G2R-6160ALeapLand Adventures

Instruction Manual This guide contains important information. Please keep it for future reference. IM-616000-000 US 2 INTRODUCTION Thank you for purchasing the PAW Patrol: To the Rescue! learning video game! Go on missions with the PAW Patrol to save Adventure Bay and learn problem-solving skills along the way! INCLUDED IN THE PACKAGE • 1 wireless controller • 1 HDMI game stick • 1 micro USB power cable • Quick Start Guide WARNING All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties and packaging screws are not part of this toy and should be discarded for your child’s safety. NOTE Please save this Instruction Manual as it contains important information. D-Pad B Button A Button Home Button Help Button HDMI Game Stick Wireless Controller Power Switch Micro USB Power Cable 3 ATTENTION Pour la sécurité de votre enfant, débarrassez-vous de tous les produits d’emballage tels que rubans adhésifs, feuilles de plastique, attaches, étiquettes et vis d’emballage. Ils ne font pas partie du jouet. NOTE Il est conseillé de conserver ce guide des parents car il comporte des informations importantes. GETTING STARTED INITIAL SETUP 1. Plug the USB B Connector end of the Micro USB Power Cable into the USB B port on the HDMI Game Stick. 2. Plug the HDMI Game Stick into an HDMI port on your television. 3. Plug the USB A Connector end of the Micro USB Power Cable into a USB port on your television or other qualified DC 5V adapter with output no less than 500mA. 4. Make sure your television is set to display the same HDMI port that the HDMI Game Stick is plugged into. 5. Find the battery cover located on the back of the Wireless Controller, use a screwdriver to loosen the screw and then open the battery cover.* 6. Remove old batteries by pulling up on one end of each battery. 7. Install 2 new AA (AM-3/LR6) batteries following the diagram inside the battery box. (For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended.) 8. Replace the battery cover and tighten the screw to secure. 9. Turn the power switch on the device to On. 4 * To ensure proper connectivity, install batteries in the device after the HDMI Game Stick has been plugged into the television. NOTE The HDMI Game Stick is only compatible with television sets and is not compatible with computers or computer monitors. WARNING: Adult assembly required for battery installation. Keep batteries out of reach of children. ATTENTION : Les piles ou accumulateurs doivent être installés par un adulte. Tenir les piles ou accumulateurs hors de portée des enfants. IMPORTANT: BATTERY INFORMATION • Insert batteries with the correct polarity (+ and -). • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries. • Only batteries of the same or equivalent type as recommended are to be used. • Do not short-circuit the supply terminals. • To save battery, turn off the controller when finish using it. • Remove batteries during long periods of non-use. • Remove exhausted batteries from the toy. • Dispose of batteries safely. Do not dispose of batteries in fire. • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas • A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. RECHARGEABLE BATTERIES • Remove rechargeable batteries (if removable) from the toy before charging. • Rechargeable batteries are only to be charged under adult supervision. • Do not charge non-rechargeable batteries. 5 NOTE If the Wireless Controller powers down or if the light fades out during play, please install a new set of batteries. PRODUCT FEATURES 1. D-Pad • Press the D-Pad on the Wireless Controller to select an item on the Menu screen. • See Games section below for D-Pad usage in individual games. 2. Home Button • Press the Home Button on the Wireless Controller to quit a level, quit the game, or return to the previous Menu screen. 3. Help Button • Press the Help Button on the Wireless Controller to hear hints and tips on how to play the game or navigate the Menu screen. 4. A Button • Press the A Button on the Wireless Controller to select the highlighted objects on the Menu screen. • See Games section below for A Button usage in individual games. 5. B Button • Press the B Button on the Wireless Controller to return to the previous Menu screen. • See Games section below for B Button usage in individual games. 6. Menu Screens • The following Menu screens appear in the game. Profile Selection Screen • Create or delete a saved profile on the Save Selection screen. • If a saved file has been accidentally deleted, highlight a New save slot and press the following buttons on the Wireless Controller: Home + Home + Help + Help + B + B + Help + Home + B. This will recover the deleted file. Note: Pressing the above buttons will also unlock all missions in the game. 6 Game Mode Screen • Play missions sequentially by selecting Missions, or individual curricular games in Quick Challenge mode. • Select Grownups option to read about the learning curriculum featured in the product. Mission Menu Screen • Access the different missions from the Mission menu screen. • The player will need to get one star in each game in a mission before the next mission is unlocked. Game Menu Screen • Select a pup’s game within a specific mission. • Stars earned during gameplay will display below each game’s icon. Quick Challenge Menu • Access the games featuring learning curriculum by selecting one of the three icons on screen associated with each curricular game. 7. Games Chase • Press the D-Pad left and right to move the character. • Press the A Button to make the character jump. • Press the A Button a …

Text truncated - open the document above for the full version.

Standard Form Sample Request for Confidentiality Letter MS-0044715 Page 1 of 1 Revision 0 Date: ___2022-03-03_____ Subject: Confidentiality Request for FCC ID: G2R-6160A and IC: 1135D-6160A ______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term Permanent Internal Photos *** Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Permanent User’s Manual*** Short Term n/a Test Setup Short Term n/a External Photos VTech Electronics Limited has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. (*** PAG only) Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___( 180) ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By: Antony Wong / Senior Manager (Signature/Title) (Print name)

Difference Declaration Original Model No.:6160A, 6160, 80-6160xx Adding Model No.:6132A, 6132, 80-6132xx (xx=00~99, definition of country&language version) To whom it may concern, We, VTech Electronics Limited would like to declare those models 6160A, 6160, 80-6160xx, 6132A, 6132, 80-6132xx are identical in electrical circuit design and PCB layout.The only difference is model number for different market purpose. Sincerely yours, Applicant:VTech Electronics Limited Address: 23F Tai Ping Industrial Center, Block 1, 57 Ting Kok Road,Tai Po,Hong Kong Signature: Name and title:Antony Wong / Senior Manger Email:[email protected] Tel.:+ 26801233

Model: 6160A, 6160, 80-6160xx Model: 6132A, 6132, 80-6132xx

Model: 6160AFCC ID: G2R-6160AIC: 1135D-6160A TM & © 2022 LeapFrog Enterprises, Inc. 6160 Engraving info Battery Door Small size of HDMI TM & © 2022 LeapFrog Enterprises, Inc. leapfrog.com Back of Battery Door Model:6160 FCC ID: G2R-6160 IC: 1135D-6160 CAN ICES-003(B)/NMB-003(B) T H I S D E V I C E C O M P L I E S W I T H P A R T 1 5 O F T H E F C C R U L E S . O P E R A T I O N I S S U B J E C T T O T H E F O L L O W I N G T W O C O N D I T I O N S : ( 1 ) T H I S D E V I C E M A Y N O T C A U S E H A R M F U L I N T E R F E R E N C E , A N D ( 2 ) T H I S D E V I C E M U S T A C C E P T A N Y I N T E R F E R E N C E R E C E I V E D , I N C L U D I N G I N T E R F E R E N C E T H A T M A Y C A U S E U N D E S I R E D O P E R A T I O N .

Antenna 2452MHz

Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: Test Report No. CN22TGV2 001 Seite 19 von 20 Page 19 of 20 6Safety Human Exposure 6.1Radio Frequency Exposure Compliance 6.1.1Electromagnetic Fields RESULT:Pass Test Specification Test standard:FCC KDB Publication 447498 v06 CFR47 FCC Part 2: Section 2.1093 CFR47 FCC Part 1: Section 1.1310 RSS-102 Issue 5 February 2021 FCC requirement: The measured maximum conducted output power of the EUT is 3.89dBm ≈ 2.45mW, which is far below the SAR exclusion threshold level 10mW (SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm), hence the EUT is excluded from SAR evaluation according to FCC KDB publication 447498 D01: Mobile and Portable RF Exposure. Guidance v06. IC requirements: The measured maximum specified e.i.r.p of the EUT is 3.89dBm ≈ 2.45mW, which is far below the SAR exclusion threshold level 4mW, hence the EUT is excluded from SAR evaluation according to RSS-102 Issue 5 section 2.5.1.

Prüfbericht - Produkte Test Report - Products Prüfbericht-Nr.: Test report no.: CN22TGV2 001 Auftrags-Nr.: Order no.: 168357592 Seite 1 von 20 Page 1 of 20 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 2022-02-08 Auftraggeber: Client: VTech Electronics Limited 23F Tai Ping Industrial Center, Block 1, 57 Ting Kok Road,Tai Po,Hong Kong Prüfgegenstand: Test item: PAW PATROL TO THE RESCUE!, PAW PATROL TO THE, PAW PATROL À LA RESCOUSSE !, LeapLand Adventures, L'aventure LeapLand Bezeichnung / Typ-Nr.: Identification / Type no.: 6160A, 6160, 80-6160xx, 6132A, 6132, 80-6132xx (xx=00~99, definition of country&language version) Auftrags-Inhalt: Order content: FCC and IC approval Prüfgrundlage: Test specification: CFR47 FCC Part 15: Subpart C Section 15.247 CFR47 FCC Part 15: Subpart C Section 15.207 CFR47 FCC Part 15: Subpart C Section 15.209 CFR47 FCC Part 2.1091 RSS-247 Issue 2 February 2017 RSS-Gen Issue 5 February 2021 RSS-102 Issue 5 February 2021 Wareneingangsdatum: Date of sample receipt: 2022-02-08 Please refer to photo documents Prüfmuster-Nr.: Test sample no.: A003208195-003 to 004 Prüfzeitraum: Testing period: 2022-02-18 – 2022-03-01 Ort der Prüfung: Place of testing: TÜV Rheinland (Shenzhen) Co., Ltd. Prüflaboratorium: Testing laboratory: TÜV Rheinland (Shenzhen) Co., Ltd. Prüfergebnis*: Test result*: Pass geprüft von: tested by: X Signed by: Alex Lan genehmigt von: authorized by: X Signed by: Winnie Hou Datum: Date: 2022-03-29 Ausstellungsdatum: Issue date: 2022-04-01 Stellung / Position Senior Project Engineer Stellung / Position Department Manager Sonstiges / Other: FCC ID: G2R-6160A IC: 1135D-6160A HVIN: 6160A, 6132A Zustand des Prüfgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged: * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhalt P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specifications(s) F(ail) = failed a.m. test specifications(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be V05 duplicated in extracts. This test report does not entitle to carry any test mark. TÜV Rheinland (Shenzhen) Co., Ltd. 1601 R&D Room, 1602-1604, 17-18F, Building 7 Site C, Vanke Cloud City Phase I, Xingke First Street, Xili Street, Xili Community, Nanshan District, Shenzhen 518052, P.R. China Mail: [email protected] · Web: www.tuv.com Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: Test Report No. CN22TGV2 001 Seite 2 von 20 Page 2 of 20 Test Summary 5.1.1 ANTENNA REQUIREMENT RESULT: Pass 5.1.2 MAXIMUM CONDUCTED OUTPUT POWER RESULT: Pass 5.1.3 CONDUCTED POWER SPECTRAL DENSITY RESULT: Pass 5.1.4 99%DB BANDWIDTH RESULT: Pass 5.1.5 6DB BANDWIDTH RESULT: Pass 5.1.6 CONDUCTED SPURIOUS EMISSIONS MEASURED IN 100 KHZ BANDWIDTH RESULT: Pass 5.1.7 RADIATED SPURIOUS EMISSION RESULT: Pass 6.1.1 ELECTROMAGNETIC FIELDS RESULT: Pass Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: Test Report No. CN22TGV2 001 Seite 3 von 20 Page 3 of 20 Contents 1 GENERAL REMARKS ......................................................................................................................4 1.1 COMPLEMENTARY MATERIALS ........................................................................................................4 2 TEST SITES ...................................................................................................................................4 2.1 TEST FACILITIES ............................................................................................................................4 2.2 LIST OF TEST AND MEASUREMENT INSTRUMENTS .............................................................................5 2.3 TRACEABILITY ...............................................................................................................................6 2.4 CALIBRATION ................................................................................................................................6 2.5 MEASUREMENT UNCERTAINTY ........................................................................................................6 2.6 LOCATION OF ORIGINAL DATA ........................................................................................................6 2.7 STATUS OF FACILITY USED FOR TESTING .........................................................................................6 3 GENERAL PRODUCT INFORMATION ..................................................................................................7 3.1 PRODUCT FUNCTION AND INTENDED USE .........................................................................................7 3.2 RATINGS AND SYSTEM DETAILS ......................................................................................................7 3.3 INDEPENDENT OPERATION MODES ..................................................................................................8 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS ......................................................................8 3.5 SUBMITTED DOCUMENTS ................................................................................................................8 4 TEST SET-UP AND OPERATION MODES ............................................................................................9 4.1 PRINCIPLE OF CONFIGURATION SELECTION ......................................................................................9 4…

Text truncated - open the document above for the full version.

Prüfbericht - Produkte Test Report - Products Appendix A CN22TGV2 001 Page 1 of 2 Appendix A: Photographs of the Test Set-Up APPENDIX A: PHOTOGRAPHS OF THE TEST SET-UP.......................................................................................................1 PHOTOGRAPH 1: SET-UP FOR RADIATED SPURIOUS EMISSION, BELOW 1GHZ....................................................................................2 PHOTOGRAPH 2: SET-UP FOR RADIATED SPURIOUS EMISSION, ABOVE 1GHZ....................................................................................2 Prüfbericht - Produkte Test Report - Products Appendix A CN22TGV2 001 Page 2 of 2 Photograph 1: Set-up for Radiated Spurious Emission, Below 1GHz Photograph 2: Set-up for Radiated Spurious Emission, Above 1GHz