H8N-WLU5153Wireless Module

THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of this device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC and IC require this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. Wireless LAN adaptor has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. ENGLISH THE FOLLOWING APPLIES ONLY IN THE U.S.A. Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced host product technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: H8N-WLU5153”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. THE FOLLOWING APPLIES ONLY IN CANADA. This Class B digital apparatus complies with Canadian ICES-003. Product Identification Marking is located on the top of the Wireless Module. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this …

Text truncated - open the document above for the full version.

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-27 FCC ID: H8N-WLU5153 Declaration for DFS client devices We, Askey Computer Corp, declare that the device, FCC ID: H8N-WLU5153 Model Name: WLU5153-D81, does not have “Ad Hoc on non-US frequencies” and/or “on DFS frequencies. Also, the client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. Moreover, for 2.4G part of this device, only channels 1~11, will be used in North America and all non-US frequencies and Country code selection are disabled through proprietary software and is not user changeable. Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours, John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Declaration for DFS client devices Date: 2013-08-26 FCC ID: H8N-WLU5153 Dear Examiner: Per KDB# 848637, We, Askey Computer Corp declare that following description truly represent our product in consideration. Please do not hesitate to contact us, if further info is required. Thanks. a). A channel/frequency plan for the device showing the channels that have active scanning or passive scanning. Active scanning is where the device can transmit a probe (beacon) and passive scanning is where the device can listen only without probes. Below is the channel / frequency plan for the device b). For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) or in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies), or modular devices that configure the modes of operations through software; the applicant must provide in the application software and operations description that discuss how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by an end user or an installer. Also, include an attestation that the device complies with the requirements for software configuration control as discussed in KDB #594280. CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 Scan Type Active Active Active Active Active Active Active Active Active Active Active CH 36 40 44 48 52 56 60 64 Frequency (MHz) 5180 5200 5220 5240 5260 5280 5300 5320 Scan Type Active Active Active Active Passive Passive Passive Passive CH 100 104 108 112 116 132 136 140 Frequency (MHz) 5500 5520 5540 5560 5580 5660 5680 5700 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive CH 149 153 157 161 165 Frequency (MHz) 5745 5765 5785 5805 5825 Scan Type Active Active Active Active Active On DFS channels, the WLAN driver on the device operates under the control of an AP at all times, except when in ad-hoc mode, on US non-DFS channels. As described in the answer to question a, the device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is locked by proprietary password and cannot be changed or modified by end user. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-26 FCC ID: H8N-WLU5153 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to DA 04-1705 of the commission’s public notice, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-26 FCC ID: H8N-WLU5153 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- John Chiou Director Askey Computer Corp

Askey Computer Corp 10F, No. 119, Chienkang Rd Chung-Ho, Taipei 235, Taiwan TEL: +886-2-2228-7588 FAX: +886-2-3234-9211 Date: 2013-08-27 FCC ID: H8N-WLU5153 A U T H O R I Z A T I O N L E T T E R To whom it may concern: We, the undersigned Askey Computer Corp hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15 C & 15E and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, John Chiou Director Askey Computer Corp

FCC ID: H8N-WLU5153 Report No.: RF 130724C01 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch August 27, 2013 Dear Application Examiner, Askey Computer Corp., Wireless Module, FCC ID: H8N-WLU5153 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip AR9374. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is AR9374. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: H8N-WLU5153 Report No.: RF 130724C01 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

The label will be permanently affixed at a conspicuous location on the device. EUT Label location

Label

Page 2

FCC ID: H8N-WLU5153 Report No.: RF130724C01 Operational Description This device is a Wireless Module, which operates in 2.4GHz & 5.0GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 5Vdc from host equipment. The antenna is PCB without antenna connectors. The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA111011C17N 1 of 6 Report Format Version 5.0.0 Reference No.: 130724C01 RF EXPOSURE REPORT REPORT NO.: SA111011C17N MODEL NO.: WLU5153-D81 FCC ID: H8N-WLU5153 RECEIVED: Jul. 24, 2013 TESTED: Jul. 26 ~ Aug. 07, 2013 ISSUED: Aug. 14, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA111011C17N 2 of 6 Report Format Version 5.0.0 Reference No.: 130724C01 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 3 1. CERTIFICATION .......................................................................................................... 4 2. RF EXPOSURE ........................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ..................................... 5 2.2 MPE CALCULATION FORMULA................................................................................. 5 2.3 CLASSIFICATION ....................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .............................. 6 Report No.: SA111011C17N 3 of 6 Report Format Version 5.0.0 Reference No.: 130724C01 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA111011C17N Original release Aug. 14, 2013 Report No.: SA111011C17N 4 of 6 Report Format Version 5.0.0 Reference No.: 130724C01 1. CERTIFICATION PRODUCT: Wireless Module MODEL NO.: WLU5153-D81 BRAND: Panasonic APPLICANT: Askey Computer Corp TESTED: Jul. 26 ~ Aug. 07, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: WLU5153-D81) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Aug. 14, 2013 Ivy Lin / Specialist APPROVED BY: , DATE :Aug. 14, 2013 Ken Liu / Senior Manager Report No.: SA111011C17N 5 of 6 Report Format Version 5.0.0 Reference No.: 130724C01 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA111011C17N 6 of 6 Report Format Version 5.0.0 Reference No.: 130724C01 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER Frequency band (MHz) Conducted power (dBm) Antenna Gain (dBi) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412~2462 26.07 1.87 0.124 1 5180~5240 16.45 3.21 0.018 1 5260~5320 18.82 3.31 0.032 1 5500~5700 19.13 3.48 0.036 1 5745~5825 26.86 2.81 0.184 1 ---END---

Report No.: RF111011C17N-2 1 of 23 Report Format Version 5.0.0 Reference No.: 130724C01 DFS TEST REPORT REPORT NO.: RF111011C17N-2 MODEL NO.: WLU5153-D81 FCC ID: H8N-WLU5153 RECEIVED: Jul. 24, 2013 TESTED: Aug. 02 ~ Aug. 13, 2013 ISSUED: Aug. 20, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF111011C17N-2 2 of 23 Report Format Version 5.0.0 Reference No.: 130724C01 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................ 3 1. CERTIFICATION .......................................................................................................... 4 2. EUT INFORMATION .................................................................................................... 5 2.1 OPERATING FREQUENCY BANDS AND MODE OF EUT ......................................... 5 2.2 EUT SOFTWARE AND FIRMWARE VERSION ........................................................... 5 2.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT ........................................ 5 2.4 EUT MAXIMUM CONDUCTED POWER ..................................................................... 6 2.5 EUT MAXIMUM E.I.R.P. POWER ................................................................................ 7 2.6 TRANSMIT POWER CONTROL (TPC) ....................................................................... 8 2.7 STATEMENT OF MAUNFACTURER ........................................................................... 8 3. U-NII DFS RULE REQUIREMENTS ............................................................................ 9 3.1 WORKING MODES AND REQUIRED TEST ITEMS ................................................... 9 3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS ................................................ 10 4. TEST & SUPPORT EQUIPMENT LIST ..................................................................... 12 4.1 TEST INSTRUMENTS ............................................................................................... 12 4.2 DESCRIPTION OF SUPPORT UNITS ...................................................................... 12 5. TEST PROCEDURE .................................................................................................. 13 5.1 BV ADT DFS MEASUREMENT SYSTEM ................................................................. 13 5.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL: ................................... 14 5.3 DEVIATION FROM TEST STANDARD ...................................................................... 14 5.4 RADIATED TEST SETUP CONFIGURATION ........................................................... 15 5.4.1 CLIENT WITHOUT RADAR DETECTION MODE ..................................................... 15 6. TEST RESULTS ........................................................................................................ 16 6.1 SUMMARY OF TEST RESULTS ............................................................................... 16 6.2 TEST RESULTS ........................................................................................................ 17 6.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE. ....................................................................................................................... 17 6.2.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME ..................... 18 6.2.3 NON-OCCUPANCY PERIOD .................................................................................... 20 6.2.4 NON-ASSOCIATED TEST ......................................................................................... 22 6.2.5 NON- CO-CHANNEL TEST ....................................................................................... 22 7. INFORMATION ON THE TESTING LABORATORIES .............................................. 23 Report No.: RF111011C17N-2 3 of 23 Report Format Version 5.0.0 Reference No.: 130724C01 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF111011C17N-2 Original release Aug. 20, 2013 Report No.: RF111011C17N-2 4 of 23 Report Format Version 5.0.0 Reference No.: 130724C01 1. CERTIFICATION PRODUCT: Wireless Module MODEL NO.: WLU5153-D81 BRAND: Panasonic APPLICANT: Askey Computer Corp TESTED: Aug. 02 ~ Aug. 13, 2013 TEST SAMPLE: E…

Text truncated - open the document above for the full version.

Report No.: RF111011C17N 1 of 87 Report Format Version 5.2.0 Reference No.: 130724C01 FCC TEST REPORT (15.247) REPORT NO.: RF111011C17N MODEL NO.: WLU5153-D81 FCC ID: H8N-WLU5153 RECEIVED: Jul. 24, 2013 TESTED: Jul. 26 ~ Aug. 07, 2013 ISSUED: Aug. 14, 2013 APPLICANT: Askey Computer Corp ADDRESS: 10F, No. 119, Chienkang Rd Chung-Ho Taipei Taiwan 235 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF111011C17N 2 of 87 Report Format Version 5.2.0 Reference No.: 130724C01 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 5 1. CERTIFICATION .......................................................................................................... 6 2. SUMMARY OF TEST RESULTS ................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ............................................…

Text truncated - open the document above for the full version.