FHO-T2011LED light Plafond

1 OSVALLA 2AA-2195664-1 ENGLISH INSTALLATION INSTRUCTIONS CAUTION: Before starting, turn off power at main circuit panel. ENGLISH CAUTION! The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes. Do not immerse in water. Cleaning Use a damp cloth, never a strong cleaning agent. ENGLISH This device complies with part 15 of the FCC Rules. Operation is subjected to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAVE THESE INSTRUCTIONS 3 FRANÇAIS INSTRUCTIONS D’INSTALLATION AT T ENT ION : Coupez l’alimentation avant de procéder à l’installation. FRANÇAIS MISE EN GARDE! La source lumineuse du produit est composée de diodes (LED) qui ne se remplacent pas. Ne jamais démonter le produit, les diodes peuvent causer des blessures aux yeux. Ne pas plonger dans l’eau. Entretien Utiliser un chiffon humide, jamais d’agent nettoyant puissant. FRANÇAIS Cet appareil est conforme à la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer de brouillage préjudiciable et 2. il doit accepter tout brouillage reçu, y compris le brouillage pouvant entraîner un mauvais fonctionnement. AT T ENT ION : Tout changement apporté à cet appareil non expressément approuvé par la partie responsable de la conformité est susceptible d’annuler le droit de l’utilisateur à se servir de cet équipement. NOTE: Cet équipement a été testé et déclaré conforme aux limites imposées aux appareils numériques de la classe B, en vertu de la partie 15 des règles de la FCC. Ces limites sont conçues pour assurer une protection suffisante contre les interférences nuisibles dans les installations résidentielles. Cet équipement génère, utilise et peut dégager de l’énergie de radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions du fabricant, provoquer un brouillage préjudiciable aux communications radio. Il n’existe toutefois aucune garantie qu’un équipement particulier ne sera pas victime de brouillage. Si cet équipement entraîne un brouillage préjudiciable à la réception des émissions radio ou de télévision, identifiable en mettant le terminal hors puis sous tension, il est recommandé à l’utilisateur de tenter de résoudre ce problème au moyen d’une ou plusieurs des mesures suivantes: - Orienter l’antenne réceptrice différemment ou la changer de place. - Augmenter la distance séparant l’équipement du récepteur. - Connecter l’appareil à une prise sur un circuit différent de celui auquel est branché le récepteur. Obtenir de l’aide auprès du revendeur ou d’un technicien radio/TV expérimenté. CONSERVER CES MESURES DE SÉCURITÉ 4AA-2195664-1 ESPAÑOL INSTRUCCIONES DE MONTAJE ADVERTENCIA: Antes de comenzar el montaje, cortar la luz en el cuadro general. ESPAÑOL ¡ AT ENCIÓN ! La fuente de luz de este producto son diodos de emisión de luz (LED) que no se reemplazan. No desmontes el producto, ya que la luz de los diodos puede dañar los ojos. No sumergir en agua. Limpieza Utiliza un paño humedecido, nunca detergentes fuertes. ESPAÑOL Este aparato cumple la parte 15 de las normas FCC. Su funcionamiento está sujeto a las dos condiciones siguientes: 1. Este aparato no debe provocar interferencias perjudiciales. 2. Debe aceptar cualquier interferencia que reciba, incluidas las interferencias que puedan suponer un mal funcionamiento. AT ENCIÓN : Cualquier cambio o modificación que se realice sin ser aprobado expresamente por la parte responsable de la conformidad, es susceptible de anular el derecho del usuario a utilizar este equipo. NOTA : Se ha comprobado que este equipo cumple con las especificaciones de un dispositivo digital de clase B, de acuerdo con la sección 15 de la norma FCC. Estas especificaciones se han diseñado para garantizar una protección adecuada contra las interferencias nocivas en instalaciones domésticas. Este aparato genera, utiliza y puede emitir energía en radiofrecuencia y, si no se instala y utiliza según las instrucciones, puede causar interferencias en la radiocomunicación. Sin embargo, no hay garantía de que no se produzcan interferencias en instalaciones concretas. Si este equipo causa interferencias nocivas en la recepción de radio o televisión, lo que puedes comprobar encendiendo y apagando el aparato, puedes intentar corregir el problema, como sigue: - Reorienta o reubica la antena de recepción. - Aumenta la separación entre el equipo y el receptor. - Conecta el equipo a un circuito que no sea el del receptor. Pide ayuda al vendedor o a un técnico de radio/TV. GUARDA ESTAS IN…

Text truncated - open the document above for the full version.

© Inter IKEA Systems B.V. 2014 June 02 th , 2020 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement IKEA of Sweden AB FCC ID: FHO-T2011 To Whom It May Concern: We, IKEA of Sweden AB, hereby authorized Intertek Semko AB, Swedens to act as our Agent for the purpose of preparing application for FCC ID number FHO- T2011 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is June 02th, 2020. The Limited Agency Agreement expires on October 31st , 2020, unless sooner terminated or extended by written notice to Intertek Semko AB, Sweden and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Ivan Susak Team Manager, Laws&Standards IKEA of Sweden AB [email protected] +4647681000

© Inter IKEA Systems B.V. 2014 Jun 02, 2020 Attention: Application Examiner RE: Request for Confidentiality Applicant: IKEA of Sweden AB FCC ID: FHO-T2011 To Whom It May Concern: Permanent Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: • Schematics • Detailed Block Diagrams • Detailed Operational/Functional Description Short-term Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization: • Test setup photos • External photos • Internal photos • User manual Rationale for request for confidentiality: IKEA of Sweden AB has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential © Inter IKEA Systems B.V. 2014 portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] Sincerely, Ivan Susak Team Manager –Laws & standards IKEA of Sweden AB [email protected] +4647681000

Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 1 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se ANNEX 1 Photos of EUT Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 2 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 3 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Photos of test setup, LED1805E22 Test setup for conducted emission 150 kHz – 30 MHz Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 4 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test set up radiated emission 30 MHz – 1 GHz Test set up radiated emission 1 – 13 GHz

Revision 4 Revision Comment FCC and IC typo correction No. of Changes Checked by Approved by Jörgen Skoog (oogj) Approved date 2020-10-09 Designed by IKEA of Sweden No. of Pages 1 (1) Tolerance Replaces document Description Plafond ♦ ♦ _____________________________________________________________________________________ Name T2011 - Type Label NA Product Name OSVALLA Doc number 2199828 De IKE Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual prop-erty rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 MEASURED IMAGE IKEA of Sweden AB

Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 1 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se ANNEX 1 Photos of EUT Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 2 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 3 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Photos of test setup, LED1805E22 Test setup for conducted emission 150 kHz – 30 MHz Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 4 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test set up radiated emission 30 MHz – 1 GHz Test set up radiated emission 1 – 13 GHz

Test report No. 1907679STO-001, Ed. 2 Page 2 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 Revision History Edition Date Description Changes 1 May 24, 2019 First release 2 February 11, 2020 Second release The report was updated according to order number 2010438STO-101 Photos of EUT and test setups in annex 1. Test report No. 1907679STO-001, Ed. 2 Page 3 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 CONTENTS Page 1. Client Information ............................................................................................................. 4 2. Equipment under test (EUT)............................................................................................. 4 2.1 Identification of the EUT ........................................................................................... 4 2.2 Test set up and EUT photos .................................................................................... 4 2.3 Purpose of the test ................................................................................................... 5 2.4 Additional information about the EUT ...................................................................... 5 2.5 Modifications made to improve EMC-characteristics ............................................... 5 3. Test Specifications ........................................................................................................... 6 3.1 Standards ................................................................................................................. 6 3.2 Additions, deviations and exclusions from standards and accreditation ................. 6 3.3 Test site .................................................................................................................... 6 3.4 Mode of operation during the test ............................................................................ 6 3.5 Compliance .............................................................................................................. 7 4. Test Summary .................................................................................................................. 8 5. Conducted continuous disturbances ................................................................................ 9 5.1 Operating environment ............................................................................................. 9 5.2 Test set-up and test procedure ................................................................................ 9 5.3 Measurement uncertainty ......................................................................................... 9 5.4 Test results, AC Power input port, Class B, max luminous intensity ..................... 10 5.5 Test results, AC Power input port, Class B, min luminous intensity ...................... 11 5.6 Test equipment ...................................................................................................... 12 6. Radiated rf Emission in the frequency-range 30 MHz – 13 GHz ................................... 13 6.1 Operating environment ........................................................................................... 13 6.2 Test set-up and test procedure .............................................................................. 13 6.3 Test conditions ....................................................................................................... 13 6.4 Measurement uncertainty ....................................................................................... 14 6.5 Test results, 30 – 1000 MHz, Class B, max luminous intensity ............................. 15 6.6 Test results, 30 – 1000 MHz, Class B, min luminous intensity .............................. 16 6.7 Test equipment ...................................................................................................... 17 6.8 Test results, 1 – 13 GHz, Class B, max luminous intensity ................................... 18 6.9 Test results, 1 – 13 GHz, Class B, min luminous intensity .................................... 19 6.10 Test equipment ...................................................................................................... 19 Test report No. 1907679STO-001, Ed. 2 Page 4 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 1. CLIENT INFORMATION The EUT has been tested by request of Company IKEA of Sweden AB Box 702 343 81 Älmhult Sweden Name of contact Jörgen Skoog 2. EQUIPMENT UNDER TEST (EUT) 2.1 Identification of the EUT Equipment Self-ballasted LED-lamp Type/Model LED1805E22 Brand name Serial Number - Manufacturer IKEA of Sweden AB Rating 120 V, 60 Hz, max 25 W Class - Highest frequency 2405 – 2480 MHz Software version - Rating plate 2.2 Test set up and EUT photos Test set up and EUT photos are enclosed in Annex 1 to this test report. Test report No. 1907679STO-001, Ed. 2 Page 5 (19) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 2.3 Purpose of the test The purpose of the tests was to verify that the EUT fulfills the requirements according to FCC 47 CFR Part 15: Radio frequency device, Subpart B: Unintentional radiators Class B and ICES- 005 Issue 5: Lighting Equipment, Class B. 2.4 Additional information about the EUT The EUT is a self-ballasted LED – lamp provided with a radio remote control for on/off, color setting and dimming. The EUT has the following noted components: radio module, type ICC-A-1 The EUT was tested in a tabletop configuration. The EUT was tested with the following cables Port Type Length [m] Specifications AC Mains Fixed connection - - 2.5 Modifications made to improve EMC-characteristics In order to comply with the requirements regarding radiated emission 30 – 1000 MHz, the electronic is slightly modified by the manufacturer. The modification of the electronic circuit consists of ad…

Text truncated - open the document above for the full version.

Test report No. 1914673STO-001, Ed. 4 Page 2 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 Revision History Edition Date Description Changes 1 December 4, 2019 First release 2 February 11, 2020 Second release New version of rating plate 3 July 06, 2020 Third release The report was updated according to order no. 2022121 Addition of test setup photos in annex 1 4 September 02, 2020 Fourth release The report was updated according to order no. 2022121 Editorial change in test report Test report No. 1914673STO-001, Ed. 4 Page 3 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 Reference type/model Test report no.: 1907679STO-001, Ed.2 Standards: FCC 47 CFR Part 15: Radio frequency device, Subpart B: Unintentional radiators. ICES-005 Issue 4: 2015: Lighting Equipment, Class B Equipment: Self-ballasted LED-lamp Type / model : LED1805E22 Brand name: IKEA Manufacturer : IKEA of Sweden AB Rating: 120 V AC, 60 Hz, max 25 W Opinions and interpretations This test report covers an alternative type/model, presumed to have the same emission- characteristics as the above mention tested reference type/model. According to the manufacturer, the alternative type/model is identical to the tested type/model except for the following differences: The luminaire T2011 Osvalla comprises of the LED module, type LED1805E22 and a lampshade, the only electric/electronic part is the separately emission tested module LED1805E22. Adding the lampshade is considered not to imply different emission-characteristics when compared to the tested LED module LED1805E22. Therefore, T2011 Osvalla is not tested, but considered to have the same emission-characteristics as the tested LED module LED1805E22. Rating plate T2011 Osvalla Test report No. 1914673STO-001, Ed. 4 Page 4 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Version 2.00 EUT photos are enclosed in Annex 1 to this report. Updated standards The update/change of standard ICES-005 Issue 4 to ICES-005 Issue 5 does not affect the measurements performed. The luminaire T2011 Osvalla is therefore deemed to fulfil ICES-005 Issue 5.

Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 1 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se ANNEX 1 Photos of EUT Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 2 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 3 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Photos of test setup, LED1805E22 Test setup for conducted emission 150 kHz – 30 MHz Test report no. 1914673STO-001 Annex 1, Ed. 4 Page 4 (4) Intertek Semko AB Torshamnsgatan 43, Box 1103, SE-164 22 Kista, Sweden www.intertek.se Test set up radiated emission 30 MHz – 1 GHz Test set up radiated emission 1 – 13 GHz