FHO-V1710Wall-mounted luminaire

1 SVALLIS 2AA-2164600-2 English INSTALLATION INSTRUCTIONS CAUTION: Before starting, turn off power at main circuit panel. English Different materials require different types of fittings. Always choose screws and plugs that are specially suited to the material. English WARNING Deviation from the assembly instructions may result in a risk of fire or electric shock. English This device complies with part 15 of the FCC Rules. Operation is subjected to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the quipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAVE THESE INSTRUCTIONS 3 Français INSTRUCTIONS D'INSTALLATION ATTENTION: coupez l'alimentation avant de procéder à l'installation. Français Le choix des vis dépend du matériau dans lequel elles doivent être fixées. Utiliser des vis et chevilles adaptées au matériau du support. Français ATTENTION Tout écart par rapport aux instructions d'assemblage peut entraîner un risque d'incendie ou de choc électrique. Français Cet appareil est conforme à la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer de brouillage préjudiciable et 2. il doit accepter tout brouillage reçu, y compris le brouillage pouvant entraîner un mauvais fonctionnement. ATTENTION: Tout changement apporté à cet appareil non expressément approuvé par la partie responsable de la conformité est susceptible d’annuler le droit de l’utilisateur à se servir de cet équipement. Note: Cet équipement a été testé et déclaré conforme aux limites imposées aux appareils numériques de la classe B, en vertu de la partie 15 des règles de la FCC. Ces limites sont conçues pour assurer une protection suffisante contre les interférences nuisibles dans les installations résidentielles. Cet équipement génère, utilise et peut dégager de l’énergie de radiofréqu- ence et, s’il n’est pas installé et utilisé conformément aux instructions du fabricant, provoquer un brouillage préjudiciable aux communications radio. Il n’existe toutefois aucune garantie qu’un équipement particulier ne sera pas victime de brouillage. Si cet équipement entraîne un brouillage préjudiciable à la réception des émis- sions radio ou de télévision, identifi- able en mettant le terminal hors puis sous tension, il est recommandé à l’utilisateur de tenter de résoudre ce problème au moyen d’une ou plusieurs des mesures suivantes: - Orienter l’antenne réceptrice différemment ou la changer de place. - Augmenter la distance séparant l’équipement du récepteur. - Connecter l’appareil à une prise sur un circuit différent de celui auquel est branché le récepteur. - Obtenir de l’aide auprès du revendeur ou d’un technicien radio/TV expérimenté. CONSERVER CES MESURES DE SÉCURITÉ 4AA-2164600-2 Español INSTRUCCIONES DE MONTAJE ADVERTENCIA: Antes de comenzar el montaje, cortar la luz en el cuadro general. Español Diferentes materiales requieren diferentes clases de herrajes. Recuerda que los tornillos y tacos que elijas se deben adaptar al material en el que irán sujetos. Español ADVERTENCIA No seguir las instrucciones de montaje puede resultar en incendio o descarga eléctrica. Español Este aparato cumple la parte 15 de las normas FCC. Su funcionamiento está sujeto a las dos condiciones siguientes: 1. Este aparato no debe provocar interferencias perjudiciales. 2. Debe aceptar cualquier interferencia que reciba, incluidas las interferencias que puedan suponer un mal funcionamiento. ATENCIÓN: Cualquier cambio o modificación que se realice sin ser aprobado expresamente por la parte responsable de la conformidad, es susceptible de anular el derecho del usuario a utilizar este equipo. Nota: se ha comprobado que este equipo cumple con las especificaciones de un dispositivo digital de clase B, de acuerdo con la sección 15 de la norma FCC. Estas especificaciones se han diseñado para garantizar una protección adecuada contra las interferencias nocivas en instalaciones domésticas. Este aparato genera, utiliza y puede emitir energía en radiofrecuencia y, si no se instala y utiliza según las instrucciones, puede causar interferencias en la radiocomunicación. Sin embargo, no hay garantía de que no se produzcan interferencias en instalaciones concretas. Si este equipo causa interferencias nocivas en la recepción de radio o televisión, lo que puedes comprobar encendiendo y apagando el aparato, puedes intentar corregir el problema, como sigue: -Reorienta o reubica la antena de recepción. -Aumenta la separación entre el equipo y el receptor. -Conecta el equipo a un circuito que no sea el del receptor. -Pide ayuda al vendedor o a un técnico de radio/TV. GUARDA ESTAS INSTRUCCIONES 5 6AA-2164600-…

Text truncated - open the document above for the full version.

© Inter IKEA Systems B.V. 2014 Nov 02, 2020 Federal Communications Commission 44 5 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement IKEA of Sweden AB FCC ID: FHO-V1710 To Whom It May Concern: We, IKEA of Sweden AB, hereby authorized Intertek Semko AB, Sweden to act as our Agent for the purpose of preparing application for FCC ID number FHO- V1710 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is Nov 02 2020. The Limited Agency Agreement expires on May 02 , 2021, unless sooner terminated or extended by written notice to Intertek Semko AB, Sweden and the Federal Communications Commission. This i s to advise that we are in fu ll compliance with the Anti-Drug Abuse Act. The applicant i s not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Ivan Susak Team Manager, Laws&Standards IKEA of Sweden AB [email protected] +4647681000

© Inter IKEA Systems B.V. 2014 November 01, 2020 Attention: Application Examiner RE: Request for Confidentiality Applicant: IKEA of Sweden AB FCC ID: FHO-V1710 To Whom It May Concern: Permanent Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: •Schematics •Detailed Operational/Functional Description •Block diagram •Parts list Short-term Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization: •Test setup photos •External photos •Internal photos •User manual Rationale for request for confidentiality: IKEA of Sweden AB has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential © Inter IKEA Systems B.V. 2014 portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] Sincerely, Ivan Susak Team Manager –Laws & standards IKEA of Sweden AB [email protected] +4647681000

External Photos Photo 1 - External view Photo 2 - External view

Revision 1 Revision Comment No. of Changes Checked by Approved by Elias Molin (elmol8) Approved date 2019-05-27 Designed by Eva Lilja Löwenhielm No. of Pages 1 (1) Tolerance Replaces document Description Wall lamp ♦ ♦ _____________________________________________________________________________________ Name V1710 - Placement of labels Product Name SVALLIS Doc number 2182971 Measurements according to the SI systems. This drawing is IKEA` property and is covered by industrial and intellectual prop- erty rights and should, without written consent from IKEA, in no way be copied, reproduced or communicated or otherwise used for any other purpose other than that which has been agreed. A4 Template Version: 3.0 MEASURED IMAGE IKEA of Sweden AB Label size:82x42mm

   
     !"# $$$$!  %&' !()*+ )' !()*
,--., !,/ 012134-,.5 .-( *,- -1,1-6($*, -1--- -6-15-, -11 1 /%7/82' 9999999

Internal Photos Photo 1 - Internal view Photo 2 - Internal view Photo 3 - Internal view Photo 4 - Internal view

IKEA of Sweden AB TEST REPORT SCOPE OF WORK: FCC Part 15 subpart B – EMC report Model: V1710 Svallis REPORT NUMBER 170701491SHA-001 ISSUE DATE April 4, 2019 DOCUMENT CONTROL NUMBER TTRFFCCPART15b_V1 © 2018 Intertek Intertek Testing Services Shanghai, Building No.86, 1198 Qinzhou Road (North), Caohejing Development Zone, Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCPART15b_V1 © 2018 Intertek Page 2 of 20 Report no. 170701491SHA-001 Applicant : IKEA of Sweden AB P.O. Box 702, SE-343 81 Älmhult, SWEDEN Manufacturer : Same as applicant Manufacturing site : Zhejiang Hao Ting Lighting Co., Ltd. Feng Ming Industrial Zone, Tongxiang City, Zhejiang Province, 314505, CHINA Summary The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2017): Radio Frequency Devices (Subpart B) ANSI C63.4 (2014): American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz PREPARED BY: REVIEWED BY: Star Guo Andy Chen Project Engineer Reviewer Report No. 170701491SHA-001 TTRFFCCPART15b_V1© 2018 Intertek Page 3 of 20 Contents REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 6 1.2 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST ................................................................................................................... 8 2.3 TEST SOFTWARE LIST ............................................................................................................................................ 8 2.4 TEST PERIPHERALS LIST ......................................................................................................................................... 8 2.5 RECORD OF CLIMATIC CONDITIONS .......................................................................................................................... 8 2.6 INSTRUMENT LIST ................................................................................................................................................ 9 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 10 3 CONDUCTED EMISSION ............................................................................................................................. 11 3.1 LIMITS ............................................................................................................................................................. 11 3.1.1 Limits for conducted emission of class A device .................................................................................. 11 3.1.2 Limits for conducted emission of class B device .................................................................................. 11 3.2 TEST SETUP ...................................................................................................................................................... 12 3.3 TEST SETUP AND TEST PROCEDURE ....................................................................................................................... 13 3.4 TEST PROTOCOL ................................................................................................................................................ 14 4 RADIATED EMISSION ................................................................................................................................. 16 4.1 RADIATED EMISSION LIMITS ................................................................................................................................. 16 4.1.1 Limits for radiated emission of class A device ..................................................................................... 16 4.1.2 Limits for radiated emission of class B device ..................................................................................... 16 4.2 BLOCK DIAGRAM AND TEST SET UP ..................................................................................................…

Text truncated - open the document above for the full version.

Test Setup Photos 1. Radiated Emission 2. Conducted Emission