H8NPKE938Cable Modem

User manual DWG875/DWG875T - Wireless Voice Gateway Illustrations contained in this document are for representation only. i CAUTION Disconnect power before servicing. This device is intended for indoor operation only. Telephone jacks Line 1 and Line 2 must not be connected to outside wiring. CAUTION To ensure reliable operation and to prevent overheating, provide adequate ventilation for this modem and keep it away from heat sources. Do not locate near heat registers or other heat-producing equipment. Provide for free air flow around the Wireless Voice Gateway and its power supply. This symbol means that your inoperative electronic appliance must be collected separately and not mixed with the household waste. The European Union has implemented a specific collection and recycling system for which producers' are responsible. This appliance has been designed and manufactured with high quality materials and components that can be recycled and reused. Electrical and electronic appliances are liable to contain parts that are necessary in order for the system to work properly but which can become a health and environmental hazard if they are not handled or disposed of in the proper way. Consequently, please do not throw out your inoperative appliance with the household waste. If you are the owner of the appliance, you must deposit it at the appropriate local collection point or leave it with the vendor when buying a new appliance. - If you are a professional user, please follow your supplier's instructions. - If the appliance is rented to you or left in your care, please contact your service provider. Help us protect the environment in which we live ! This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device mat not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Illustrations contained in this document are for representation only. ii Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Illustrations contained in this document are for representation only. iii NORTH AMERICAN CABLE INSTALLER: This reminder is provided to call your attention to Article 820.93 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. PacketCable and DOCSIS compliant The Thomson DWG875/DWG875T is a voice-capable cable modem, which provides broadband Internet access and telephone capability all in one unit! Also referred to as an Embedded Media Terminal Adapter (EMTA), this cable modem connects to cable systems using DOCSIS and PacketCable standards. (Check with your cable operator for compatibility.) The Thomson DWG875/DWG875T offers a high-speed connection to the Internet using an Ethernet connection. If you have subscribed to telephone service from your cable operator, you will be able to place regular phone calls using your home phone(s) and/or fax machine. The Thomson DWG875/DWG875T provides two RJ-11 connectors for your phone or home phone system, allowing one or two line service. Operating Information Operating Temperature: 0 ̊ to 40 ̊ C (32 ̊ to 104 ̊ F) Storage Temperature: -40 ̊ to 70 ̊ C (-40° to 158° F) Humidity: 5% ~ 95% non-condensing If you purchased this product at a retail outlet, please read the following: Product Information Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. The numbers are located on the bottom of the product. Model No. ____________________________Serial No ________________________________ Purchase Date: ________________________Dealer/Address/Phone: _________________________ Table of Contents Illustrations contained in this document are for representation only. 1 Chapter 1: Connections and Setup ........................................................................................... 5 Introduction ...........…

Text truncated - open the document above for the full version.

Chapter 2: WEB Configuration Illustrations contained in this document are for representation only. 46 8. RIP (Routing Information Protocol) Setup This feature enables the gateway to be used in small business situations where more than one LAN (local area network) is installed. The RIP protocol provides the gateway a means to “advertise” available IP routes to these LANs to your cable operator, so packets can be routed properly in this situation. Your cable operator will advise you during installation if any setting changes are required here. Fig. 26 Gateway\Advanced\RIP Setup Chapter 2: WEB Configuration Illustrations contained in this document are for representation only. 47 Gateway – Firewall Web Page Group 1. Web Content Filtering These pages allow you to enable, disable, and configure a variety of firewall features associated with web browsing, which uses the HTTP protocol and transports HTML web pages. On these pages, you designate the gateway packet types you want to have forwarded or blocked. You can activate settings by checking them and clicking Apply. The web-related filtering features you can activate from the Web Content Filter page include Filter Proxy, Filter Cookies, Filter Java Applets, Filter ActiveX, Filter Popup Windows, and Firewall Protection. If you want the gateway to exclude your selected filters to certain computers on your LAN, enter their MAC addresses in the Trusted Computers area of this page. Fig. 27 Gateway\Firewall\Web Filter Chapter 2: WEB Configuration Illustrations contained in this document are for representation only. 48 2. TOD Filtering Use this page to set rules that will block specific LAN side PCs from accessing the Internet, but only at specific days and times. Specify a PC by its hardware MAC address, and then use the tools to specify blocking time. Finally, click the Apply button to save your settings. Fig. 28 Gateway\Firewall\TOD Filtering Chapter 2: WEB Configuration Illustrations contained in this document are for representation only. 49 3. Local Log and Remote Log The gateway builds a log of firewall blocking actions that Firewall has taken.Using the Local Log page lets you specify an email address to which you want the gateway to email this log. You must also tell the gateway your outgoing (i.e. SMTP) email server’s name, so it can direct the email to it. Enable Email Alerts has the gateway forward email notices when Firewall protection events occur. Click E-mail Log to immediately send the email log. Click Clear Log to clear the table of entries for a fresh start. The log of these events is also visible on the screen. For each blocking event type that has taken place since the table was last cleared, the table shows Description, Count, Last Occurrence, Target, and Source. Fig. 29 Gateway\Firewall\Local Log The Remote Log page allows you to specify the IP address where a SysLog server is located and select different types of firewall events that may occur. Then, each time such an event occurs, notification is automatically sent to this log server. Fig. 30 Gateway\Firewall\Remote Log Chapter 2: WEB Configuration Illustrations contained in this document are for representation only. 50 Gateway – Parental Control Web Page Group 1. Basic This page allows you to enable, disable, and configure a variety of firewall features associated with web browsing, which uses the HTTP protocol and transports HTML web pages. On these pages, you designate the gateway packet types you want to have forwarded or blocked. You can activate settings by checking them and clicking Apply. Here are some of your choices on the Parental Control page:  Activate Keyword Blocking and specify some keywords in the Keyword List to cause blocking of web pages on the WAN side with the specified keyword in the content.  Activate Domain Blocking and specify some Domain Names (e.g. disney.com) in the Domain List. Fig. 31 Gateway\Parental Control\Basic Chapter 2: WEB Configuration Illustrations contained in this document are for representation only. 51 Gateway – Wireless Web Page Group The Wireless web pages group enables a variety of settings that can provide secure and reliable wireless communications for even the most demanding tech-savvy user. The Wireless Voice Gateway offers a choice of 802.1x, WPA and WPA-PSK authentication of your PCs to the gateway, 64 and 128 bit WEP encryption of communication between the gateway and your PCs to guaranty security, and an Access Control List function that enables you to restrict wireless access to only your specific PCs. The wireless function will probably work in your home as shipped from the factory, but without the security features activated. In addition, the factory default wireless channel setting may not provide optimum changes are recommended from the factory defaults, to secure your wireless communications and provide optimum performance. Performance Because your wireless communication travels through the air, the factory default wireless channel setting may not provide optimum performance in your home if you or your neighbors have other interfering 2.4GHz devices such as cordless phones. If your wireless PC is experiencing very sluggish or dramatically slower communication compared with the speed you achieve on your PC that is wired to the gateway, try changing the channel number. See the 802.11b/g/n Basic Web Page discussion below for details. Authentication Authentication enables you to restrict your gateway from communicating with any remote wireless PCs that aren’t yours. The following minimum authentication-related changes to factory defaults are recommended. See the 802.11b/g Basic and Access Control Web Page discussions below for details. Network Name (SSID) – Set a unique name you choose Network Type – Set to Open Access Control List – Enter your wireless PCs’ MAC addresses Security Security secures or scrambles messages traveling through the air between your wireless PCs and the gateway, so they can’t be observed by oth…

Text truncated - open the document above for the full version.

ASKEY COMPUTER CORP. 7F, No.22, TAI YUEN ST., CHUPEI, HSINCHU, TAIWAN 302, R.O.C. Date : June 24, 2010 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: H8NPKE938 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------------------ John Chiou Director ASKEY COMPUTER CORP. TEL: + 886 (2) 2228-7588 #18726 E-mail : [email protected]

ASKEY COMPUTER CORP. 7F, No.22, TAI YUEN ST., CHUPEI, HSINCHU, TAIWAN 302, R.O.C. Date: 24 June, 2010 GENERAL DECLARATION We, ASKEY COMPUTER CORP. declares that device does not have “Ad Hoc on non-US frequencies” and/or “on DFS frequencies” while applying for the follow product. The client software and associated drivers will not initiate any transmission on DFS frequencies. This includes transmissions for beacon ad-hoc peer-to-peer modes. FCC ID: H8NPKE938 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, --------------------------------- John Chiou Director ASKEY COMPUTER CORP. TEL: + 886 (2) 2228-7588 #18726 E-mail : [email protected]

ASKEY COMPUTER CORP. 7F, No.22, TAI YUEN ST., CHUPEI, HSINCHU, TAIWAN 302, R.O.C. Power of Attorney Date : 24 June, 2010 To whom it may concern: We, the undersigned ASKEY COMPUTER CORP. hereby authorize Bureau Veritas Consumer Product Service (Hong Kong) Limited, Taoyuan Branch of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C+E approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. This authorization is limited to the following products： FCC ID : H8NPKE938 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, --------------------------------- John Chiou Director ASKEY COMPUTER CORP. TEL: + 886 (2) 2228-7588 #18726 E-mail : [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Battery

(Fig.1) FCC ID: H8NPKE938 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Back Side - LABEL

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Internal power supply: AMS56-1502400F Page 9 Internal power supply: SU36-2150240-I3

Report No.: SA990614E03 Report Format Version 3.0.1 1 RF EXPOSURE REPORT REPORT NO.: SA990614E03 MODEL NO.: DWG875T, DWG875XX (The “X” of Model Name could be A~Z) FCC ID: H8NPKE938 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: ASKEY COMPUTER CORP. ADDRESS: 10F, No.119, ChienKang RD., Chungho, Taipei, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan Report No.: SA990614E03 Report Format Version 3.0.1 2 RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in our lab, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Report No.: SA990614E03 Report Format Version 3.0.1 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm 2 . If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device Report No.: SA990614E03 Report Format Version 3.0.1 4 6. TEST RESULTS 6.1 Antenna Gain There are two antennas provided to this EUT, please refer to the following table: No. Antenna Type Antenna Connector Antenna Gain (dBi) Cable loss(dB) Net Gain (dBi) Cable Length (mm) Frequency range (GHz) 1 PIFA I-PEX 2.45 0.45 2 150 1~6 2 PIFA I-PEX 2.56 0.56 2 200 1~6 Report No.: SA990614E03 Report Format Version 3.0.1 5 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: For 15.247(2.4GHz): 802.11b: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 218.8 0.069 1.0 6 2437 213.8 0.067 1.0 11 2462 195.0 0.061 1.0 802.11g: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 190.5 0.060 1.0 6 2437 346.7 0.109 1.0 11 2462 131.8 0.042 1.0 802.11n (20MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 310.1 0.098 1.0 6 2437 647.4 0.204 1.0 11 2462 346.3 0.109 1.0 802.11n (40MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2422 275.6 0.087 1.0 4 2437 302.2 0.095 1.0 7 2452 382.4 0.121 1.0 Report No.: SA990614E03 Report Format Version 3.0.1 6 For 15.247(5GHz): 802.11a: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 149 5745 218.8 0.069 1.0 157 5785 218.8 0.069 1.0 165 5825 223.9 0.071 1.0 802.11n (20MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 149 5745 414.4 0.131 1.0 157 5785 458.2 0.144 1.0 165 5825 432.8 0.136 1.0 802.11n (40MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 151 5755 343.6 0.108 1.0 159 5795 418.0 0.132 1.0 Report No.: SA990614E03 Report Format Version 3.0.1 7 For 15.407(5GHz): 802.11a: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 36 5180 22.4 0.007 1.0 40 5200 24.5 0.008 1.0 48 5240 22.9 0.007 1.0 802.11n (20MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 36 5180 23.1 0.007 1.0 40 5200 21.7 0.007 1.0 48 5240 21.7 0.007 1.0 802.11n (40MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 38 5190 15.7 0.005 1.0 46 5230 26.1 0.008 1.0 --- END ---

Report No.: RF990614E03 1 Report Format Version 3.0.1 FCC TEST REPORT (15.247) REPORT NO.: RF990614E03 MODEL NO.: DWG875T, DWG875XX (The “X” of Model Name could be A~Z) FCC ID: H8NPKE938 RECEIVED: June 14, 2010 TESTED: June 15 to July 14, 2010 ISSUED: July 23, 2010 APPLICANT: ASKEY COMPUTER CORP. ADDRESS: 10F, No.119, ChienKang RD., Chungho, Taipei, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 124 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by any government agencies. The test results in the report only apply to the tested sample. Report No.: RF990614E03 2 Report Format Version 3.0.1 Table of Contents 1. CERTIFICATION...........................................................................................5 2. SUMMARY OF TEST RESULTS...................................................................6 2.1 MEASUREMENT UNCERTAINTY................................................................8 3. GENERAL INFORMATION...........................................................................9 3.1 GENERAL DESCRIPTION OF EUT..............................................................9 3.2 DESCRIPTION OF TEST MODES..............................................................13 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL..............14 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.............................17 3.4 DESCRIPTION OF SUPPORT UNITS........................................................18 3.5 CONFIGURATION OF SYSTEM UNDER TEST.........................................19 4. TEST TYPES AND RESULTS (802.11b & g, 2400 ~ 2483.5MHz Band).....20 4.1 CONDUCTED EMISSION MEASUREMENT..............................................20 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................20 4.1.2 TEST INSTRUMENTS................................................................................20 4.1.3 TEST PROCEDURES.................................................................................21 4.1.4 DEVIATION FROM TEST STANDARD.......................................................21 4.1.5 TEST SETUP..............................................................................................22 4.1.6 EUT OPERATING CONDITIONS................................................................22 4.1.7 TEST RESULTS..........................................................................................23 4.2 RADIATED EMISSION MEASUREMENT...................................................27 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.................................27 4.2.2 TEST INSTRUMENTS................................................................................28 4.2.3 TEST PROCEDURES.................................................................................30 4.2.4 DEVIATION FROM TEST STANDARD.......................................................30 4.2.5 TEST SETUP..............................................................................................31 4.2.6 EUT OPERATING CONDITIONS................................................................32 4.2.7 TEST RESULTS..........................................................................................33 4.3 6dB BANDWIDTH MEASUREMENT..........................................................62 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................62 4.3.2 TEST INSTRUMENTS................................................................................62 4.3.3 TEST PROCEDURE...................................................................................62 4.3.4 DEVIATION FROM TEST STANDARD.......................................................62 4.3.5 TEST SETUP..............................................................................................62 4.3.6 EUT OPERATING CONDITIONS................................................................62 4.3.7 TEST RESULTS..........................................................................................63 4.4 MAXIMUM PEAK OUTPUT POWER..........................................................67 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........67 Report No.: RF990614E03 3 Report Format Version 3.0.1 4.4.2 INSTRUMENTS..........................................................................................67 4.4.3 TEST PROCEDURES.................................................................................67 4.4.4 DEVIATION FROM TEST STANDARD.......................................................67 4.4.5 TEST SETUP..............................................................................................67 4.4.6 EUT OPERATING CONDITIONS................................................................67 4.4.7 TEST RESULTS..........................................................................................68 4.5 POWER SPECTRAL DENSITY MEASUREMENT......................................70 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT...................70 4.5.2 TEST INSTRUMENTS................................................................................70 4.5.3 TEST PROCEDURE...................................................................................70 4.5.4 DEVIATION FROM TEST STANDARD.......................................................70 4.5.5 TEST SETUP..............................................................................................70 4.5.6 EUT OP…

Text truncated - open the document above for the full version.

Report No.: RF990614E03-1 1 Report Format Version 3.0.1 FCC TEST REPORT (15.407) REPORT NO.: RF990614E03-1 MODEL NO.: DWG875T, DWG875XX (The “X” of Model Name could be A~Z) FCC ID: H8NPKE938 RECEIVED: June 14, 2010 TESTED: June 15 to July 14, 2010 ISSUED: July 23, 2010 APPLICANT: ASKEY COMPUTER CORP. ADDRESS: 10F, No.119, ChienKang RD., Chungho, Taipei, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 80 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by any government agencies. The test results in the report only apply to the tested sample. Report No.: RF990614E03-1 2 Report Format Version 3.0.1 Table of Contents 1. CERTIFICATION....................................................................................................4 2. SUMMARY OF TEST RESULTS............................................................................5 2.1 MEASUREMENT UNCERTAINTY..........................................................................6 3. GENERAL INFORMATION.....................................................................................7 3.1 GENERAL DESCRIPTION OF EUT.......................................................................7 3.2 DESCRIPTION OF TEST MODES.......................................................................11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:.......................12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................15 3.4 DESCRIPTION OF SUPPORT UNITS..................................................................16 3.5 CONFIGURATION OF SYSTEM UNDER TEST...................................................17 4. TEST TYPES AND RESULTS..............................................................................18 4.1 CONDUCTED EMISSION MEASUREMENT........................................................18 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT......................................18 4.1.2 TEST INSTRUMENTS..........................................................................................18 4.1.3 TEST PROCEDURES..........................................................................................19 4.1.4 DEVIATION FROM TEST STANDARD.................................................................19 4.1.5 TEST SETUP.......................................................................................................20 4.1.6 EUT OPERATING CONDITIONS.........................................................................20 4.1.7 TEST RESULTS…

Text truncated - open the document above for the full version.