H8N-WLU5054Wireless LAN module

WLU5054(RoHS) H/W SPECIFICATIONS Host Interfaces USB 2.0 compliant Form factor USB module Chipset Broadcom BCM43236B Operation Voltage 5V+/-10% Network Standards IEEE 802.11a/b/g/n Modulation Techniques DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM, MIMO Data Rate and features Data rates of up to 54 Mbps for 802.11a/g and 144.4 for 802.11n HT20, 300 Mbps for HT40 Network Architectures Infrastructure Operating Frequencies EEE 802.11b/g/n: 2412 GHz ~ 2462 GHz EEE 802.11a/n: 5180 - 5825GHz Operating Channels 802.11b: 11ch for North America, 13ch for Europe (ETSI),13ch for Japan(ch14 for Japan is optional) 802.11g: 11ch for North America, 13ch for Europe (ETSI) 802.11n: 3ch ~ 9ch ( HT40 ) for North America, 3ch ~11ch ( HT40 ) for Europe (ETSI) and Japan 802.11a/n: 5.180G~5.850G RF Output Power 2.4G: 802.11b: 22~23 dBm, output power 802.11g: 25~26 dBm, output power 802.11n:(HT20/HT40) : 25~29dBm 5G: 802.11a: 22~24dBm, output power 802.11n:(HT20/HT40) : 25~26dBm UNII Band: IEEE 802.11a CH36 - CH48 CH52 - CH64 CH100 – CH140 16~19dBm IEEE802.11an HT20 CH36 - CH48 CH52 - CH64 CH100 – CH140 16~19dBm IEEE802.11anHT40 CH38 - CH46 CH54 - CH62 CH102 – CH134 16~19dBm Receiver sensitivity (PER <10%) Legacy 6Mbps: -82dBm MCS 7 HT20: < -64dBm, MCS15 HT20: < -64dBm MCS 7 HT40: < -61dBm, MCS15 HT40: < -61dBm Antenna Type Printing Antenna RoHS compliant Yes Security Security support for WPS, WPA2, WPA, WAP and protected management frames Software Support WinXP, Win7 Temperatures Operates from 0 to 60 degree C Humidity (non-condensing) 15 to 95% non-condensing SETUP WLAN MODULE CONNECTION 1. Install driver in Windows, then you can link to AP Router 5_102_98_37_WinXP_mfgtest_Bcm_DriverOnly_BMac Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: H8N-WLU5054”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Askey Computer Corp. 10F. No. 119 Chienkang Rd Chung-Ho Taipei, Taiwan 23585 R.O.C Date: 2013-03-14 FCC ID: H8N-WLU5054 Declaration for DFS client devices We, Askey Computer Corp declare that the device does not support any non-US channels in all the operational mode(s), like Ad-Hoc...etc, for the following product. Also, the client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp. 10F. No. 119 Chienkang Rd Chung-Ho Taipei, Taiwan 23585 R.O.C Declaration for DFS client devices Date: 2013-03-14 FCC ID: H8N-WLU5054 Dear Examiner: Per KDB# 848637, We, Askey Computer Corp declare that following description truly represent our product in consideration. Please do not hesitate to contact us, if further info is required. Thanks. a). A channel/frequency plan for the device showing the channels that have active scanning or passive scanning. Active scanning is where the device can transmit a probe (beacon) and passive scanning is where the device can listen only without probes. Below is the channel / frequency plan for the device b). For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) or in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies), or modular devices that configure the modes of operations through software; the applicant must provide in the application software and operations description that discuss how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by an end user or an installer. Also, include an attestation that the device complies with the CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 Scan Type Active Active Active Active Active Active Active Active Active Active Active CH 36 40 44 48 52 56 60 64 Frequency (MHz) 5180 5200 5220 5240 5260 5280 5300 5320 Scan Type Active Active Active Active Passive Passive Passive Passive CH 100 104 108 112 116 132 136 140 Frequency (MHz) 5500 5520 5540 5560 5580 5660 5680 5700 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive CH 149 153 157 161 165 Frequency (MHz) 5745 5765 5785 5805 5825 Scan Type Active Active Active Active Active Askey Computer Corp. 10F. No. 119 Chienkang Rd Chung-Ho Taipei, Taiwan 23585 R.O.C requirements for software configuration control as discussed in KDB #594280. On DFS channels, the WLAN driver on the device operates under the control of an AP at all times, except when in ad-hoc mode, on US non-DFS channels. As described in the answer to question a, the device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is locked by proprietary password and cannot be changed or modified by end user. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-04-15 FCC ID: H8N-WLU5054 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to DA 04-1705 of the commission’s public notice, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp. 10F. No. 119 Chienkang Rd Chung-Ho Taipei, Taiwan 23585 R.O.C Date: 2013-03-14 FCC ID: H8N-WLU5054 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp. 10F. No. 119 Chienkang Rd Chung-Ho Taipei, Taiwan 23585 R.O.C Date: 2013-03-14 FCC ID: H8N-WLU5054 A U T H O R I Z A T I O N L E T T E R To whom it may concern: We, the undersigned Askey Computer Corp hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15C, 15E and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ----------------------------------- John Chiou Director Askey Computer Corp

FCC ID: H8N-WLU5054 Report No.: RF130308C12 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch April 15, 2013 Dear Application Examiner, Askey Computer Corp., Wireless LAN module, FCC ID: H8N-WLU5054 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip BCM43236B. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is BCM43236B. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: H8N-WLU5054 Report No.: RF130308C12 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

The label will be permanently affixed at a conspicuous location on the device. EUT Label location

FCC ID: H8N-WLU5054 ASKEY COMPUTER CORP. Model: WLU5054-D84 Wireless LAN module

Page 2

FCC ID: H8N-WLU5054 Report No.: RF130308C12 Operational Description This device is a Wireless LAN module, which operates in 2.4GHz & 5.0GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 5Vdc from host equipment. The antenna is Printed with U.FL-R antenna connectors. The other instruction, please have a look at the users manual.

Report No.: SA130308C12 1 of 6 Report Format Version 5.1.0 RF EXPOSURE REPORT REPORT NO.: SA130308C12 MODEL NO.: WLU5054-D84 FCC ID: H8N-WLU5054 RECEIVED: Mar. 08, 2013 TESTED: Mar. 13 ~ Mar. 15, 2013 ISSUED: Mar. 22, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA130308C12 2 of 6 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 3 1. CERTIFICATION ....................................................................................................................... 4 2. RF EXPOSURE ........................................................................................................................ 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) .................................................. 5 2.2 MPE CALCULATION FORMULA .............................................................................................. 5 2.3 CLASSIFICATION ..................................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................................... 6 Report No.: SA130308C12 3 of 6 Report Format Version 5.1.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130308C12 Original release Mar. 22, 2013 Report No.: SA130308C12 4 of 6 Report Format Version 5.1.0 1. CERTIFICATION PRODUCT: Wireless LAN module MODEL NO.: WLU5054-D84 BRAND: Askey APPLICANT: Askey Computer Corp TESTED: Mar. 13 ~ Mar. 15, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: WLU5054-D84) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Mar. 22, 2013 Ivy Lin / Specialist APPROVED BY: , DATE :Mar. 22, 2013 Ken Liu / Senior Manager Report No.: SA130308C12 5 of 6 Report Format Version 5.1.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130308C12 6 of 6 Report Format Version 5.1.0 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER Frequency band (MHz) Conducted power (dBm) Antenna Gain (dBi) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412~2462 28.33 5.33 0.462 1 5180~5240 16.99 6.28 0.042 1 5260~5320 18.31 6.60 0.062 1 5500~5700 18.11 6.69 0.060 1 5745~5825 25.89 6.39 0.336 1 Note: For 2.4GHz: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /N ANT ]= 5.33dBi For 5180~5240MHz: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /N ANT ]= 6.28dBi For 5260~5320MHz: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /N ANT ]= 6.60dBi For 5500~5700MHz: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /N ANT ]= 6.69dBi For 5745~5825MHz: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /N ANT ]= 6.39dBi

Report No.: RF130308C12-2 1 of 25 Report Format Version 5.0.0 DFS TEST REPORT REPORT NO.: RF130308C12-2 MODEL NO.: WLU5054-D84 FCC ID: H8N-WLU5054 RECEIVED: Mar. 08, 2013 TESTED: Mar. 22, 2013 ISSUED: Mar. 22, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130308C12-2 2 of 25 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 3 1. CERTIFICATION ....................................................................................................................... 4 3. EUT INFORMATION ................................................................................................................. 5 3.1 OPERATING FREQUENCY BANDS AND MODE OF EUT ...................................................... 5 3.2 EUT SOFTWARE AND FIRMWARE VERSION ....................................................................... 5 3.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT ..................................................... 5 3.4 EUT MAXIMUM CONDUCTED POWER .................................................................................. 6 3.5 EUT MAXIMUM E.I.R.P. POWER ............................................................................................. 7 3.6 TRANSMIT POWER CONTROL (TPC) .................................................................................... 8 3.7 STATEMENT OF MAUNFACTURER ........................................................................................ 8 4. U-NII DFS RULE REQUIREMENTS ......................................................................................... 9 4.1 WORKING MODES AND REQUIRED TEST ITEMS ................................................................ 9 4.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS ............................................................. 10 5. TEST & SUPPORT EQUIPMENT LIST .................................................................................. 12 5.1 TEST INSTRUMENTS ............................................................................................................ 12 5.2 DESCRIPTION OF SUPPORT UNITS ................................................................................... 12 6. TEST PROCEDURE ............................................................................................................... 13 6.1 ADT DFS MEASUREMENT SYSTEM .................................................................................... 13 6.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL: ................................................ 14 6.3 DEVIATION FROM TEST STANDARD ................................................................................... 15 6.4 CONDUCTED TEST SETUP CONFIGURATION ................................................................... 15 6.4.1 CLIENT WITHOUT RADAR DETECTION MODE .................................................................. 15 7. TEST RESULTS ...................................................................................................................... 16 7.1 SUMMARY OF TEST RESULTS ............................................................................................ 16 7.2 DETELED TEST RESULTS .................................................................................................... 17 7.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE. . 17 7.2.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME.................................. 18 7.2.3 NON-OCCUPANCY PERIOD ................................................................................................. 20 7.2.4 NON-ASSOCIATED TEST ...................................................................................................... 22 7.2.5 NON- CO-CHANNEL TEST .................................................................................................... 22 8. PHOTOGRAPHS OF THE TEST CONFIGURATION ............................................................. 23 9. INFORMATION ON THE TESTING LABORATORIES ........................................................... 24 10. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ..............................................…

Text truncated - open the document above for the full version.

Report No.: RF130308C12 1 of 83 Report Format Version 5.1.0 FCC TEST REPORT (15.247) REPORT NO.: RF130308C12 MODEL NO.: WLU5054-D84 FCC ID: H8N-WLU5054 RECEIVED: Mar. 08, 2013 TESTED: Mar. 13 ~ Mar. 15, 2013 ISSUED: Mar. 22, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130308C12 2 of 83 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 5 1. CERTIFICATION ....................................................................................................................... 6 2. SUMMARY OF TEST RESULTS .............................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ............................................................................................ 7 3. GENERAL INFORMATION ....................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ......................................................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................................... 11 3.3 DESCRIPTION OF SUPPORT UNITS ................................................................................... 15 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................................... 15 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................ 16 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ............................................................. 17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................................. 17 4.1.1 LIMITS OF RADIATED EMISSIO…

Text truncated - open the document above for the full version.