H8N-TBT1700Tablet

Tablet Photon 100 User Manual Thank you for choosing BungBungame Tablet. This manual covers the basic features and functions of the Tablet and is aimed at enhancing your experience of using the product. For more information, please visit BungBungame’s website at www.bungbungame.com or access and save the User Manual (complete version) on the Tablet. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. BungBungame Tablet Introduction BungBungame Tablet Buttons and Ports Camera Flash Ports: USB port, mini HDMI socket Vent Charge port Speaker ports 1 2 3 4 5 6 Back view 1 2 3 4 5 6 4 1 2 Front view Right view Left view Ports: USB and mini HDMI Volume: ＋Increase, －Decrease mini HDMI and mini Micro SD Earphone jack BungBungame Tablet Buttons and Ports 1 2 1 2 3 4 3 4 Power button Switch between applications and rotate the screen Speaker ports 40-pin connector (AC adapter jack/auxiliary component jack) Top view Bottom view BungBungame Tablet Buttons and Ports Press and release: Fast switch between applications (Stay at the current page). Hold for 4 seconds: Lock rotated images. Hold for 4 seconds again: Unlock rotated images. 1 2 3 4 3 4 1 2 3 Step 1 Check the components of the Tablet Step 2 Set up your Tablet for the first time User Manual Power lead Adapter BungBungame Tablet Buttons and Ports Connect the adapter to the power socket. Connect the power lead to the adapter and then to the mains. Press the power button to start the Tablet. 1 2 3 3 1 2 BungBungame Tablet Important Note NB Please follow the instructions Please follow the instructions in the Manual to protect your Tablet from potential damage and to help to ensure your personal safety. Recovery system NB Please back up your recovery system in advance to prepare for the following situations: • When your computer system is highly unstable and breaks down all the time, or when you cannot access the Windows system or the user interface, or cannot get rid of a virus. • If you need the recovery system but did not create a recovery disc before, please contact your dealer or the manufacturer for more help. • If you need the recovery system while the hard disk is damaged but did not create a recovery disc before, please contact the manufacturer for more help. Environmental Protection NB You are urged to recycle or dispose this product and related components (e.g. batteries, power leads) properly in accordance to regulations in your community when it has outlived its useful life. By doing this, you can help improve the environment as well as minimize the potential negative effects caused by the waste material. For more information about how to dispose the product properly, please contact your dealer or your local authorities. Certificate of Authenticity (COA) of Microsoft Windows 7 software Dear customers, Genuine Microsoft Windows 7 software has been implemented on the Tablet with a sticker attached to the inside of the battery cover to prove its authenticity. NB BungBungame Tablet is powered by a non-removable battery. Please do not try to dissemble or remove the battery to prevent breakdowns of the device. BungBungame Tablet Important Note If you need the Certificate of Authenticity (COA) of Microsoft Windows 7 software, please go to Control Panel  System and Security  Systems in the Tablet. You will find the information you need at the bottom of the page (illustrated below). Important issues of battery NB BungBungame Tablet is powered by a non-removable battery. Please do not try to dissemble or remove the battery to prevent breakdowns of the device. If the battery fails and needs further troubleshooting, please contact the manufacturer for further help. NB To optimise your battery’s life and performance and to protect your personal safety, please use the battery in proper temperatures (between 15 °C - 25°C) and avoid extreme temperatures that might harm the performance of the battery as well as cause a breakdown of the product or other safety concerns. xxxxx-xxx-xxxxxxx-xxxxx BungBungame Tablet Important Note NB When battery charge display shows that the battery is low, follow the steps below immediately to avoid data loss caused by the automatic shutdown of the Tablet: 1.Save all files you want to keep. 2.Connect the adapter to the mains and then to the Tablet. Then you can use your Tablet on the mains while you wait for the battery to charge. 3.If y…

Text truncated - open the document above for the full version.

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 Declaration for no non-US channel operation We, Askey Computer Corp declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: H8N-TBT1700 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- John Chiou / Director

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 Date: 2011-11-09 FCC ID: H8N-TBT1700 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ___________________________________ John Chiou / Director

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 Date: 2011-11-09 A U T H O R I Z A T I O N L E T T E R To whom it may concern: We, the undersigned Askey Computer Corp hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15C and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------ John Chiou / Director

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5

Emma_Feng Paper / Other TBT1700-D13(RoHS) Label(安規/認證) 50#特多龍 PART NO. DRAFTER PART NAME MODEL NO. MATERIAL 材質 代號 Product Unit Notes: 1.供應商: 2.被貼物材質:carbon(碳纖維) 3.黏貼位置:機殼表面 5mm5mm 7mm AAABBbCCDDDD AAABBbCCDDDD AAABBbCCDDDD AAABBbCCDDDD KCC-XXX-MIN-XXXXXXXXX KCC-XXX-MIN-XXXXXXXXX 1510- V1New 2011/10/17 CCXXxxYYyyyZzW BungBungame Model : Photon 100 Input : BungBungame Inc. All rights reserved. Rm. 511, 5F., Building E, No.19-13, Sanchong Rd., Nangang Dist., Taipei City 11501, Taiwan (R.O.C.) Made in China E188325 19V2.1A, 40WA/XXXXXE FCC ID: H8N-TBT1700 2 V5 100.11.04 V2 BungBungame Technology Co., Ltd. BungBungame Inc. 2011/10/19 V3 2011/10/20 V4 R31436 2011/11/03 V5 FCC ID H8N-TBT1700 2011/11/04 R31436 4.PGJI2的UL原材代碼: 5.碳帶型號: 6.Pantone cool gray9c印刷 1.2 0.5R*4 55 33 2.3

Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20

FCC ID: H8N-TBT1700 Report No.: RF111031C30 OPERATIONAL DESCRIPTION WLAN Part: This device is a Tablet, which operates in 2.4GHz band, the maximum data rate could be up to 150Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. BT Part: The modulation is GFSK,π/4-DQPSK, 8DPSK. The device adopts Frequency Hopping Spread Spectrum technology (FHSS). The transmitter of the EUT is powered by 19Vdc from the host equipment or the power adapter, and DC 11.1 from the battery. The antenna is PIFA antenna with IPEX antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: SA111031C30-1 1 Report Format Version 4.1.0 RF EXPOSURE REPORT (FOR BLUETOOTH) REPORT NO.: SA111031C30-1 MODEL NO.: Photon 100 FCC ID: H8N-TBT1700 RECEIVED: Oct. 31, 2011 TESTED: Nov. 02 ~ Nov. 04, 2011 ISSUED: Nov. 11, 2011 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 5 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA111031C30-1 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD...............................................................................................3 1. CERTIFICATION ...........................................................................................................4 2. REDUCED CONDITION FOR SAR ...............................................................................5 3. MAXIMUM MEASURED POWER OF EUT ...................................................................5 4. CONCLUSION...............................................................................................................5 Report No.: SA111031C30-1 3 Report Format Version 4.1.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Nov. 11, 2011 Report No.: SA111031C30-1 4 Report Format Version 4.1.0 1. CERTIFICATION PRODUCT: Tablet MODEL: Photon 100 BRAND: BungBungame APPLICANT: Askey Computer Corp TESTED: Nov. 02 ~ Nov. 04, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: Photon 100) have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Nov. 11, 2011 Ivy Lin/ Specialist APPROVED BY : , DATE:Nov. 11, 2011 Gary Chang / Technical Manager Report No.: SA111031C30-1 5 Report Format Version 4.1.0 2. REDUCED CONDITION FOR SAR When output power is ≤ 60/f(GHz) mW, SAR evaluation is not required. 3. MAXIMUM MEASURED POWER OF EUT Mode Conducted power (dBm) Antenna Gain (dBi) EIRP (dBm) Threshold for SAR (dBm) Bluetooth 0.01 2.29 2.30 13.84 4. CONCLUSION No SAR evaluation is required since output power of EUT is less than threshold of SAR.

Report No.: SA111006C11 1 Report Format Version 4.0.0 FCC SAR TEST REPORT REPORT NO.: SA111031C30 MODEL NO.: Photon 100 FCC ID: H8N-TBT1700 RECEIVED: Oct. 31, 2011 TESTED: Nov. 07, 2011 ISSUED: Nov. 10, 2011 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 24 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: SA111006C11 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................................................3 1. CERTIFICATION .............................................................................................................................4 2. GENERAL INFORMATION..............................................................................................................5 2.1 GENERAL DESCRIPTION OF EUT................................................................................................5 2.2 GENERAL DESCRIPTION OF APPLIED STANDARDS.................................................................6 2.3 GENERAL INOFRMATION OF THE SAR SYSTEM .......................................................................7 2.4 TEST EQUIPMENT .......................................................................................................................10 2.5 GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION ....................................11 3. RECIPES FOR TISSUE SIMULATING LIQUIDS..........................................................................15 4. SYSTEM VALIDATION ..................................................................................................................17 4.1 TEST PROCEDURE......................................................................................................................17 4.2 VALIDATION RESULTS ................................................................................................................18 4.3 SYSTEM VALIDATION UNCERTAINTIES ....................................................................................19 5. TEST RESULTS ............................................................................................................................20 5.1 TEST PROCEDURES ...................................................................................................................20 5.2 MEASURED SAR RESULTS ........................................................................................................22 6. SAR LIMITS...................................................................................................................................23 7. INFORMATION ON THE TESTING LABORATORIES..................................................................24 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION Report No.: SA111006C11 3 Report Format Version 4.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release N/A Nov. 10, 2011 Report No.: SA111006C11 4 Report Format Version 4.0.0 1. CERTIFICATION PRODUCT: Tablet MODEL NO.: Photon 100 FCC ID: H8N-TBT1700 BRAND: BungBungame APPLICANT: Askey Computer Corp TESTED: Nov. 07, 2011 STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE 1528-2003 KDB 447498 D01 v04 KDB 248227 D01 v01r02 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. PREPARED BY : , DATE :Nov. 10, 2011 Ivonne Wu / Senior Specialist APPROVED BY : , DATE :Nov. 10, 2011 Roy Wu / Manager Report No.: SA111006C11 5 Report Format Version 4.0.0 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT EUT Tablet MODEL NO. Photon 100 FCC ID H8N-TBT1700 CLASSIFICATION Engineering Sample MODULATION TYPE CCK, DQPSK, DBPSK for DSSS 64QAM, 16QAM, QPSK, BPSK for OFDM MODULATION TECHNOLOGY DSSS, OFDM TRANSFER RATE 802.11b:11/5.5/2/1Mbps 802.11g: 54/48/36/24/18/12/9/6Mbps 802.11n: MCS0-15 OPERATING FREQUENCY 2412 ~ 2462MHz MAX. SAR (1g) 0.708 W/kg ANTENNA TYPE PIFA antenna NOTE: 1. The EUT provides one completed transmitter and one receiver. MODULATION MODE TX FUNCTION 802.11b 1TX 802.11g 1TX 802.11n (20MHz) 1TX 802.11n (40MHz) 1TX Report No.: SA111006C11 6 Report Format Version 4.0.0 2. The EUT Conducted average power(dBm) listed as below: Mode 802.11b 802.11g Data Rate 1M 6M Channel 1 6 11 1 6 11 Frequency 2412 2437 2462 2412 2437 2462 Avg. Power 16.10 17.20 17.30 11.20 17.50 13.10 Peak. Power 18.30 19.30 19.30 19.50 23.50 20.40 Mode 802.11n 20M 802.11n 40M Data Rate MCS0 MCS0 Channel 1 6 11 3 6 9 Frequency 2412 2437 2462 2422 2437 2452 Avg. Power 10.40 16.50 12.60 9.70 12.30 11.20 Peak. Power 18.80 22.80 20.20 18.50 20.70 20.20 According to KDB 248227, WLAN SAR was performed at the lowest data rate. 3. The above EUT information is declared by manufacturer and for more detailed feature description, please refer to the manufacturer's specifications or User's Manual. 2.2 GENERAL DESCRIPTION OF APPLIED…

Text truncated - open the document above for the full version.

Report No.: RF111031C30 1 Report Format Version 4.1.0 FCC TEST REPORT REPORT NO.: RF111031C30 MODEL NO.: Photon 100 FCC ID: H8N-TBT1700 RECEIVED: Oct. 31, 2011 TESTED: Nov. 01 ~ Nov. 09, 2011 ISSUED: Nov. 11, 2011 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 50 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF111031C30 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................4 1. CERTIFICATION .........................................................................................................5 2. SUMMARY OF TEST RESULTS .................................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................................6 3. GENERAL INFORMATION..........................................................................................7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................7 3.2 DESCRIPTION OF TEST MODES ..............................................................................9 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................10 3.2.2 DESCRIPTION OF SUPPORT UNITS ......................................................................10 3.2.3 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................ 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ...........................................13 4. TEST TYPES AND RESULTS ...................................................................................14 4.1 RADIATED EMISSION MEASUREMENT .................................................................14 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................................14 4.1.2 TEST INSTRUMENTS...............................................................................................15 4.1.3 TEST PROCEDURES ...............................................................................................16 4.1.4 DEVIATION FROM TEST STANDARD .....................................................................16 4.1.5 TEST SETUP.............................................................................................................17 4.1.6 EUT OPERATING CONDITIONS ..............................................................................17 4.1.7 TEST RESULTS ........................................................................................................18 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................31 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................................31 4.2.2 TEST INSTRUMENTS...............................................................................................31 4.2.3 TEST PROCEDURES ...............................................................................................32 4.2.4 DEVIATION FROM TEST STANDARD .....................................................................32 4.2.5 TEST SETUP.............................................................................................................33 4.2.6 EUT OPERATING CONDITIONS ..............................................................................33 4.2.7 TEST RESULTS ........................................................................................................34 4.3 6dB BANDWIDTH MEASUREMENT.........................................................................36 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT .....................................................36 4.3.2 TEST SETUP.............................................................................................................36 4.3.3 TEST INSTRUMENTS...............................................................................................36 4.3.4 TEST PROCEDURE..................................................................................................36 4.3.5 DEVIATION FROM TEST STANDARD .....................................................................36 4.3.6 EUT OPERATING CONDITIONS ..............................................................................36 4.3.7 TEST RESULTS ........................................................................................................37 4.4 CONDUCTED OUTPUT POWER .............................................................................38 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ..............................38 4.4.2 TEST SETUP.............................................................................................................38 4.4.3 TEST INSTRUMENTS...............................................................................................38 4.4.4 TEST PROCEDURES ...............................................................................................38 Report No.: RF111031C30 3 Report Format Version 4.1.0 4.4.5 DEVIATION FROM TEST STANDARD .....................................................................38 4.4.6 EUT OPERATING CONDITIONS ..............................................................................38 4.4.7 TEST RESULTS ..................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST 1 PHOTOGRAPHS OF THE TEST CONFIGURATION (SAR Test Set Up Photos) Rear Face (0 cm Gap) Secondary Landscape (0 cm Gap) 2 Antenna Location Secondary Landscape Primary Landscape Secondary Portrait Primary Portrait WLAN Antenna 170 mm 65 mm 170 mm