H4IG54

APPENDIX A1 Compliances Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult an IBM authorized dealer or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM authorized dealers. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment. This device complies with Par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Power Cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded power outlet. IBM power cords used in the United States and Canada are listed by the Underwriters Laborator ies (UL) and certified by the Canadian Standards Association (CSA). A2 For units intended to be operated at 115 volts: Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG, type SVT or SJT, three conductor cord, a maximum of 4.5 meters (15 feet) in length and a parallel blade, grounding type attachment plug rated 15 amperes, 125 volts. For units intended to be operated at 230 volts (U.S. use): Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG, type SVT or SJT, three conductor cord, a maximum of 4.5 meters (15 feet) in length and a tandem blade, grounding type attachment plug rated 15 amperes 250 volts. For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding type attachment plug rated 13 amperes (minimum), 250 volts. The cord set should be marked <HAR> and have the appropriate safety approvals for the country in which the equipment will be installed. As an ENERGY STAR Par tner, IBM Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. MPRII This product compliances with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPRII) for very low frequency (VLF) and extremely low frequency (ELF). Hinweise Gemäß der Amtsblätter des BMPT Nm. 61/1991 und 6/ 1992 wird der Betreiber darauf aufmerksam gemächt, daß die von ihm mit diesem Gerät zusammengestellte Anlange auch den technischen Bestimmungen dieser Amtsblätter genügem muß. Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Unterground zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). ® ® APPENDIX A3 Aus ergonomischen Gründen sollten nur Darstellungen auf dunklem Hintergrund bei Vertikalfrequenzen ab 60 Hz (ohne Zeilensprung) benutzt werden. Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am Ort der Aufstellung aus der korrekten Grundeinstellung veränderm. Zur Korrektur empfiehlt es sich deshalb, die Regler an der Frontseite für H STAT und V STAT so einzustellen, daß die getrennt sichtbaren Farblinien für Rot. Grün und Blau bei z.B. der Darstellung eines Buchstabens zur Deckung (Konvergenz) gelangen. Siehe hierzu auch die Erklärungen zu H STAT und V STAT. European Union (EU) Statement This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 / European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices. Properly shielded and grounded cables and connectors must be used in order to reduce the potential for causing interference to radio and TV communications and to other electrical or electronic equipment. Such cables and connectors are available from IBM authorized dealers. In accordance with EN 50082-1 1992, Performance Criterion A:, it should be noted that in the presence of certain electromagnetic fields, some screen jitter may be observed. Spécifications de la CEE Ce produit a été testé et déclaré conforme aux limites de la Class B définies pour les équipments informatiques conformément à la norme européenne CISPR 22/EN 55022. Les limites imposées aux équipments de Class B visent à garantir une protection raisonnable, dans des environnements résidentiels, contre toute interférence avec des équipements de communication agréés. Des câbles blindés at correctement reliés à la terre doivent être utilisés pour réduire les risques d’interférence avec des communications radio et télévisées, ainsi qu’avec des équipments électriques ou électroniques. Ces câbles et connecteurs sont disponibles auprès de vos revendeurs IBM agréés. Conformément à la …

Text truncated - open the document above for the full version.

ENGLISH English Edition 1 This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or program(s) at any time. It is possible that this publication may contain reference to, or information about, IBM products (machines and programs), programming, or services that are not announced in your country. Requests for copies of this publication and for technical information about IBM products should be made to your IBM Authorized Dealer or IBM Retailer. No part of this publication may be reproduced or distributed in any form or by any means without prior permission in writing from the International Business Machines Corporation. © Copyright International Business Machines Corporation 1999. All rights reserved. Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program or service is not intended to state or imply that only IBM's product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any of IBM's intellectual property rights or other legally protectable rights may be used instead of the IBM product, pro- gram, or service. Evaluation and verification of operation in con- junction with other products, programs, or services, except those expressly designated by IBM, are the user's responsibility. lBM may have patents or pending patent applications covering subject matter in this document. The furnishing of this document does not give you any license to these patents. Trademarks The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States or other countries: IBM HelpCenter E NERGY STA R is a U.S. registered mark. i ENGLISH 1 Contents Contents................................... 1 Setup.........................................2 User controls ...........................5 On-Screen-Display.................. 7 Further information ...............14 Specifications........................16 Troubleshooting....................17 Setup Important:Before connecting the monitor, turn off the computer and attached devices. Also ensure the power at the electrical outlet matches the power requirements of the monitor. Refer to the Specifications section on page 16 for more details. Attaching the Stand 1. Place the monitor face down on a soft surface to prevent the screen being scratched. 2. Insert the hooks (1) into the matching slots on the underside of the monitor (2). 3. Slide the base towards the front of the monitor until the latch (3) clicks into the locked position. 2 ENGLISH Connecting your monitor 1. Connect the signal cable to the video port on the back of your computer (figure A). Your computer may have a video adapter card installed. In this case, attach the signal cable to the connector on the video adapter card (figure B). 2. Connect the power cord to the monitor first, then firmly insert the plug into a properly grounded electrical outlet. 3. Turn on the monitor, and then the computer. If your monitor does not seem to be working correctly, refer to the Troubleshooting section on page 17 for help. 3 B A Workplace preparation Positioning the monitor Choose a suitable place to position the monitor where it is not near fluorescent desk lighting or any equipment that produces magnetic fields that could cause interference. Ensure that the furniture or equipment can support the weight of the monitor. Allow at least 2 inches (50mm) ventilation space around the monitor. Height The monitor should be positioned so that the top of the screen is slightly below your eye level when you sit at your workstation. Orientation Choose a position that gives the least reflection from lights and windows, usually at a right angle to any windows. The monitor should be positioned directly in front of you so that you do not have to twist your body. Tilt the monitor to a comfortable viewing angle. Working Practices Rest Take regular breaks. Vary your posture, and stand up and stretch occasionally as prolonged use of computer workstations can be tiring. Back You should sit back in the chair and use the back rest. Hands Use a light touch on the keyboard, keeping your hands and fingers relaxed. Allow a space in front of the keyboard to rest your wrists when not typing. Consider using a wristpad. Eyesight Working with mpnitors, in common with any prolonged close work, can be visually demanding. Look away from the screen periodically and have your eyesight checked regularly. Screen settings Set the screen brightness and contrast to a comfortable level. You may have to adjust this as the lighting changes during the day. Many application programs let you select colour combinations which can help you to view in comfort. 4 ENGLISH User controls The image is already optimized for many display modes. However, the controls can be used to adjust the image to your liking. nocIlortnoCnoitpircseD .hctiwsrewoP.ffodnanorotinomehtsehctiwS tceleS/DSO.nocilortnoctceles/yalpsiD-neercS-nOehtsetavticA tsartnoC;nwod/thgirevoM noitcelestnemtsujda :snoitcnufowtsahlortnocsihT .noitcelesrofthgirehtotsnocidethgilhgihehtevomoT)1 .detcelesneebsahnocilortnocretfaegamitsujdaotdesuoslA .tsartnocegamiehttsujdaoT)2 ;pu/tfelevoM noitcelestnemtsujdassenthgirB :snoitcnufowtsahlortnocsihT .noitcelesroftfelehtotsnocidethgilhgihehtevomoT)1 .detcelesneebsahnocilortnocretfaegamitsujdaotdesuoslA .ssenthgirbegamiehttsujdaoT)2 tixE .lortnocDSOtixE .devaseblliwputestnerruceht,nottubsihtgnitcelesyb:etoN 5 6 Contrast and Brightness Contrast and Brightness can be adjusted as follows, without the need to display the OSD. Select function and use " " " " control to adjust: If adjustment is not made within 15 seconds, the cur…

Text truncated - open the document above for the full version.

DANGER To avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet. • Any equipment to which this product will be attached must also be connected to properly wired and grounded power outlets. • To isolate the monitor from the electrical supply, you must remove the plug from the power outlet. The power outlet should be easily accessible. Handling: • Your colour monitor is heavy, so handle it with care. IBM recommends that the monitor is moved or lifted by two people. DANGER Pour éviter les risques d’électrocution : • Ne retirez pas les capots du moniteur. • N’utilisez pas ce produit si le socle n’est pas fixé. • Ne connectez, ni ne déconnectez ce produit pendant un orage. • Le câble d’alimentation doit être connecté à une prise électrique correctement mise à la terre et en bon état de marche. • Tout équipement auquel ce produit est relié doit être également connecté à une prise correctement mise à la terre et en bon état de marche. • Pour isoler le moniteur de la source d’alimentation électrique, vous devez le débrancher de la prise électrique. Cette prise doit être facile d’accès Manutention : • Votre moniteur couleurs est lourd et doit donc être manipulé avec soin. IBM vous conseille de le déplacer ou de le porter à deux. ! ! GEFAHRENHINWEIS Um die Gefahr eines elektrischen Schlags zu vermeiden, folgendes beachten: • Unter keinen Umständen die Abdeckungen abnehmen. • Das Produkt nicht in Betrieb nehmen, wenn der Sockel nicht montiert ist. • Das Gerät nicht während eines Gewitters an eine Steckdose anschließen oder von ihr trennen. • Das Netzkabel ist an eine ordnungsgemäß verdrahtete und geerdete Steckdose anzuschließen. • Jedes Gerät, mit dem dieses Produkt verbunden wird, muß ebenfalls an eine ordnungsgemäß verdrahtete und geerdete Steckdose angeschlossen werden. • Um den Monitor von der Stromversorgung zu trennen, muß der Stecker aus der Steckdose gezogen werden. Die Steckdose sollte leicht zugänglich sein. Handhabungshinweis: • Ihr Farbbildschirm ist schwer. Sie sollten daher beim Transport vorsichtig vorgenhen. IBM empfiehlt lhnen, den Bildschirm zu zweit anzuheben. zu tragen. GEVAAR Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen: • Verwijder in geen enkel geval de kap. • Stel dit produkt alleen in werking als de voet is bevestigd. • Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet van een contactdoos tijdens onweer. • Het netsnoer moet worden aangesloten op een geaarde contactdoos met correcte bedrading. • Ook alle apparatuur waarop dit produkt wordt aangesloten moet zijn aangesloten op een contactdoos met correcte bedrading. • Om het beeldscherm te ontkoppelen van de netvoeding, dient u de stekker uit de contactdoos te trekken. De contactdoos dient goed toegankelijk te zijn. Verplaatsing: • uw kleurenmonitor is zwaar, ga er dus voorzichtig mee om. IBM raadt aan dat het tillen of verplaatsen ervan door twee mensen gebeur t. ! ! PELIGRO Para evitar riesgos de descargas eléctricas: • No retire bajo ningún concepto las cubier tas. • No maneje el monitor sin antes acoplar el soporte. • No conecte ni desconecte el equipo de una toma de alimentación durante una tormenta eléctrica. • El cable de alimentación debe estar conectado a un enchufe debidamente cableado y con toma de tierra. • Cualquier equipo al que se vaya a conectar este producto también debe estar conectado a tomas de alimentación cableadas y conectadas a tierra correctamente. • Para aislar el monitor del suministro eléctrico, debe retirar el enchufe de la toma de alimentación. Esta toma deberá ser de fácil acceso. Movimentazione del monitor: • Il monitor a colori è pesante, si consiglia quindi di maneggiarlo con attenzione. IBM raccomanda che il monitor venga mosso o sollevato da due persone. PERICOLO Per evitare il rischio di scariche elettriche: • Non rimuovere nessuna par te del telaio. • Non accendere il prodotto se il piedistallo non è stato montato. • Non collegare o scollegare il prodotto nel corso di un temporale. • La spina del cavo di alimentazione deve essere collegata ad una presa di corrente con messa a terra, installata in maniera appropriata. • Le apparecchiature a cui il prodotto viene attaccato devono essere collegate a prese di corrente con messa a terra, installate in maniera appropriata. • Per isolare il monitor dalla corrente elettrica, staccare la spina dalla presa di alimentazione, che deve essere facilmente accessibile. Manipulación: • El monitor de color es pesado, por lo que debe manipularlo con cuidado. Si pesa más de 18 kg, IBM recomienda moverlo con la ayuda de dos personas. ! ! PERIGO Para evitar o perigo de choques eléctricos: • Não retire as coberturas. • Não utilize este produto antes de montar a base. • Não ligue nem desligue este produto durante uma tempestade eléctrica. • O cabo de alimentação deve ser ligado a uma tomada eléctrica devidamente ligada à terra. • Qualquer equipamento ligado a este produto deve estar ligado a tomadas eléctricas devidamente ligadas à terra. • Para isolar o monitor da fonte de alimentação, retire a ficha do cabo de alimentação da tomada eléctrica. A tomada eléctrica deve ser de fácil acesso. Manuseio: • Seu monitor colorido é pesado, então manuseie-o com cuidado. A IBM recomenda que o monitor seja movido ou carregado por duas pessoas. FARE Sådan undgår du elektrisk stød: • Kabinettet må under ingen omstaendigheder fjernes. • Undgå at anvende dette produkt, uden at vippe/drejefoden er monteret. • Undgå at tilslutte eller frakoble dette produkt i tordenvejr. • Netledningen skal vaere tilsluttet en korrekt jordet stikkontakt med korrekt ledningsføring. • Alt udstyr, som tilsluttes dette produkt, skal også vaere tilsluttet korrekt jordede stikkontakter med korrekt ledningsføring. • For at isolere skae…

Text truncated - open the document above for the full version.

FCC ID:H4IG54

FCC ID : H4IG54Front side of EUT Number 1 962518-01.JPG FCC ID : H4IG54Rear side of EUT (Reference Modification No.1) Number 2 962518-02.JPG 1 1 FCC ID : H4IG54Mechanical Construction Number 3 962518-03.JPG FCC ID : H4IG54Mechanical Construction (Reference Modification No.2,3) Number 4 962518-04.JPG 2 3 FCC ID : H4IG54Mechanical Construction Number 5 962518-05.JPG FCC ID : H4IG54Mechanical Construction Number 6 962518-06.JPG FCC ID : H4IG54Mechanical Construction Number 7 962518-07.JPG FCC ID : H4IG54Mechanical Construction Number 8 962518-08.JPG FCC ID : H4IG54Mechanical Construction Number 9 962518-09.JPG FCC ID : H4IG54Mechanical Construction (Reference Modification No.4,5,6,7,8) Number 10 962518-10.JPG 8 7 4 5 6 FCC ID : H4IG54Mechanical Construction Number 11 962518-11.JPG FCC ID : H4IG54Mechanical Construction Number 12 962518-12.JPG FCC ID : H4IG54Mechanical Construction Number 13 962518-13.JPG FCC ID : H4IG54Front side of main board (Reference Modification No.9) Number 14 962518-14.JPG 9 FCC ID : H4IG54Rear side of EUT Number 15 962518-15.JPG FCC ID : H4IG54Rear side of main board (Reference Modification No.10) Number 16 962518-16.JPG 10 FCC ID : H4IG54Rear side of main board Number 17 962518-17.JPG FCC ID : H4IG54Front side of CRT board Number 18 962518-18.JPG FCC ID : H4IG54Rear side of CRT board Number 19 962518-19.JPG

FCC ID LABEL LOCATION 962518-20.JPG

FCC TEST REPORT REPORT NO. : F962518 SPORTON International Inc. FCC ID : H4IG54 TEL : 886-2-2696-2468PAGE NUMBER : 1 OF 24 FAX : 886-2-2696-2255ISSUED DATE: Jul. 09, 1999 FCC TEST REPORT for CISPR PUB.22 CLASS B Equipment: 15” Monitor MODEL NO.: G54 MACHINE TYPE : 6546-02N, 6546-92N FCC ID : H4IG54 Filing Type: Original Certification APPLICANT:LITE-ON TECHNOLOGY CORP. 5F, 16, Sec. 4, Nanking E. Rd., Taipei, Taiwan, R.O.C.
The test result refers exclusively to the test presented test model / sample.
Without the written authorization of the test lab., the Test Report may not be copied.
Certificate or Test Report must not be used by the applicant to claim the product in this test report endorsement by NVLAP or any agency of the U.S Government. SPORTON INTERNATIONAL INC. 6F, No. 106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. FCC TEST REPORT REPORT NO. : F962518 SPORTON International Inc. FCC ID : H4IG54 TEL : 886-2-2696-2468PAGE NUMBER : 2 OF 24 FAX : 886-2-2696-2255ISSUED DATE: Jul. 09, 1999 TABLE OF CONTENT SECTION TITLEPAGE CERTIFICATE OF COMPLIANCE ...................................................................................................................... 3 1. GENERAL DESCRIPTION OF EQUIPMENT UNDER TEST ......................................................................... 4 1.1. APPLICANT ...................................................................................................................................................................................4 1.2. MANUFACTURER .........................................................................................................................................................................4 1.3. BASIC DESCRIPTION OF EQUIPMENT UNDER TEST................................................................................................................4 1.4. FEATURE OF EQUIPMENT UNDER TEST ...................................................................................................................................4 2. TEST CONFIGURATION OF EQUIPMENT UNDER TEST............................................................................ 5 2.1. TEST MANNER .............................................................................................................................................................................5 2.2. DESCRIPTION OF TEST SYSTEM ...............................................................................................................................................5 2.3. CONNECTION DIAGRAM OF TEST SYSTEM ..............................................................................................................................7 3. TEST SOFTWARE .......................................................................................................................................... 8 4. GENERAL INFORMATION OF TEST............................................................................................................. 9 4.1. TEST FACILITY .............................................................................................................................................................................9 4.2. STANDARD FOR METHODS OF MEASUREMENT ......................................................................................................................9 4.3 .TEST IN COMPLIANCE WITH.......................................................................................................................................................9 4.4. FREQUENCY RANGE INVESTIGATED ........................................................................................................................................9 4.5. TEST DISTANCE...........................................................................................................................................................................9 5. TEST OF CONDUCTED POWERLINE......................................................................................................... 10 5.1. MAJOR MEASURING INSTRUMENTS........................................................................................................................................10 5.2. TEST PROCEDURES..................................................................................................................................................................11 5.3. TYPICAL TEST SETUP LAYOUT OF CONDUCTED POWERLINE ............................................................................................12 5.4. TEST RESULT OF AC POWERLINE CONDUCTED EMISSION .................................................................................................13 5.5. PHOTOGRAPHS OF CONDUCTED POWERLINE TEST CONFIGURATION .............................................................................15 6. TEST OF RADIATED EMISSION.................................................................................................................. 15 6.1. MAJOR MEASURING INSTRUMENTS........................................................................................................................................17 6.2. TEST PROCEDURES..................................................................................................................................................................18 6.3. TYPICAL TEST SETUP LAYOUT OF RADIATED EMISSION .....................................................................................................19 6.4. TEST RESULT OF RADIATED EMISSION..................................................................................................................................20 6.5. PHOTOGRAPHS OF RADIATED EMISSION TEST CONFIGURATION......................................................................................22 7. ANTENNA FACTOR AND CABLE LOSS..................................................................................................... 22 8. LIST OF MEASURING INSTRUMENTS USED ......…

Text truncated - open the document above for the full version.