G4O-SP722MID

13 14 FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC RF warning statement: The device has been evaluated to meet general RF exposure requirement.The device can be used in portable expos

SKYTEX TECHNOLOGY INC. Date: February 20, 2013 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: G4O-SP722 To Whom It May Concern: This letter is to ascertain that SKYTEX TECHNOLOGY INC. MID MODEL No.: SP722, SP732, SP766, SP716, SP705, SP723 has been the units used for conducting FCC compliance testing, the DoC part will be tested by FCC recognized test lab. If you have any question or concerns, pls. contact us.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 SKYTEX TECHNOLOGY INC. February 20, 2013 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, SKYTEX TECHNOLOGY INC. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): FCC ID: G4O-SP722 (MID MODEL No.: SP722, SP732, SP766, SP716, SP705, SP723) We affirm that between SIEMIC and SKYTEX TECHNOLOGY INC., any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Cindy Cheung / CFO E-mail: [email protected] Phone: 909-923-8818 Fax: 888-769-5977 Address: 1900 Proforma Ave., #F1 Ontario, CA 91761

Confidentiality Request Letter SKYTEX TECHNOLOGY INC. (2013-01-28) To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Permanent Confidentiality Request for FCC ID: G4O-SP722 We hereby request confidential treatment of information accompanying this application as outlined below: - Block diagram - Operation description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Cindy Cheung / CFO E-mail: [email protected] Phone: 909-923-8818 Fax: 888-769-5977 Address: 1900 Proforma Ave., #F1 Ontario, CA 91761

Family models declaration letter. February 19, 2013 We SKYTEX TECHNOLOGY INC Of 1900 Proforma Ave., #F1 Ontario, CA 91761 address Declare under our sole responsibility that the product Product: MID Model Number SP722, SP732, SP766, SP716, SP705, SP723 All models have the same constructions, circuit diagram and PCB layout. Only model name is different. Unless otherwise stated Thanks Sincerely, Cindy Cheung / CFO E-mail: [email protected] Phone: 909-923-8818 Fax: 888-769-5977 Address: 1900 Proforma Ave., #F1 Ontario, CA 91761

ID Label MID FCC ID: G4O-SP722 Trademark: Model Number: SP722 Made in China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Label Location Proposed Label Location on EUT

WIFI Module Antenna

FCC ID: G4O-SP722 WLAN (Portable device) According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB 447498 (2)(a)(i) Frequency Range Low Frequency (MHz) High Frequency(MHz) Center frequency (MHz) SAR Limitation (mw) 2412 2462 2437 10.mw Maximum measured transmitter power: 802.11b Conducted Power (dBm) Conducted Power (mw) Max Antenna Gain (dBi) EIRP (mw) 9.50 8.91 0 8.91 Maximum measured transmitter power: 802.11g Conducted Power (dBm) Conducted Power (mw) Max Antenna Gain (dBi) EIRP (mw) 8.65 7.32 0 7.32 Maximum measured transmitter power: 802.11n Conducted Power (dBm) Conducted Power (mw) Max Antenna Gain (dBi) EIRP (mw) 7.90 6.17 0 6.17 Threshold at which no SAR required is 10mw. Maximum Tx power is 8.91mw EIRP Conclusion: No SAR is required.

TRF NoFCC 15.247/A Page 1 of 65 Report No ES130109033E ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF MID MODEL No.: SP722, SP732, SP766, SP716, SP705, SP723 Trademark: FCC ID: G4O-SP722 REPORT NO: ES130109033E ISSUE DATE: January 28, 2013 Prepared for SKYTEX TECHNOLOGY INC. 1900 Proforma Ave., #F1 Ontario, CA 91761 Prepared by SHENZHEN EMTEK CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 This report shall not be reproduced, except in full, without the written approval of SHENZHEN EMTEK CO., LTD. TRF NoFCC 15.247/A Page 2 of 65 Report No ES130109033E VERIFICATION OF COMPLIANCE Applicant: SKYTEX TECHNOLOGY INC. 1900 Proforma Ave., #F1 Ontario, CA 91761 Manufacturer: NEXGEN GLOBAL LIMITED FLAT/RM 2001 20/F CHINACHEM JOHNSTON PLAZA 186 JOHNSTON ROAD HK Product Description: MID Model Number: SP722, SP732, SP766, SP716, SP705, SP723 (Note: all the models are the same, except their model number. We take SP722 to test.) Trademark: File Number: ES130109033E Date of Test: January 10, 2013 to January 28, 2013 We hereby certify that: The above equipment was tested by SHENZHEN EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247. The test results of this report relate only to the tested sample identified in this report. Date of Test : January 10, 2013 to January 28, 2013 Prepared by : Sara Tang/Editor Reviewer : Aaron Lai /Supervisor Approve & Authorized Signer : Lisa Wang/Manager TRF NoFCC 15.247/A Page 3 of 65 Report No ES130109033E Ta b l e o f C o n t e n t s 1. GENERAL INFORMATION ................................................................................................................................ 5 1.1 PRODUCT DESCRIPTION.................................................................................................................................... 5 1.2 RELATED SUBMITTAL(S) / GRANT(S)................................................................................................................. 5 1.3 TEST METHODOLOGY....................................................................................................................................... 6 1.4 SPECIAL ACCESSORIES...................................................................................................................................... 6 1.5 EQUIPMENT MODIFICATIONS............................................................................................................................ 6 1.6 TEST FACILITY.................................................................................................................................................. 6 2. SYSTEM TEST CONFIGURATION ................................................................................................................... 7 2.1 EUT CONFIGURATION....................................................................................................................................... 7 2.2 EUT EXERCISE................................................................................................................................................. 7 2.3 TEST PROCEDURE............................................................................................................................................. 7 2.4 CONFIGURATION OF TESTED SYSTEM............................................................................................................... 7 3. DESCRIPTION OF TEST MODES ..................................................................................................................... 9 4. SUMMARY OF TEST RESULTS....................................................................................................................... 10 5. CONDUCTED EMISSIONS TEST.................................................................................................................... 11 5.1 MEASUREMENT PROCEDURE.......................................................................................................................... 11 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 11 5.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 11 5.4 CONDUCTED EMISSION LIMIT......................................................................................................................... 11 5.5 MEASUREMENT RESULT.................................................................................................................................. 12 5.6 CONDUCTED MEASUREMENT PHOTO.............................................................................................................. 13 6. RADIATED EMISSION TEST ........................................................................................................................... 14 6.1 MEASUREMENT PROCEDURE.......................................................................................................................... 14 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 14 6.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 15 6.4 RADIATED EMISSION LIMIT............................................................................................................................. 15 6.5 MEASUREMENT RESULT................................................................................................…

Text truncated - open the document above for the full version.

Conducted Measurement Photo Radiated Measurement Photos