FSUGMZHEWireless Mouse

Hardware Installation 1.You can connect the receiver to a USB port of a PC 2.Install one AA battery in the mouse. 3.Turn on your computer. 4.After you open Windows, please press the button on the receiver first and then press the button under the mouse for channel setting. Important: Remember do not put the batteries in the wrong direction, use the same types of batteries. Also, keep all drinks away! If any spill occurs on the receiver, unplug the USB connector first and clean the receiver immediately. Please switch the button to "off" under the mouse once you don't use it for a long time, and remove the batteries if you do not use this device for at least two weeks. Warning: (Troubleshooting) 1.Please do not use Wireless optical mouse on a desk which is made of glass, mir - ror, iron, or black velvet. Also, a flat surface is necessary or the Optical Sensor will error easily. When you use Wireless optical mouse on a desk that is made of metal, try using a pad and reduce the receiving distance. 1 ENGLISH 2.Before the first installation is completed (channel setting ready), the mouse will not work in DOS. 3.The Wireless optical mouse channel provides 256 ID-codes, and it automatically selects the ID # for your mouse. You can only set up one Wireless optical mouse at a time. But if you have additional Wireless optical mouse sets in an area of 10 square meters, more interference will occur between the receiver and your mouse. 4.If you feel the mouse does not move smooth as usual, then the batteries have lost their charge, so please replace them. 5.The Wireless optical mouse with radio frequency gives you free movement and an enjoyable experience. For optimal performance, place the receiver at least 8 inches (about 20 cm) away from the mouse and other electrical devices, such as the computer, monitor, and etc. Software Installation 1. Make sure the mouse is connected to the computer. 2. Put the Setup disk (or CD) into the disk drive. 3. Follow the instructions on the screen to finish the software installation. Factory Setting 2 Button Assignments The Button Assignment feature lets you work in a more efficient way because you can assign the most fre - quently used commands in Windows to the mouse but - tons. Magic-RollerPress the “Magic-Roller” to surf the Internet and Windows documents Horizontal Scroll Press the roller to the left and the cursor scrolls to the left; press the roller to the right and the cursor scrolls to the right. Left ButtonProvides traditional mouse functions such as click, double click and drag. Right ButtonYou can assign this button frequently used keyboard and mouse func - tions in addition to features like EasyJump, Auto-Panning, Zoom, etc. Roller ButtonYou can assign this button frequently used keyboard and mouse func- tions in addition to features like EasyJump, Auto-Panning, Zoom, etc. 3 FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

SPORTON International Inc. PAGE NUMBER : A1 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255

Label Location

SPORTON International Inc. PAGE NUMBER : A1 OF A3 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A3 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A3 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 27, 2005 FAX : 886-2-2696-2255

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: RF-15.227-a FCC RADIO TEST REPORT Applicant’s company KYE SYSTEMS CORP Applicant Address NO.492, Sec. 5, Chung Hsin Rd., San Chung, Taipei Hsien, 241, Taiwan, R.O.C. FCC ID FSUGMZHE Manufacturer’s company KYE SYSTEMS CORP Manufacturer Address NO.492, Sec. 5, Chung Hsin Rd., San Chung, Taipei Hsien, 241, Taiwan, R.O.C. Product Name Mouse Model Name Please refer to section 3.7 Test Rule Part(s) 47 CFR FCC Part 15 Subpart C § 15.227 Test Freq. Range 26.96 ~ 27.28 MHz Receive Date Dec. 20, 2005 Test Date Dec. 23, 2005 Submission Type Original Equipment Statement The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report No.: FR5D1914 Report Format Version: RF-15.227-a Page No. : i of ii FCC ID: FSUGMZHE Issued Date : Dec. 28, 2005 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................3 3.3. Table for Filed Antenna.......................................................................................................................................................................3 3.4. Table for Carrier Frequencies .............................................................................................................................................................3 3.5. Table for Test Modes ...........................................................................................................................................................................4 3.6. Table for Testing Locations..................................................................................................................................................................4 3.7. Table for Multiple Listing......................................................................................................................................................................4 3.8. Table for Supporting Units ...................................................................................................................................................................4 3.9. Test Configurations .............................................................................................................................................................................5 4. TEST RESULT ..................................................................................................................................................... 7 4.1. AC Power Line Conducted Emissions Measurement...........................................................................................................................7 4.2. Field Strength of Fundamental Emissions Measurement ...................................................................................................................11 4.3. 20dB Spectrum Bandwidth Measurement ........................................................................................................................................13 4.4. Radiated Emissions Measurement ....................................................................................................................................................15 4.5. Band Edge Emissions Measurement .................................................................................................................................................22 4.6. Antenna Requirements .....................................................................................................................................................................24 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 25 6. SPORTON COMPANY PROFILE ........................................................................................................................ 27 6.1. Test Location.....................................................................................................................................................................................27 7. CERTIFICATE OF NVLAP ACCREDITATION ......................................................................................................... 28 APPENDIX A. PHOTOGRAPHS OF EUT.........................................................................................................A1 ~ A15 APPENDIX B. TEST PHOTOS.......................................................................................................................... B1 ~ B3 Report No.: FR5D1914 Report Format Version: RF-15.227-a Page No. : ii of ii FCC ID: FSUGMZHE Issued Date : Dec. 28, 2005 History of This Test Report Original Issue…

Text truncated - open the document above for the full version.

Report No.: FR5D1914 FCC ID: FSUGMZHE Page No. : 1 of 3 Appendix B. Test Photos Report No.: FR5D1914 FCC ID: FSUGMZHE Page No. : 2 of 3 1. Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR5D1914 FCC ID: FSUGMZHE Page No. : 3 of 3 2. Photographs of Radiated Emissions Test Configuration FRONT VIEW REAR VIEW