FSUGMZIZMICRO TRAVELER 900S

English 1 Hardware Installation Note: Supports Windows 7/Vista/XP 1. You can connect the receiver to a USB port of a PC. 2. Install one AAA battery in the mouse. 3. Make sure that you have switched on the power switch underneath the mouse. 4. Stick-N-Go: attach the ‘Click Mount’ on your notebook in a convenient position first, then you can attach the mouse on your notebook as shown to avoid dropping your mouse. Warning: (Troubleshooting) 1. Do not use the wireless optical/laser mouse on a desk which is made of glass or mirror. 2. The connection of the wireless device is factory preset, so when you plug the USB receiver into any USB port, the connection between the micro receiver and the mouse will be established automatically. 3. In case your PC did not install the hardware successfully, remove the micro receiver from the USB port and go Human Interface Devices under Device Manager to remove the mouse then plug in the micro receiver to a USB port again. 4. If you feel the mouse does not move smooth as usual, it is possible the batteries have lost their charge so you need to replace them. Remember to put the batteries in the correct direction. Factory Settings 1. Left Button: Provides traditional mouse functions like click, double click and drag. 2. Magic-Roller: Press the “Magic-Roller” to surf the Internet and Windows documents. 3. Right Button: Provides traditional mouse click functions. Federal Communications Commission (FCC) Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installations, if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient / Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that the receiver is connected. 4. Consult the dealer or an experienced radio / TV technician for help. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. Disclaimer The following does not apply to any country where such provisions are inconsistent with local law: KYE Systems Corp. makes no warranties with respect to this documentation, whether expressed or implied. All material is provided “as is”. This includes, but is not limited to, any implied warranties of merchantability and fitness is for a particular purpose. The information covered in this document is subject to change without notice. KYE Systems Corp. assumes no responsibility for any errors that may appear in this document. All brand names mentioned in this manual are trademarks or registered trademarks of their respective companies. Copyright © 2009 KYE Systems Corp. All rights reserved.

Confidentiality Requiring Letter Applicant Name: KYE Systems Corp. Address: No.492,Sec.5, Chung Hsin Rd., San Chung, Taipei Hsien, Taiwan R.O.C. Date: January/ 07/ 2010 To: Federal Communications Commission Authorization and Evaluation Division FCCID: FSUGMZIZ Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Applicant as outlined below: 1. Schematics............................................. (Circiut_d_GM-090021-T) 2. Block Diagram......................................... (Block_d_GM-090021-T) 3. Operational Description.............................. (Operation_d_GM-090021-T) The above materials contain trade secrets and proprietary information not customarily Released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understood that pursuant to rule 0.457, disclosure of this Applicant and all accompanying documentation will not be made before the date of ths Grant for this application. Sincerely, Ming Huang Lee(Typed) ___________________________________________________

Global Certification Corp. PHOTO OF EUT PHOTOS OF EUT Global Certification Corp. Report No. : F9N0501 PHOTO OF EUT PHOTO OF EUT : 1 of 3 Front View of EUT 1 Rear View of EUT 1

Label location

Global Certification Corp. Report No. : F9N0501 PHOTO OF EUT PHOTO OF EUT : 2 of 3 Inside View of EUT 1 Inside View of EUT 1-1 Global Certification Corp. Report No. : F9N0501 PHOTO OF EUT PHOTO OF EUT : 3 of 3 Component Side of Main Board 1 Solder Side of Main Board 1

RF產品之技術規格表 1. 產品名稱 Micro Traveler 900S (GM-090021/T) 型號： 2. 電源輸入額定值： ■DC 1.5 V, A; □ AC V, A 3. Frequency Band： 2.4GHz ~ 2.5GHz Carrier Frequency： 2.4GHz 4. Number of Channel： 78 5. Channel Spacing： 6. RF Output Power (ERP or EIRP) ： -1dBm 7. I.F.： MHz; L.O.： MHz 8. Modulation Type： GFSK 9. Duty Cycle： % 10. Mode of operation (duplex, simplex) ： duplex 11. Bit Rate of Transmission： 12. Antenna Type： PCB Antenna 13. Antenna gain： -3 dBi 14. Operating Temperature Range： °C 15. Channel bandwidth ： 1MHz 16. 預定銷售國家：

Global Certification Corp. Date of Issue: Dec 24,2009 Report No:F9N0501 Page1/25 FCC 47 CFR PART 15 SUBPART C TEST REPORT FOR Product Name: Micro Traveler 900S Model : GM-090021/T Trade Name: Genius Issued to KYE SYSTEMS CORP. No.492,Sec.5, Chung Hsin Rd., San Chung, Taipei Hsien, 24160, Taiwan, R.O.C. Issued by Global Certification Corp. EMI Test Site Sansia Lab NO.34-3,Zihhe Rd.,Sansia Township,Taipei County 237, Taiwan ,R.O.C. EMC Test Site Sijhih office and Lab No. 146. Sec.2. Siangjhang Rd. Sijhih City. Taipei County 221, Taiwan(R.O.C.) Note: This test refers exclusively to the test presented test model and sample. This report shall not be reproduced except in full, without the written approval of Global Certification Corporation. This document may be altered or revised by Global Certification Corporation. Personnel only, and shall be noted in the revision section of the document. Global Certification Corp. Date of Issue: Dec 24,2009 Report No:F9N0501 Page2/25 TABLE OF CONTENTS ----------------------------------------------------------------------------------------------------- 2 1. GENERAL INFORMATION -------------------------------------------------------------------------------------------------------- 3 1.1 DESCRIPTION OF THE TESTED SAMPLES-----------------------------------------------------------------------------------------------4 2. TEST METHODOLOGY ------------------------------------------------------------------------------------------------------------- 5 2.1 GENERAL TEST PROCEDURES --------------------------------------------------------------------------------------------------- 5 2.2 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ----------------------------------------------------------------- 5 2.3 DESCRIPTION OF TEST MODES -------------------------------------------------------------------------------------------------- 6 2.4 DESCRIPTION OF THE SUPPORT EQUIPMENTS ----------------------------------------------------------------------------- 7 3. TEST AND MEASUREMENT EQUIPMENT ----------------------------------------------------------------------------------- 9 3.1 CALIBRATION-----------------------------------------------------------------------------------------------------------------------9 3.2 EQUIPMENT--------------------------------------------------------------------------------------------------------------------------9 4. SECTION 15.249 REQUIREMENTS (FUNDAMENTAL/ HARMONICS) ----------------------------------------------11 4.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------11 4.2 LIMIT-------------------------------------------------------------------------------------------------------------------------------11 4.3 RESULT: PASSED --------------------------------------------------------------------------------------------------------------11 4.4 TEST DATA:------------------------------------------------------------------------------------------------------------------------11 5. SECTION 15.205 REQUIREMENTS (BAND EDGE)-------------------------------------------------------------------------15 5.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------15 5.2 LIMIT-------------------------------------------------------------------------------------------------------------------------------15 5.3 RESULT: PASSED --------------------------------------------------------------------------------------------------------------16 5.4 TEST DATA:------------------------------------------------------------------------------------------------------------------------16 6. SECTION 15.209 REQUIREMENTS (GENERAL RADIATED EMISSION) -------------------------------------------20 6.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------20 6.2 LIMIT-------------------------------------------------------------------------------------------------------------------------------21 6.3 TEST PROCEDURE-----------------------------------------------------------------------------------------------------------------22 6.4 RESULT: PASSED ----------------------------------------------------------------------------------------------------------------22 6.5 TEST DATA:------------------------------------------------------------------------------------------------------------------------23 7. SECTION 15.207 REQUIREMENTS (POWERLINE CONDUCTED EMISSIONS) ----------------------------------25 APPENDIX 1 PHOTOS OF TEST CONFIGURATION APPENDIX 3 PHOTOS OF EUT Global Certification Corp. Date of Issue: Dec 24,2009 Report No:F9N0501 Page3/25 1. GENERAL INFORMATION Applicant :KYE SYSTEMS CORP. Address :No.492,Sec.5, Chung Hsin Rd., San Chung, Taipei Hsien, 24160, Taiwan, R.O.C. Manufacturer :KYE SYSTEMS CORP. Address :No.492,Sec.5, Chung Hsin Rd., San Chung, Taipei Hsien, 24160, Taiwan, R.O.C. EUT : Micro Traveler 900S Model Name :GM-090021/T Model Differences :N/A Is here with confirmed to comply with the requirements set out in the FCC Rules and Regulations Part 15 Subpart C and the measurement procedures were according to ANSI C63.4-2003. The said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment are within the compliance requirements. FCC part 15 subpart C Receipt Date : 11/05/2009 Final Test Date : 12/16/2009 Taipei, Taiwan Dec.24 , 2009 Alex Chou / Manager (Place) (Date) (Signature) Designation Number: TW1030 Global Certification Corp. Date of Issue: Dec 24,2009 Report No:F9N0501 Page4/25 1.1 DESCRIPTION OF THE TESTED SAMPLES EUT Name : Micro Traveler 900S Model Number : GM-090021/T FCC ID : FSUGMZIZ Input Voltage : 1.5Vdc Power From Inside Outside Adaptor BATTERY AC Power Source DC Power Source Support Unit PC Operate Frequency : Refer to the channel list as described below Modulation Technique : GFSK N…

Text truncated - open the document above for the full version.

Global Certification Corp. Appendix 1 PHOTOS OF TEST CONFIGURATION Global Certification Corp. Report No. : F9N0501 Appendix 1 : 1 of 1