H8N-WLL6190D25802.11g / 802.11n WLAN PCI-E Mini Card

Introduction: Askey WLL6190D25 802.11g / 802.11n WLAN PCI-E Mini Card User's Guide Before you begin Things you should know WLL6190D25 network Before you begin Obtain the following information from your network administrator (if you are a home user, obtain this information from the person that installed your wireless access point): l Network names (SSID) of the specific wireless networks that you want to connect to. l WEP (Wired Equivalent Privacy) key information (if any) for the networks you want to connect to. l For Microsoft® Windows® networking, your customer name and workgroup name. l For your network account, your user name and password. l Your IP address (if not using a DHCP server) Things you should know When you start your computer, your Askey WLL6190D25 802.11g / 802.11n WLAN PCI-E Mini Card detects certain wireless networks that are information you obtained from your network administrator. WEP is a security protocol for wireless local area networks (defined in the IEEE 802.11g standard) that encrypts data sent over radio waves. The use of the WEP key is optional and can be enabled or disabled. If the network you are connecting to has enabled WEP, you must also enable WEP in the network profile and set the WEP key to match the WEP key used by the network. Otherwise, you cannot connect to the network. Askey WLL6190D25 network Askey 802.11g / 802.11n WLAN PCI-E Mini Card (Model name : WLL6190D25) using Broadcom Wireless Utility to connect network. The Askey WLL6190D25 solution allows you to make a wireless connection to a network, as illustrated below. within range. Before you can connect to these and other wireless networks, you must configure a profile for each network using the Back to top Using the Broadcom Wireless Utility: Broadcom AirForce™ 54g™ and Intensi-fi™ Wireless Network Adapter User Guide Back to Contents Page Using the Broadcom Wireless Utility: Broadcom AirForce™ 54g™ and Intensi-fi™ Wireless Network Adapter User Guide Overview Utility Components Overview The Broadcom Wireless Utility enables you to do the following network tasks: l Manage your wireless networks and create network connection profiles (Wireless Networks tab) l Connect to available networks (utility icon in notification area) l Get information about the network status and signal and noise of your network connection (Link Status tab) l View current and accumulated statistics (Statistics tab) l Find out which broadcasting networks are in range and search for nonbroadcasting networks (Site Monitor tab) l Run tests on the wireless network adapter (Diagnostics tab) l Get date and version information about the utility, and software, hardware, and location details about your wireless network adapter ( Information tab) l Manually add or delete trusted servers and enable the manual acceptance or rejection of auto- provisioning and A-ID group changes ( Wireless Networks tab) l Manually import EAP-FAST PACs (Wireless Networks tab) In the utility, you can open Wireless Network Wizard to connect to a basic network or create an ad hoc network, or you can open the Wireless Network Connection Settings tool to connect to an advanced network. To do any of the other tasks, click the tab that is associated with the described task. To start using the utility, right-click the utility icon in the notification area, and then click Open Utility. If the icon is not available, open Broadcom Wireless Utility in Control Panel. NOTE: The utility icon may not appear exactly as shown here. See " Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon." Utility Components Utility components include the utility icon in the notification area, the six utility tabs, and Wireless Network Connection Settings. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (1 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce™ 54g™ and Intensi-fi™ Wireless Network Adapter User Guide Utility Icon To do any of the following tasks or operations, right-click the utility icon, and then click the appropriate item. l Open the on-line Broadcom AirForce™ 54g™ and Intensi-fi™ Wireless Network Adapter User Guide (Help Files) l Open About WLAN Card Utility to view links to Broadcom and Broadcom Customer Support websites and to view the version and date of the utility (About) l Hide the utility icon (Hide Tray Icon) l Disable or enable the radio (Disable/Enable Radio) l Connect to any of the networks for which you have created a connection profile and are within range (Connect To) l Open the utility to the Wireless Networks tab (Open Utility) l Open the utility to the Link Status tab to view information about the connection (Status) l Display a log of your wireless network events (Display Log) Wireless Networks Tab The Wireless Networks tab has tools that enable you to do the following: l Use the utility to manage your wireless networks l Add a network connection profile l Edit or remove a network connection profile l Change the order in which profiles are listed under Preferred network connections l Connect to any listed network without changing its order in the list l Disable or enable the radio (Disable/Enable Radio) l Show or hide the utility icon in the notification area l Choose which type of network to access l Lock or unlock a preferred network connection profile l Save your wireless network connection profiles as a WPN file l Import a WPN file l Manually add or delete trusted servers and enable the manual acceptance or rejection of auto- provisioning and A-ID group changes l Manually import EAP-FAST PACS On the Add menu, you can use either the wireless network wizard that is available from Broadcom Wireless Utility (see Connecting to a Basic Network or Creating an Ad Hoc Network Using the Wireless Network Wizard") or the utility (see "Connecting to an Advanced Network Using the Broadcom Wireless Utility") to add a network connection profile. To use the utility to manage your wireless networks, s…

Text truncated - open the document above for the full version.

FCC ID: H8N-WLL6190D25 Report No.: RF111003E03 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch November 17, 2011 Dear Application Examiner, ASKEY COMPUTER CORP, It’s a 802.11g / 802.11n WLAN PCI-E Mini Card FCC ID: H8N-WLL6190D25, would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip BCM43225. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is BCM43225. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via test tool. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: H8N-WLL6190D25 Report No.: RF111003E03 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Report No.: 111003E03 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 111003E03 Page 2 Report No.: 111003E03 Page 3 Report No.: 111003E03 Page 4 Report No.: 111003E03 Page 5 Report No.: 111003E03 Page 6

WLL6190 Label drawing and Location Label size : 14 * 6mm Label location (pasted on shield cover as below area) Model: WLL6190 FCC ID: H8N-WLL6190 IC: 1353A-WLL6190 Model: WLL6190 FCC ID: H8N-WLL6190 IC: 1353A-WLL6190 D25 D25 D25 D25 D25 D25

Report No.: 111003E03 Page 1 CONSTRUCTION PHOTOS OF EUT

FCC ID: H8N-WLL6190D25 Report No.: RF111003E03 Operational Description This device is an 802.11g / 802.11n WLAN PCI-E Mini Card, which operates in the 2.4GHz band; the maximum data rate could be up to 270Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 270Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by the 3.3Vdc from host equipment. The antennas are dipole and PIFA antennas with IPEX antenna connectors. The other instruction, please have a look at the users manual.

Report No.: SA111003E03 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA111003E03 MODEL NO.: WLL6190-D25 FCC ID: H8N-WLL6190D25 RECEIVED: Oct. 03, 2011 TESTED: Oct. 29, 2011 ISSUED: Nov. 10, 2011 APPLICANT: ASKEY COMPUTER CORP. ADDRESS: 10F, No.119, ChienKang RD., Chungho, Taipei, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA111003E03 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD....................................................................................3 1. CERTIFICATION..............................................................................................4 2. RF EXPOSURE LIMIT.....................................................................................5 3. MPE CALCULATION FORMULA.....................................................................5 4. CLASSIFICATION............................................................................................5 5. ANTENNA GAIN..............................................................................................6 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER...................6 Report No.: SA111003E03 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA111003E03 Original release Nov. 10, 2011 Report No.: SA111003E03 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT: 802.11g / 802.11n WLAN PCI-E Mini Card MODEL: WLL6190-D25 BRAND: Askey APPLICANT: ASKEY COMPUTER CORP. TEST SAMPLE: R&D SAMPLE TESTED: Oct. 29, 2011 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: WLL6190-D25) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Nov. 10, 2011 (Elsie Hsu, Specialist) APPROVED BY : , DATE: Nov. 10, 2011 (May Chen, Deputy Manager ) Report No.: SA111003E03 Report Format Version 4.0.0 5 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA111003E03 Report Format Version 4.0.0 6 5. ANTENNA GAIN There are two antennas provided to this EUT, please refer to the following table: Transmitter Circuit Brand Antenna Gain (dBi) (Include cable loss) Connector Cable length (cm) Antenna Type Chain (0) KINSUN 2 19 Dipole Chain (1) NA 2 IPEX 6.7 PIFA 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 21.0 2 20 0.039 1.00 --- END ---

Report No.: RF111003E03 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO.: RF111003E03 MODEL NO.: WLL6190-D25 FCC ID: H8N-WLL6190D25 RECEIVED: Oct. 03, 2011 TESTED: Oct. 29 to Nov. 03, 2011 ISSUED: Nov. 10, 2011 APPLICANT: ASKEY COMPUTER CORP. ADDRESS: 10F, No.119, ChienKang RD., Chungho, Taipei, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 77 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF111003E03 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD..............................................................................4 1. CERTIFICATION...........................................................................................5 2. SUMMARY OF TEST RESULTS...................................................................6 2.1 MEASUREMENT UNCERTAINTY................................................................7 3. GENERAL INFORMATION...........................................................................8 3.1 GENERAL DESCRIPTION OF EUT..............................................................8 3.2 DESCRIPTION OF TEST MODES..............................................................10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL..............11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.............................14 3.4 DESCRIPTION OF SUPPORT UNITS........................................................15 3.5 CONFIGURATION OF SYSTEM UNDER TEST.........................................15 4. TEST TYPES AND RESULTS.....................................................................16 4.1 CONDUCTED EMISSION MEASUREMENT..............................................16 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................16 4.1.2 TEST INSTRUMENTS................................................................................16 4.1.3 TEST PROCEDURES.................................................................................17 4.1.4 DEVIATION FROM TEST STANDARD.......................................................17 4.1.5 TEST SETUP..............................................................................................18 4.1.6 EUT OPERATING CONDITIONS................................................................18 4.1.7 TEST RESULTS..........................................................................................19 4.2 RADIATED EMISSION MEASUREMENT...................................................21 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.................................21 4.2.2 TEST INSTRUMENTS................................................................................22 4.2.3 TEST PROCEDURES.................................................................................23 4.2.4 DEVIATION FROM TEST STANDARD.......................................................23 4.2.5 TEST SETUP..............................................................................................24 4.2.6 EUT OPERATING CONDITIONS................................................................24 4.2.7 TEST RESULTS..........................................................................................25 4.3 6dB BANDWIDTH MEASUREMENT..........................................................54 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................54 4.3.2 TEST INSTRUMENTS................................................................................54 4.3.3 TEST PROCEDURE...................................................................................54 4.3.4 DEVIATION FROM TEST STANDARD.......................................................54 4.3.5 TEST SETUP..............................................................................................54 4.3.6 EUT OPERATING CONDITIONS................................................................54 4.3.7 TEST RESULTS..........................................................................................55 4.4 MAXIMUM PEAK OUTPUT POWER..........................................................59 Report No.: RF111003E03 3 Report Format Version 4.0.0 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........59 4.4.2 INSTRUMENTS..........................................................................................59 4.4.3 TEST PROCEDURES.................................................................................59 4.4.4 DEVIATION FROM TEST STANDARD.......................................................59 4.4.5 TEST SETUP..............................................................................................59 4.4.6 EUT OPERATING CONDITIONS................................................................59 4.4.7 TEST RESULTS..........................................................................................60 4.5 POWER SPECTRAL DENSITY MEASUREMENT......................................61 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT...................61 4.5.2 TEST INSTRUMENTS................................................................................61 4.5.3 TEST PROCEDURE...................................................................................61 4.5.4 DEVIATION FROM TEST STANDARD.......................................................61 4.5.5 TE…

Text truncated - open the document above for the full version.

Report No.: 111003E03 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 111003E03 2 RADIATED EMISSION TEST Report No.: 111003E03 3