le meuble, les murs, le plafond ou le sol. Cette exigence ne s’applique pas au câble entre l’éclairage du meuble et le bloc d’alimentation. Le Code Electrique National (NEC) ne permet pas qu’un câble dont l’isolation risque d’être endommagée soit dissimulé. Pour éviter tout risque d’incendie, ne pas dissimuler le câble à l’intérieur d’un mur, d’un plafond, d’une corniche, d’un meuble de cuisine etc. si cela rend la vérification de l’état du câble plus difficile. Vérifier régulièrement l’état des câbles. Si un câble est endommagé, il doit être remplacé immédiatement. 9 Français IMPORTANT! MISE EN GARDE Ne pas arracher le luminaire. Cela peut provoquer des blessures ou l’endommagement du luminaire ou du support auquel il est fixé. Pour des raisons de sécurité, fixer le luminaire à une surface solide et adaptée. Français ATTENTION Tout écart par rapport aux instructions d’assemblage peut entraîner un risque d’incendie ou de choc électrique. 10AA-2237686-1 11 Français 1. Bien sécher la surface où le ruban adhésif va être utilisé à l’aide d’un chiffon propre et sec. 2. Le ruban de montage est permanent et ne doit pas être retiré. Décoller le ruban adhésif risque d’abîmer le dessous de la lampe. 3. Conserver les fixations inutilisées pour un usage ultérieur. Français ATTENTION - Risque d’étranglement Ne JAMAIS fixer le fil à portée de main d’un enfant dans un lit bébé ou dans un parc. TOUJOURS immobiliser le fil au mur ou au rangement. Vérifier régulièrement que le fil est correctement maintenu. Tendre le fil pour éviter tout jeu entre deux fermetures. Rassembler et attacher tout fil restant entre la fixation et la prise de courant. 12AA-2237686-1 Español INSTRUCCIONES IMPORTANTES DE SEGURIDAD Sólo para uso en interiores. Comprobar el cable, el tra…

Text truncated - open the document above for the full version.

English This device complies with Part 15 of the FCC Rules. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation Science and Economic Development Canada's licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the quipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Français Ce dispositif est conforme à la section 15 des règlements de la FCC. Ce dispositif contient un ou plusieurs émetteurs/récepteurs sans licence qui sont conformes à la ou aux normes RSS sans licence d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer d'interférences nuisibles, et (2) cet appareil doit accepter toute autre interférence reçue, y compris les interférences pouvant entraîner un fonctionnement non désiré. ATTENTION : Tout changement ou modification apportés à cet appareil sans approbation expresse de la partie responsable de la conformité peut rendre nulle la capacité de l’utilisateur à utiliser cet appareil. REMARQUE : Cet appareil a été testé et il est conforme aux exigences relatives aux appareils électroniques de classe B, selon la section 15 des règles de la FCC (Commission fédérale des communications). Ces exigences sont prévues pour fournir une protection raisonnable contre les interférences nuisibles dans le cas d’une installation domestique. Cet appareil génère, utilise et peut émettre de l’énergie sous forme de fréquences radio. Si l’appareil n’est pas installé ou utilisé conformément aux instructions, il peut provoquer des interférences perturbant les communications radio. Il est cependant impossible de garantir l’absence totale d’interférences d’une installation donnée. Si cet appareil produit des interférences nuisibles à la réception radio/télévision, ce qui peut-être déterminé en mettant successivement l’appareil sous tension et hors tension, nous conseillons à l’utilisateur d’essayer de remédier à ce problème en suivant l’une des procédures suivantes : • Réorienter ou déplacer l’antenne de réception. • Augmenter la distance entre l’appareil et le récepteur. • Brancher l’appareil à une prise placée sur un circuit différent de celui auquel le récepteur est raccordé. • Contacter votre revendeur ou tout technicien radio/TV qualifié pour obtenir de l’aide. Español Este dispositivo cumple la parte 15 de la normativa de la FCC. Este dispositivo contiene transmisores/ receptores exentos de licencia que cumplen las normas RSS de exención de licencia del Innovation Science and Economic Development Canada. El funcionamiento está sujeto a las dos condiciones siguientes: (1) Este dispositivo no puede provocar interferencias dañinas, y (2) Este dispositivo debe aceptar cualquier interferencia recibida, incluida la interferencia que pueda provocar un funcionamiento no deseado del dispositivo. ATENCIÓN: Cualquier cambio o modificación que se realice en este aparato sin la aprobación expresa de la parte responsable de la conformidad puede anular la capacidad del usuario para utilizar el aparato. NOTA: Este equipo ha sido probado para comprobar que cumple los límites establecidos en los dispositivos digitales de Clase B, según el apartado 15 del reglamento FCC. Estos límites se han establecido para proporcionar una protección razonable contra las interferencias perjudiciales en una instalación doméstica. Este equipo genera, usa e irradia energía de radiofrecuencia, y si no se instala y se usa de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las comunicaciones por radio. Sin embargo no existe garantía de que no se produzcan interferencias en una instalación en concreto. Si el equipo produjera interferencias perjudiciales en la recepción de radio o TV, lo que se puede comprobar encendiendo y apagando el equipo, recomendamos al usuario que intente corregir dichas interferencias adoptando una o más de las siguientes medidas: • Reorientar o recolocar la antena receptora. • Aumentar la distancia entre el equipo y el receptor. • Conectar el equipo a un enchufe o circuito distinto al que esté conectado el receptor. • Solicitar ayuda al vendedor o a un técnico cualificado de radio/TV.

© Inter IKEA Systems B.V. 2014 June 2 nd , 2020 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement IKEA of Sweden AB FCC ID: FHO-L2006 To Whom It May Concern: We, IKEA of Sweden AB, hereby authorized Intertek Semko AB, Swedens to act as our Agent for the purpose of preparing application for FCC ID number FHO- L2006 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is May 5th, 2020. The Limited Agency Agreement expires on November 5th , 2020, unless sooner terminated or extended by written notice to Intertek Semko AB, Sweden and the Federal Communications Commission. This i s to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Ivan Susak Team Manager, Laws&Standards IKEA of Sweden AB [email protected] +4647681000

© Inter IKEA Systems B.V. 2014 August 25, 2020 Attention: Application Examiner RE: Request for Confidentiality Applicant: IKEA of Sweden AB FCC ID: FHO-L2006 To Whom It May Concern: Permanent Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: •Schematics •Detailed Block Diagrams •Detailed Operational/Functional Description Short-term Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization: •Test setup photos •External photos •Internal photos •User Manual Rationale for request for confidentiality: IKEA of Sweden AB has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential © Inter IKEA Systems B.V. 2014 porti ons of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] Sincerely, Ivan Susak Team Manager –Laws & standards IKEA of Sweden AB [email protected] +4647681000

Revision 1 Revision Comment Added accessories No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 1 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - External pictures NA Product Name MISSMYRA Doc number 2244621 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Revision 1 Revision Comment Added accessories No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 2 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - External pictures NA Product Name MISSMYRA Doc number 2244621 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Revision 1 Revision Comment Added accessories No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 3 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - External pictures NA Product Name MISSMYRA Doc number 2244621 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Photo of mounting accessories Revision 1 Revision Comment No. of Changes Checked by Approved by Elias Molin (elmol8) Approved date 2019-11-14 Designed by IKEA of Sweden No. of Pages 1 (1) Tolerance Replaces document Description Integrated Lighting ♦ ♦ _____________________________________________________________________________________ Name SKYDRAG - Placement of Type label Product Name - Doc number 2210181 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or com-municated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Placement of the Label

Test report no. 2020947STO-102 Annex 1 Page 1 (3) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se ANNEX 1 Photos of EUT EUT Photos of test setup Test setup for conducted emission 150 kHz – 30 MHz, 30W Test report no. 2020947STO-102 Annex 1 Page 2 (3) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test setup for conducted emission 150 kHz – 30 MHz, 10W Test set up radiated emission 30 MHz – 1 GHz, 30W Test report no. 2020947STO-102 Annex 1 Page 3 (3) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test set up radiated emission 30 MHz – 1 GHz, 10W

Type No. L2006 Made in 00000 Missmyra TYP L2006 NA Version 3 Conforms to: UL Std 2108 Certified to: CSA Std C22.2 No 9.0 CAN ICES-005 (B) / NMB-005 (B) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Sup. No. FCC ID: FHO-L2006 ??????? Label size: 80x40mm

Revision 1 Revision Comment No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 1 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - Internal pictures NA Product Name MISSMYRA Doc number 2244628 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Revision 1 Revision Comment No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 2 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - Internal pictures NA Product Name MISSMYRA Doc number 2244628 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Revision 1 Revision Comment No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 3 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - Internal pictures NA Product Name MISSMYRA Doc number 2244628 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE

Test report No. 2020947STO-101 Page 2 (20) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.05 Revision History Test report number Date Description Changes 2010962STO-103 17 April, 2020 First release - 2020947STO-101 11 June, 2020 First release Updated marking plate. This document replaces test report 2010962STO-103. Test report No. 2020947STO-101 Page 3 (20) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.05 CONTENTS Page 1. Client Information ............................................................................................................... 4 2. Equipment under test (EUT) ............................................................................................... 4 2.1 Identification of the EUT ........................................................................................... 4 2.2 Test set up and EUT photos .................................................................................... 6 2.3 Additional information about the EUT ...................................................................... 6 3. Test Specifications ............................................................................................................. 7 3.1 Standards ................................................................................................................. 7 3.2 Test site .................................................................................................................... 7 3.3 Mode of operation during the test ............................................................................ 7 3.4 Compliance .............................................................................................................. 8 4. Test Summary .................................................................................................................... 9 5. Conducted continuous disturbances ................................................................................ 10 5.1 Operating environment ........................................................................................... 10 5.2 Test setup and test procedure ............................................................................... 10 5.3 Measurement uncertainty ....................................................................................... 10 5.4 Test results, AC Power input port, Class B, 30W, Maximum light ......................... 10 5.5 Test results, AC Power input port, Class B, 30W, Minimum light .......................... 11 5.6 Test results, AC Power input port, Class B, 10W, Maximum light ......................... 12 5.7 Test results, AC Power input port, Class B, 10W, Minimum light .......................... 13 5.8 Test equipment ...................................................................................................... 14 6. Radiated rf Emission in the frequency-range 30 MHz – 1 GHz ....................................... 15 6.1 Operating environment ........................................................................................... 15 6.2 Test setup and test procedure ............................................................................... 15 6.3 Test conditions ....................................................................................................... 15 6.4 Measurement uncertainty ....................................................................................... 15 6.5 Test results, 30 – 1000 MHz, FCC and ICES-001 Group 1, Class B, 30 W, Maximum light ................................................................................................................. 16 6.6 Test results, 30 – 1000 MHz, FCC and ICES-001 Group 1, Class B, 30 W, Minimum light .................................................................................................................. 17 6.7 Test results, 30 – 1000 MHz, FCC and ICES-001 Group 1, Class B, 10 W, Maximum light ................................................................................................................. 18 6.8 Test results, 30 – 1000 MHz, FCC and ICES-001 Group 1, Class B, 10 W, Minimum light .................................................................................................................. 19 6.9 Test equipment ...................................................................................................... 20 Test report No. 2020947STO-101 Page 4 (20) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.05 1. CLIENT INFORMATION The EUT has been tested by request of Company IKEA of Sweden AB Box 702 343 81 Älmhult Sweden Name of contact Markus Mauritzon 2. EQUIPMENT UNDER TEST (EUT) 2.1 Identification of the EUT Equipment Luminaire for furniture with LED Type/Model L2006 Missmyra Brand name Serial number IKEA - Manufacturer IKEA of Sweden AB Rating Luminaire: 24 V DC, 5.6 W Driver 10 W: AC Input: 100-120 V AC, 50/60 Hz DC Output: 24 V DC, 0-0.42 A, 10 W max Driver 30 W: AC Input: 100-120 V AC, 50/60 Hz DC Output: 24 V DC, 0-1.25 A, 30 W max Class Luminaire: III Driver: II Highest clock frequency < 108 MHz FCC ID FHO-L2006 Test report No. 2020947STO-101 Page 5 (20) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.05 Rating plates Test report No. 2020947STO-101 Page 6 (20) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.05 2.2 Test set up and EUT photos Test set up and EUT photos are enclosed in Annex 1 No. 2020947STO-102 to this report. 2.3 Additional information about the EUT The EUT was tested in a tabletop configuration. The EUT was equipped with the following cable: Port Type Length [m] Specifications DC power cable - 3,5 - 2.4 Peripheral Equipment Peripheral equipment is equipment needed for correct operation of the EUT, but not included as a part of the testing and evaluation of the EUT. Un…

Text truncated - open the document above for the full version.

Revision 1 Revision Comment No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 1 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - Test setup photos NA Product Name MISSMYRA Doc number 2244630 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Test setup for conducted emission Revision 1 Revision Comment No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 2 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - Test setup photos NA Product Name MISSMYRA Doc number 2244630 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE Test setup for radiated emission Revision 1 Revision Comment No. of Changes Checked by Approved by Magnus Heurlin (maheu) Approved date 2020-06-02 Designed by IKEA of Sweden No. of Pages 3 (3) Tolerance Replaces document Description Integrated Lighting ♦ Wardrobe lighting ♦ _____________________________________________________________________________________ Name L2006 - Test setup photos NA Product Name MISSMYRA Doc number 2244630 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual property rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.1 MEASURED IMAGE