H8N-RTF3026VWD25GPON ONT

1 I-241W-U User’s Manual with product spec. 2 History Page Date Version Description Author 2013/01/29 V0 Initial editing. Kevin Huang 3 Feature Description: Overview 1 Introduction The I-241W-U is a GPON ONT which supports  4 Gigabit Ethernets  2 POTS  2 Wi-Fi (2.4G & 5G)  1 HomePNA  2 USB  1 GPON WAN port (32 GEM ports, 128 TCONTs) Either pure RG model or pure ONT model is supported at one time by downloading different software releases. In this document, we will briefly introduce the feature of pure RG model and pure ONT model. The more detailed information please refers to related documents. 2 Pure ONT model release With pure ONT model release, I-241W-U will report to OLT that it contains one Ethernet slot with 4 GE ports, HomePNA and one POTS slot with 2 ports as Figure 1 shown. The Wi-Fi module and USB module are disabled in this mode. I -241 W-U GPON L2 ONT GPON ODN OLT OMCI IPHost VOIP POTS0 POTS1 WiFI USB ETh0 ETh1 Eth2 Eth3 HPNA Figure 1 I-241W-U provides VOIP service and L2 bridging service including Multicast service. They are all controlled by OLT. 4 2.1 VoIP The IP Host interface is dedicated for VOIP service. Single VLAN id could be assigned but different p-bits/DSCP could be assigned for SIP control packets and VOIP data. ALU’s SIP protocol is ported for I-241W-U. VOIP related parameters could be configured through OMCI protocol and downloading VOIP XML file to I-241W-U. 2.2 L2 VLAN tagging, VLAN/p-bit transparent and VLAN/p-bit translation are all supported in each Ethernet port and following OLT VLAN modes could be supported.  C-VLAN cross-connect  S+C-VLAN cross-connect  S-VLAN tunnel cross-connect  C-VLAN residential-bridge 2.3 Multicast IGMP snooping is supported and 64 multicast groups. 3 Pure RG model release With RG model release, it will report to OLT that it contains one VEIP slot with single port and one POTS slot with 2 ports as Figure 2 shown. Broadband Network I-241W-U GPON L2 ONTRGW GPON Virtual Eth ODN OLT ACS CPE WAN Management Protocol (TR069) OMCI ETh0 ETh1 Eth2 Eth3 IPHost VOIP POTS0 POTS1 WiFI USB HPNA Figure 2 I-241W-U provides VOIP service and L3 routing service including Multicast service. In current release, VOIP service is still controlled by OMCI not TR-069. Besides 5 VOIP service, OLT only configures L2/Multicast information for VEIP interface and leaves routing service to ACS’s business. 3.1 VoIP The same as pure ONT release. Please see section 2.1. 3.2 VEIP The OLT must configure all the VLAN/p-bit used by different services: HSI, IPTV, Management and VOIP. (The VOIP interface is reserved for future ACS-controlled VOIP service. In currently release, it is not supported yet.). Also, the Multicast channel VLAN used for IPTV service. It should treat the virtual Ethernet interface just like an Ethernet Port to allow the traffic coming RGW could pass OLT correctly. After OLT has well configured the L2 path for VEIP interface, the RG service could be controlled by remote ACS via TR069 protocol. Before ACS could reach I-241W-U, one WAN connection used to connect to ACS server and ACS server information must be configured first in I-241W-U to make sure I-241W-U could communicate with remote ACS and it could be configured by local management interface: Web and TR-064. 3.3 RG interfaces Basically, the embedded RG in I-241W-U provides up to two LAN interfaces and up to 4 WAN connections in WAN side and it is shown in following figure. Figure 3 6 3.3.1 WAN interface In WAN side, up to 4 WAN connections for following services are supported.  HIS: Internet service  IPTV: VoD and Multicast service  Management: remote management of TR-069 (ACS server)  VOIP: ACS controlled VOIP service. (Currently, it’s not supported yet) Only HSI and IPTV interfaces used for routing service for LAN devices. Traffic of other interfaces is terminated in I-241W-U. IPoE and PPPoE could be configured for each interface, except IPTV interface does not support PPPoE mode. Addressing of each interface is individual. Different IP address, gateway and DNS servers could be retrieved by each interface and used for respective service. Since both HSI interface and IPTV interface provide routing service for LAN users, either the gateway of HSI interface or that of IPTV interface must be selected to be the default gateway for routing traffic and both DNS servers of two interfaces must be used for DNS queries coming from LAN side. Only HSI interface supports IPv6. 3.3.2 LAN interface There is a main interface (called home network interface) used for home network including 4 Ethernet ports, Dual-band Wi-Fi APs, HomePNA and 2 USB ports. I-241W-U provides an extra LAN interface (called guest network interface) for Wi-Fi guest, there is only one Wi-Fi AP of this extra LAN interface. I-241W-U forbids the traffic between two LAN interfaces, so the packets can not be forwarded between home network interfaces and guest network interfaces. 3.3.2.1 LAN interface for Home Network (Home Network Interface) All interfaces (4 Ethernet ports, 2 Wi-Fi APs, HomePNA, 2 USB ports ) are bridged. The user belonging to home network could reach each other and also use HSI/IPTV service. The Web/TR-064 could be used to manage I-241W-U from LAN side. I-241W-U also supports UPnP IGD and DLNA service. IPv6 is supported for home network also. 3.3.2.2 LAN interface for Wi-Fi Guest Network (Guest Network Interfaces) In order to provide Dual-band Wi-Fi guest network for visitors and protect home network security, an extra LAN interface is provided and two Wi-Fi APs are attached 7 to these 2.4G and 5G interface. Visitors can access HSI/IPTV service just like home network by Wi-Fi, but they are forbidden to access I-241W-U management interface. UPnP IGD and DLNA service are not supported for Wi-Fi guest network. 3.4 Multicast service IGMP snooping is supported for home network interface and IGMP proxy is supported in WAN IPTV interface. I-241W-U does not support multicast service on guest network interface. 8 I-…

Text truncated - open the document above for the full version.

40 Figure 21 6.9.2 IPv4 in IPv6 In this page, you can add or remove IPv6 in IPv4. Figure 22 6.10 IPsec Tunnel In this page, you can add or remove IPSec Tunnel. 41 Figure 23 6.11 QoS In this page, you can add or remove QoS and modify status of QoS. Figure 24-1 In this section, you can set DSCP and P-bit mapping table, press “Apply/Save”. 42 Figure 24-2 6.12 IGMP Proxy In this page, you can set parameters of IGMP proxy, press “Apply/Save”. 43 Figure 25-1 In this section, you can add or remove IGMP profile and allowed host, and refresh or reset statistic. 44 Figure 25-2 6.13 WLAN 6.13.1 Basic/Security In this page, you can enable or disable wireless and set parameters of basic part, press “Apply/Save”. 45 Figure 26-1 In this section, you can set parameters of security part, press “Apply/Save”. 46 Figure 26-2 This section show statistics of wlan interface. 47 Figure 26-3 6.13.2 WDS In this page, you can see Remote Bridges MAC Address and set parameters of WDS, press “Apply/Save”. 48 Figure 27 6.13.3 Scheduling In this page, you can enable or disable scheduling and set active times, press “Apply/Save”. Figure 28 49 6.13.4 Advanced In this page, you can set parameters of advanced, press “Apply/Save”. Figure 29-1 50 Figure 29-2 6.13.4.1 Change Wireless Band In this page, you can change wireless band, select “Band”. Figure 29-3 51 Change wireless band complete! Figure 29-4 6.13.5 Virtual Access Point In this page, you can enable or disable guest, set parameters of guest, press “Apply/Save”. Figure 30 52 6.13.6 Station Info In this page, you can see the status of authentication in system. Figure 31 6.14 USB Device In this page, you can see information of USB device. You can see the status of USB dongle and link to web page if there is a USB dongle insert in system. You also can add or remove user account of USB device. Figure 32 53 6.15 UPnP In this page, you can enable or disable UPnP function. Figure 33 6.16 DLNA In this page, you can enable or disable DLNA function. Figure 34-1 If enabled, you can input path, press “Apply/Save”. 54 Figure 34-2 7 Support VoIP 7.1 Hook Status In this page, you can see the status of hook. Figure 35 7.2 SIP Status In this page, you can see the status of SIP. 55 Figure 36 8 Support Diagnosis 8.1 Ping Test In this page, you can input host name or ip address for ping test, both IPv4 and IPv6 supported. The result of ping test will show in page. Figure 37 8.2 Traceroute Test In this page, you can input host name or ip address for trace route test, both IPv4 and IPv6 supported. The result of trace route test will show in page. 56 Figure 38 9 Management 9.1 System In this page, you can set the interval of time out, WEB will logout when the time of login is expired. 57 Figure 39-1 In this page, you can set parameters of TR-064, TR-069, press “Apply/Save”. 58 Figure 39-2 In this section, you can enable or disable NTP, and set time server and time zone, press “Apply/Save”. 59 Figure 39-3 9.2 Setting In this page, you can backup configuration, load configuration, restore to default. 60 Figure 40-1 In this section, you can add or remove CA which is used for TR-069 management. 61 Figure 40-2 9.3 System Log In this page, you can set rule of system log and display system log in system. Figure 41 62 9.4 Update Software (for “tech” only) In this page, you can update software image to system. Figure 42 9.5 Access Control In this page, you can modify password, press “Appy/Save”, Figure 43-1 63 In this page, you can enable or disable Temp Wan connection function. Figure 43-2 9.6 Reboot In this page, you can reboot system. Figure 44 64 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. 65 FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Declaration for no non-US channel operation August 28, 2013 We, Askey Computer Corp, declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: H8N-RTF3026VWD25 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-28 FCC ID: H8N-RTF3026VWD25 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to DA 04-1705 of the commission’s public notice, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-15 FCC ID: H8N-RTF3026VWD25 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the publ.ic. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, .1:,I~ Ct.-" -~~----------~--- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-15 FCC ID: H8N-RTF3026VWD25 A U T H O R I Z A T I O N L E T T E R To whom it may concern: We, the undersigned Askey Computer Corp hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15C & 15E and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, John Chiou Director Askey Computer Corp

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4

Linda_Wu V6 1510 Paper / Other RTF3026VW-D25(RoHS) 50#白色特多龍(亮面) +壓花膠 Label(外購+自印) Notes: 1.供應商: 華冠 2.被貼物材質: ABS 3.Size: 69.5*49.5 mm(0.5R*3,右下角3C) 4.PGJI2的UL原材代碼: CM-100-KPT 5.碳帶型號: B110C V1New 2012/09/28 Change ONT APN: 3FE55075AAAA ONT SN:ALCLF4AXXXXX 2012/10/18 Delete C-tick / Add Wi-Fi Logo 2013/08/06 Add Logo2013/08/07 V2 V3 V4 Change FCC ID:H8N-RTF3026VWD25 2013/08/14 V5 Add 2013/08/22 V6 PART NO. DRAFTER PART NAME MODEL NO. MATERIAL 材質 代號 Product Unit 2013.08.22 69.5mm 100% 0.5R*3 3C*1 9mm 9.6mm 49.5mm 2 2 GPON ONT Model: I-241W-U ONT APN: 3FE55075AAAA ICS: XX Mrev: XX MFD: YYMM 廠內自印部分 2301 Sugar Bush Rd., Raleigh, NC 27612 50 5mm 5.5mm 6mm 5mm 7mm Mac: XXXXXXXXXX ONT SN:ALCLF4AXXXXX Pastes here 請注意：認證尚未完成，Lable不能貼于機器上！ FCC ID: H8N-RTF3026VWD25 Rating: 12V 2.5A ASSEMBLED IN: CHINA CLASS 1 LASER PRODUCT This Product Contains Class 1 Laser Transmitters That Are Certified By Their Manufacturers According To 21 CFR Subchapter J. This Class (B) digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada. FACTORY ID: 2 50 x

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5

FCC ID: H8N-RTF3026VWD25 Report No.: RF130724C01 Operational Description This device is a GPON ONT, which operates in 2.4GHz & 5.0GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 12Vdc from AC adapter. The antenna is Printed without antenna connector. The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA130715C31 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130715C31 MODEL NO.: I-241W-U FCC ID: H8N-RTF3026VWD25 RECEIVED: Jul. 15, 2013 TESTED: Aug. 02 ~ Aug. 15, 2013 ISSUED: Aug. 19, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. Report No.: SA130715C31 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 3 1. CERTIFICATION .......................................................................................................... 4 2. RF EXPOSURE ........................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ..................................... 5 2.2 MPE CALCULATION FORMULA................................................................................. 5 2.3 CLASSIFICATION ....................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .............................. 6 Report No.: SA130715C31 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130715C31 Original release Aug. 19, 2013 Report No.: SA130715C31 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: GPON ONT MODEL NO.: I-241W-U BRAND: Alcatel-Lucent APPLICANT: Askey Computer Corp TESTED: Aug. 02 ~ Aug. 15, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: I-241W-U) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Aug. 19, 2013 Maggie Wu / Specialist APPROVED BY: , DATE :Aug. 19, 2013 Ken Liu / Senior Manager Report No.: SA130715C31 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130715C31 6 of 6 Report Format Version 5.0.0 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 29.55 3.35 20 0.388 1 5180-5240 26.79 4.38 20 0.260 1 5745-5825 16.88 4.38 20 0.027 1 ---END---

Report No.: RF130715C31 1 of 105 Report Format Version 5.2.0 FCC TEST REPORT (15.247) REPORT NO.: RF130715C31 MODEL NO.: I-241W-U FCC ID: H8N-RTF3026VWD25 RECEIVED: Jul. 15, 2013 TESTED: Aug. 02 ~ Aug. 15, 2013 ISSUED: Aug. 19, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130715C31 2 of 105 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 5 1. CERTIFICATION .......................................................................................................... 6 2. SUMMARY OF TEST RESULTS ................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ............................................................................... 7 3. GENERAL INFORMATION .......................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ............................................................................ 8 3.2 DESCRIPTION OF TEST MODES ............................................................................ 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................ 11 3.3 DESCRIPTION OF SUPPORT UNITS ...................................................................... 15 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ....................................................... 16 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................... 17 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ................................................ 18 4.1 RADIATED EMISSIONS AND BANDEDGE MEASUREMENT ................................. 18 4.1.1 LIMITS OF RADIATED EMISSIONS AND BANDEDGE MEASUREMENT ............... 18 4.1.2 TEST INSTRUMENTS ............................................................................................... 19 4.1.3 TEST PROCEDURES ............................................................................................... 20 4.1.4 DEVIATION FROM TEST STANDARD...................................................................... 20 4.1.5 TEST SETUP ............................................................................................................. 21 4.1.6 EUT OPERATING CONDITIONS .............................................................................. 21 4.1.7 TEST RESULTS ........................................................................................................ 22 4.2 CONDUCTED EMISSIONS MEASUREMENT .......................................................... 41 4.2.1 LIMITS OF CONDUCTED EMISSIONS MEASUREMENT ....................................... 41 4.2.2 TEST INSTRUMENTS ............................................................................................... 41 4.2.3 TEST PROCEDURES ............................................................................................... 42 4.2.4 DEVIATION FROM TEST STANDARD...................................................................... 42 4.2.5 TEST SETUP ............................................................................................................. 42 4.2.6 EUT OPERATING CONDITIONS .............................................................................. 42 4.2.7 TEST RESULTS ........................................................................................................ 43 4.3 6dB BANDWIDTH MEASUREMENT ......................................................................... 45 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ..................................................... 45 4.3.2 TEST SETUP ............................................................................................................. 45 4.3.3 TEST INSTRUMENTS ............................................................................................... 45 4.3.4 TEST PROCEDURE .................................................................................................. 45 4.3.5 DEVIATION FROM TEST STANDARD...................................................................... 45 4.3.6 EUT OPERATING CONDITIONS .............................................................................. 45 4.3.7 TEST RESULTS ......…

Text truncated - open the document above for the full version.

Report No.: RF130715C31-1 1 of 61 Report Format Version 5.2.0 FCC TEST REPORT (15.407) REPORT NO.: RF130715C31-1 MODEL NO.: I-241W-U FCC ID: H8N-RTF3026VWD25 RECEIVED: Jul. 15, 2013 TESTED: Aug. 02 ~ Aug. 15, 2013 ISSUED: Aug. 19, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the rep…

Text truncated - open the document above for the full version.