FHO-LED1805E22LED light engine

LED1805E22 English Français Español 6 9 14 ADD LIGHT SOURCES TO YOUR STEERING DEVICE: Before you can use your light source you’ll need to pair it with a steering device. To add more light sources, just repeat the steps below: 1. Make sure that your light source is installed and the main power switch is turned on. 2. Hold the steering device close to the light source you want to add (no more than 5 cm away). 3. Press and hold the pairing button for at least 10 seconds. A red light will shine steadily on the steering device. Your light source will begin to dim and finally flash one time to indicate that it has been successfully paired. Up to 10 light sources can be paired with 1 steering device. Make sure to pair them one at a time. If the light sources are close to each other, disconnect those that have already been paired from the main power switch. CAUTION: DO NOT USE WITH STANDARD DIMMERS. Only use the English4 control provided with or specified by these instructions to control this bulb. This bulb will not operate properly when connected to a standard (incandescent) dimmer or dimming control. Only controllable by IKEA Smart lighting products. The colour temperature can be switched between 2200K (warm glow), 2700K (warm white) and 4000K (cool white). RESET YOUR DEVICE Toggle the main switch 6 times. TECHNICAL DATA Type: LED1805E22 Input: 110-120 Vac, 60Hz Range: 10 m in open air Operating frequency: 2405-2480MHz Output power: 10 dBm Manufacturer: IKEA of Sweden AB Address: Box 702, SE-343 81, Älmhult, SWEDEN 5 This device complies with Part 15 of the FCC Rules/ Innovation Science and Economic Development Canada's licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 6 This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. RF EXPOSURE INFORMATION According to RF exposure regulations, under normal operations the end user shall refrain from being closer than 20 cm from the device. 7 License rights and limitations NO RIGHTS OR LICENSES, EXPRESS OR IMPLIED, ARE GRANTED TO USE THIRD-PARTY DEVICES IN COMBINATION WITH THESE PRODUCTS IN A WIRELESS MESH NETWORK, OR TO USE THIRD-PARTY SERVICES TO ACCESS, MONITOR OR CONTROL THESE PRODUCTS IN A WIRELESS MESH NEWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK. For use pursuant to U.S. Patent Nos.: US 6,914,893 , US 7,697,492 , US 8,964,708 The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store. 8 9 AJOUT SOURCES LUMINEUSES AU DISPOSITIF DE COMMANDE Avant d’utiliser votre source lumineuse, elle doit être couplée avec un dispositif de commande. Pour ajouter d’autres sources lumineuses, il suffit de répéter les étapes ci-dessous : 1. S’assurer que la source lumineuse est installée et allumée. 2. Maintenir le dispositif de commande à proximité (pas plus de 5 cm) de la source lumineuse à ajouter. 3. Appuyer sur le bouton de couplage et le maintenir enfoncé au moins 10 secondes. Un voyant à LED rouge s’allume de manière continue sur le dispositif de commande. La source lumineuse baissera en intensité et clignotera une fois pour indiquer que le couplage est réussi. Il est possible de coupler jusqu’à 10 sources lumineuses à 1 dispositif de commande. Veiller à les coupler l’une après l’autre. Si les sources lumineuses sont proches les unes des autres, débrancher de l’alimentation générale celles qui ont déjà été couplées. Français MISE EN GARDE : NE PAS UTILISER AVEC DES VARIATEURS D'INTENSITÉ STANDARD. Pour régler l'intensité lumineuse de cette ampoule, utiliser uniquement le dispositif de réglage fourni avec le produit ou mentionné dans les présentes instructions. Cette ampoule ne peut fonctionner correctement si elle est connectée à un variateur d'intensité standard (à incandescence). Cette ampoule ne peut fonctionner qu'avec les produits de la gamme éclairage connecté IKEA. La couleur de la lumière varie entre 2 200 Kelvin (rougeâtre), 2 700 Kelvin (blanc chaud) et 4 000 Kelvin (blanc froid). RÉINITIALISER L’APPAREIL Actionner l’interrupteur principal 6 fois. CARACTÉRISTIQUES TECHNIQUES Type : LED1805E22 Entrée : 110-120 Vac, 60Hz Portée : 10 m en champ libre. 10 11 Fréquence de transmission : 2405-2480MHz Puissance de sortie radio : 10 …

Text truncated - open the document above for the full version.

© Inter IKEA Systems B.V. 2014 January 9 , 2020 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement IKEA of Sweden AB FCC ID: FHO-LED1805E22 To Whom It May Concern: We, IKEA of Sweden AB, hereby authorized Intertek Semko AB, Sweden to act as our Agent for the purpose of preparing application for FCC ID number FHO- LED1805E22 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is January 9 , 2020. The Limited Agency Agreement expires on Februari 29 th , 2020, unless sooner terminated or extended by written notice to Intertek Semko AB, Sweden and the Federal Communications Commission. This i s to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant i s not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Ivan Susak Team Manager, Laws&Standards IKEA of Sweden AB [email protected] +4647681000

© Inter IKEA Systems B.V. 2014 Aug 21, 2019 Attention: Application Examiner RE: Request for Confidentiality Applicant: IKEA of Sweden AB FCC ID: FHO-LED1805E22 To Whom It May Concern: Permanent Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: • Schematics • Detailed Block Diagrams • Detailed Operational/Functional Description Short-term Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization: • Test setup photos • External photos • Internal photos Rationale for request for confidentiality: IKEA of Sweden AB has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential © Inter IKEA Systems B.V. 2014 portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] Sincerely, Ivan Susak Team Manager –Laws & standards IKEA of Sweden AB [email protected] +4647681000

Revision 1 Revision Comment No. of Changes Checked by Approved by Approved date Designed by IKEA of Sweden No. of Pages 1 (1) Tolerance Replaces document Description Light Bulbs and Tubes ♦ ♦ _____________________________________________________________________________________ Name LED1805E22 External photographs Product Name LIGHT ENGINE Doc number 2199595 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual prop-erty rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 MEASURED IMAGE IKEA of Sweden AB

Revision Comment Updated FCC information Approved by Jörgen Skoog (oogj) Approved date 2020-01-14 Description Light Bulbs and Tubes ו ו ______________________________________________ Name Label LED1805E22 NA Replaces document No. of Pages 1 (1) LIGHT ENGINE Doc number 2212952 Version 3.1 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and in-tellectual property rights and should, without written consent from IKEA, in no way be copied, re-produced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 DRAWING IKEA of Sweden AB

Revision 1 Revision Comment No. of Changes Checked by Approved by Approved date Designed by IKEA of Sweden No. of Pages 1 (3) Tolerance Replaces document Description Light Bulbs and Tubes ♦ ♦ _____________________________________________________________________________________ Name LED1805E22 Internal photographs Product Name LIGHT ENGINE Doc number 2199640 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual prop- erty rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 MEASURED IMAGE IKEA of Sweden AB Revision 1 Revision Comment No. of Changes Checked by Approved by Approved date Designed by IKEA of Sweden No. of Pages 2 (3) Tolerance Replaces document Description Light Bulbs and Tubes ♦ ♦ _____________________________________________________________________________________ Name LED1805E22 Internal photographs Product Name LIGHT ENGINE Doc number 2199640 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual prop- erty rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 MEASURED IMAGE IKEA of Sweden AB Revision 1 Revision Comment No. of Changes Checked by Approved by Approved date Designed by IKEA of Sweden No. of Pages 3 (3) Tolerance Replaces document Description Light Bulbs and Tubes ♦ ♦ _____________________________________________________________________________________ Name LED1805E22 Internal photographs Product Name LIGHT ENGINE Doc number 2199640 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual prop- erty rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 MEASURED IMAGE IKEA of Sweden AB

LED1805E22 - PCB Internal Photos

Test report No. 1907679STO-001, Ed. 2 Page 2 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 Revision History Edition Date Description Changes 1 May 24, 2019 First release 2 February 11, 2020 Second release The report was updated according to order number 2010438STO-101 Photos of EUT and test setups in annex 1. Test report No. 1907679STO-001, Ed. 2 Page 3 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 CONTENTS Page 1. Client Information ............................................................................................................. 4 2. Equipment under test (EUT)............................................................................................. 4 2.1 Identification of the EUT ........................................................................................... 4 2.2 Test set up and EUT photos .................................................................................... 4 2.3 Purpose of the test ................................................................................................... 5 2.4 Additional information about the EUT ...................................................................... 5 2.5 Modifications made to improve EMC-characteristics ............................................... 5 3. Test Specifications ........................................................................................................... 6 3.1 Standards ................................................................................................................. 6 3.2 Additions, deviations and exclusions from standards and accreditation ................. 6 3.3 Test site .................................................................................................................... 6 3.4 Mode of operation during the test ............................................................................ 6 3.5 Compliance .............................................................................................................. 7 4. Test Summary .................................................................................................................. 8 5. Conducted continuous disturbances ................................................................................ 9 5.1 Operating environment ............................................................................................. 9 5.2 Test set-up and test procedure ................................................................................ 9 5.3 Measurement uncertainty ......................................................................................... 9 5.4 Test results, AC Power input port, Class B, max luminous intensity ..................... 10 5.5 Test results, AC Power input port, Class B, min luminous intensity ...................... 11 5.6 Test equipment ...................................................................................................... 12 6. Radiated rf Emission in the frequency-range 30 MHz – 13 GHz ................................... 13 6.1 Operating environment ........................................................................................... 13 6.2 Test set-up and test procedure .............................................................................. 13 6.3 Test conditions ....................................................................................................... 13 6.4 Measurement uncertainty ....................................................................................... 14 6.5 Test results, 30 – 1000 MHz, Class B, max luminous intensity ............................. 15 6.6 Test results, 30 – 1000 MHz, Class B, min luminous intensity .............................. 16 6.7 Test equipment ...................................................................................................... 17 6.8 Test results, 1 – 13 GHz, Class B, max luminous intensity ................................... 18 6.9 Test results, 1 – 13 GHz, Class B, min luminous intensity .................................... 19 6.10 Test equipment ...................................................................................................... 19 Test report No. 1907679STO-001, Ed. 2 Page 4 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 1. CLIENT INFORMATION The EUT has been tested by request of Company IKEA of Sweden AB Box 702 343 81 Älmhult Sweden Name of contact Jörgen Skoog 2. EQUIPMENT UNDER TEST (EUT) 2.1 Identification of the EUT Equipment Self-ballasted LED-lamp Type/Model LED1805E22 Brand name Serial Number - Manufacturer IKEA of Sweden AB Rating 120 V, 60 Hz, max 25 W Class - Highest frequency 2405 – 2480 MHz Software version - Rating plate 2.2 Test set up and EUT photos Test set up and EUT photos are enclosed in Annex 1 to this test report. Test report No. 1907679STO-001, Ed. 2 Page 5 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 2.3 Purpose of the test The purpose of the tests was to verify that the EUT fulfills the requirements according to FCC 47 CFR Part 15: Radio frequency device, Subpart B: Unintentional radiators Class B and ICES- 005 Issue 5: Lighting Equipment, Class B. 2.4 Additional information about the EUT The EUT is a self-ballasted LED – lamp provided with a radio remote control for on/off, color setting and dimming. The EUT has the following noted components: radio module, type ICC-A-1 The EUT was tested in a tabletop configuration. The EUT was tested with the following cables Port Type Length [m] Specifications AC Mains Fixed connection - - 2.5 Modifications made to improve EMC-characteristics In order to comply with the requirements regarding radiated emission 30 – 1000 MHz, the electronic is slightly modified by the manufacturer. The modification of the electronic circuit consists of ad…

Text truncated - open the document above for the full version.

1 Appendix A – Photographs 2