HBOFLOATWIRELESS SPEAKER

Fold Fold Fold Fold 994080 Merrimack, New Hampshire, USA 03054 800-846-3000 • Brookstone.com Fold Fold Fold Floating Speaker XXXXXXXX TBD FINAL NAME AND PHOTO FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the distance between accept any interference received, including interference that may cause undesired operation. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This equipment may not cause harmful interference. 2. This equipment must accept any interference received, including interference that may cause undesired operation. Modifications not authorized by the manufacturer may void the user’s authority to operate this device. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. Use only the supplied antenna. FCC ID: HBOFLOAT SPECIFICATIONS Power Supply: DC 5V/ 1A (Input) Range: Class 2, up to 33 ft (10 m) Compatibility: Bluetooth 2.0 or above device with A2DP/AVRCP Speaker: 4 Ohm 1.25" (2) Power Output: 2W*2 Frequency Response: 90Hz ~ 20KHz Battery Life: Approx. 8 hours Charging Time: Approx. 3 hours Product Weight: Approx. .6lbs Product Dimensions: Approx. 5.8" (dia) x 1.4" (h) The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Brookstone is under license. © Brookstone 2015 CARE AND MAINTENANCE To clean, wipe the speaker with a soft, dry cloth. Important: Although the speaker is waterproof, avoid submerging the speaker for long periods of time as damage may occur. Note: The speaker remembers the last device paired. If you would like to use another device, pair that device manually. TROUBLESHOOTING BLUETOOTH ® DISCONNECTION • Ensure your device is within 33 feet of the speaker and reconnect your device to “Brookstone Floating.” AUDIO IS NOT CLEAR • Power the speaker off and then back on. • Adjust your device’s equalizer. • Check the volume level on the speaker. • Check the volume level on your device. SPEAKER DOES NOT PLAY AUDIO • Make sure the speaker is charged. • Power the speaker off and then back on. • Confirm device is paired. LITHIUM-ION BATTERY WARNINGS This device contains a non-removable Lithium-Ion battery . The battery must be recycled or disposed of properly. Contact your local waste management office for information on battery recycling or disposal. WIRELESS SPEAKER SHENZHEN FENDA TECHNOLOGY CO., LTD. ONE (1) YEAR LIMITED WARRANTY Brookstone ® warrants this product against defects in materials and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (“Warranty Period”). If a defect arises and a valid claim is received within the Warranty Period, at its option, Brookstone will either 1) repair the defect at no charge, using new or refurbished replacement parts, or 2) replace the product with a new product that is at least functionally equivalent to the original product, or 3) provide a store credit in the amount of the purchase price of the original product. A replacement product or part, including a user-installable part installed in accordance with instructions provided by Brookstone, assumes the remaining warranty of the original product. When a product or part is exchanged, any replacement item becomes your property and the replaced item becomes Brookstone’s property. When a store credit is given, the original product must be returned to Brookstone and becomes Brookstone’s property. Obtaining Service: To obtain warranty service, call Brookstone Limited Warranty Service at 1-800-292-9819. Please be prepared to describe the product that needs service and the nature of the problem. A purchase receipt is required. All repairs and replacements must be authorized in advance. Service options, parts availability and response times will vary. You are responsible for delivery and the cost of delivery of the product or any parts to the authorized service center for replacement, per our instructions. Limits and Exclusions: Coverage under this Limited Warranty is limited to the United States of America, including the District of Columbia and the U.S. Territories of Guam, Puerto Rico, and the U.S. Virgin Islands. This Limited Warranty applies only to products manufactured for Brookstone that can be identified by the “Brookstone” trademark, trade name, or logo affixed to them or their packaging. The Limited Warranty does not apply to any non- Brookstone products. Manufacturers or suppliers other than Brookstone may provide their own warranties to the purchaser, but Brookstone, in so far as permitted by law, provides these products “as is.” This warranty does not apply to: a) damage caused by failur…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 SHENZHEN FENDA TECHNOLOGY CO., LTD. 2015-11-17 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ____ SHENZHEN FENDA TECHNOLOGY CO., LTD.__ _hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product： WIRELESS SPEAKER Trade Name： Brookstone Model Name： Floating Speaker Serial Model： N/A FCC ID： HBOFLOAT Sincerely, Signature Client’s name / title : frank Chenzhonghua / Engineer Contact information / address : Fenda Hi-Tech Park, Zhoushi Road, Shiyan Town, Baoan District, Shenzhen City,Guangdong,China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (obsolete) 3.0 4.0 March-26-2015 Corrections to STC form. Added reference to KDB (current) 4.0 5.0 Nov 19 2015 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 5.0 SHENZHEN FENDA TECHNOLOGY CO., LTD. 2015-12-07 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: HBOFLOAT Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signature Client’s name / title : frank Chenzhonghua / Engineer Contact information / address : Fenda Hi-Tech Park, Zhoushi Road, Shiyan Town, Baoan District, Shenzhen City,Guangdong,China

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

D C I n p u t : 5 V 1 A M a d e i n C h i n a POWER M o d e l : F l o a t i n g S p e a k e r S K U # : 9 9 4 0 8 0 F C C I D : H B O F L O A T

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 BT ANT

FCC ID: HBOFLOAT FCC §15.247 (i), §2.1091 – RF Exposure FCC ID:HBOFLOAT Applied procedures / limit According to FCC §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Note: ƒ is frequency in MHz * = Power density limit is applicable at frequencies greater than 100 MHz Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz * = Plane-wave equivalent power density MPE PREDICTION Predication of MPE limit at a given distance, Equation from OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna TEST RESULTS FCC ID: HBOFLOAT BT 1Mbps Test Channel Frequency (MHz) Peak Output Power (dBm) Peak Output Power (mW) CH00 2402 3.33 2.153 CH39 2441 3.10 2.042 CH78 2480 2.96 1.977 2Mbps CH00 2402 2.21 1.663 CH39 2441 2.01 1.589 CH78 2480 1.83 1.524 3Mbps CH00 2402 2.24 1.675 CH39 2441 2.03 1.596 CH78 2480 1.92 1.556 Mode Range Maximum peak output power (dBm) Output power (mW) Antenna Gain (numeric) Power Density (S) (mW/ cm 2 ) Limit of Power Density (S) (mW/ cm 2 ) Result 1Mbps 2~4 4 2.51 1(1.26) 0.0006 1 Pass 2Mbps 1~3 3 2.00 1(1.26) 0.0005 1 Pass 3Mbps 1~3 3 2.00 1(1.26) 0.0005 1 Pass

FCC RADIO TEST REPORT-BT FCC ID:HBOFLOAT Product： WIRELESS SPEAKER Trade Name： Brookstone Model Name： Floating Speaker Serial Model： N/A Report No.： NTEK-2015DC1116008F Prepared for SHENZHEN FENDA TECHNOLOGY CO., LTD. Fenda Hi-Tech Park, Zhoushi Road, Shiyan Town, Baoan District, Shenzhen City, Guangdong, China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 73 Report No.:NTEK-2015DC1116008F TEST RESULT CERTIFICATION Applicant’s name ................. : SHENZHEN FENDA TECHNOLOGY CO., LTD. Address ................................. : Fenda Hi-Tech Park, Zhoushi Road, Shiyan Town, Baoan District, Shenzhen City, Guangdong, China Manufacture's Name ............ : SHENZHEN FENDA TECHNOLOGY CO., LTD. Address ................................. : Fenda Hi-Tech Park, Zhoushi Road, Shiyan Town, Baoan District, Shenzhen City, Guangdong, China Product description Product name ........................... : WIRELESS SPEAKER Model and/or type reference : Floating Speaker Serial Model： N/A Standards ............................. : FCC Part15.247: 01 Oct. 2015 Test procedure .............................. ANSI C63.10-2013 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personnel only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 16 Nov. 2015 ~24 Nov. 2015 Date of Issue ........................................... : 24 Nov. 2015 Test Result ............................................... : Pass Testing Engineer : (Eileen Liu) Technical Manager : (Brown Lu) Authorized Signatory : (Sam Chen) Page 3 of 73 Report No.:NTEK-2015DC1116008F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 9 2.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 9 2.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 11 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3 . EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 3.1.2 TEST PROCEDURE 14 3.1.3 DEVIATION FROM TEST STANDARD 14 3.1.4 TEST SETUP 14 3.1.5 EUT OPERATING CONDITIONS 14 3.1.6 TEST RESULTS 15 3.2 RADIATED EMISSION MEASUREMENT 23 3.2.1 RADIATED EMISSION LIMITS 23 3.2.2 TEST PROCEDURE 24 3.2.3 DEVIATION FROM TEST STANDARD 24 3.2.4 TEST SETUP 25 3.2.5 EUT OPERATING CONDITIONS 26 3.2.6 TEST RESULTS (BELOW 30 MHZ) 27 3.2.7 TEST RESULTS (BETWEEN 30M – 1000 MHZ) 28 3.2.8 TEST RESULTS (ABOVE 1000 MHZ) 30 4 . NUMBER OF HOPPING CHANNEL 31 4.1 APPLIED PROCEDURES / LIMIT 31 4.1.1 TEST PROCEDURE 31 4.1.2 DEVIATION FROM STANDARD 31 4.1.3 TEST SETUP 31 4.1.4 EUT OPERATION CONDITIONS 31 4.1.5 TEST RESULTS 32 5 . AVERAGE TIME OF OCCUPANCY 33 5.1 APPLIED PROCEDURES / LIMIT 33 Page 4 of 73 Report No.:NTEK-2015DC1116008F Table of Contents Page 5.1.1 TEST PROCEDURE 33 5.1.2 DEVIATION FROM STANDARD 33 5.1.3 TEST SETUP 34 5.1.4 EUT OPERATION CONDITIONS 34 5.1.5 TEST RESULTS 35 6 . HOPPING CHANNEL SEPARATION MEASUREMENT 41 6.1 APPLIED PROCEDURES / LIMIT 41 6.1.1 TEST PROCEDURE 41 6.1.2 DEVIATION FROM STANDARD 41 6.1.3 TEST SETUP 41 6.1.4 EUT OPERATION CONDITIONS 41 6.1.5 TEST RESULTS 42 7 . BANDWIDTH TEST 48 7.1 APPLIED PROCEDURES / LIMIT 48 7.1.1 TEST PROCEDURE 48 7.1.2 DEVIATION FROM STANDARD 48 7.1.3 TEST SETUP 48 7.1.4 EUT OPERATION CONDITIONS 48 7.1.5 TEST RESULTS 49 8 . PEAK OUTPUT POWER TEST 55 8.1 APPLIED PROCEDURES / LIMIT 55 8.1.1 TEST PROCEDURE 55 8.1.2 DEVIATION FROM STANDARD 55 8.1.3 TEST SETUP 55 8.1.4 EUT OPERATION CONDITIONS 55 8.1.5 TEST RESULTS 56 9 . 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE 62 9.1 DEVIATION FROM STANDARD 62 9.2 TEST SETUP 62 9.3 EUT OPERATION CONDITIONS 62 9.4 TEST RESULTS 63 10 . ANTENNA REQUIREMENT 71 10.1 STANDARD REQUIREMENT 71 10.2 EUT ANTENNA 71 11 . EUT TEST PHOTO 72 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 73 Report No.:NTEK-2015DC1116008F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247(a)(1) Hopping Channel Separation PASS 15.247(b)(1) Peak Output Power PASS 15.247(c) Radiated Spurious Emission PASS 15.247(a)(iii) Number of Hopping Frequency PASS 15.247(a)(iii) Dwell Time PASS 15.247(a)(1) Bandwidth PASS 15.205 Band Edge Emission PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Page 6 of 73 Report No.:NTEK-2015DC1116008F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 73 Report No.:NTEK-2015DC1116008F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment WIRELESS SPEAKER Trade Name Brookstone Mo…

Text truncated - open the document above for the full version.

Page 72 of 73 Report No.:NTEK-2015DC1116008F 11. EUT TEST PHOTO Radiated Measurement Photos Page 73 of 73 Report No.:NTEK-2015DC1116008F CONDUCTED EMISSION Photos