I7CAYB06724LOW POWER TRANSMITTER

2270 HIWAY 54 IOLA, KS 66749 OWNERS MANUAL FOR AYB067 CIRCUIT: TABLE OF CONTENTS: INFORMATION TO USER: BLOCK DIAGRAM: GENERAL PURPOSE HEADER: CONNECTOR DRAWING: FCC I.D. LABLE INFORMATION TO USER: IF CHANGES OR MODIFICATIONS ARE DONE TO AYB067 CIRCUIT BOARD WITH OUT EXPRESSLY APPROVED BY THE PARTY RESONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE:THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE,PURSUANT TO PART 15 OF THE FCC RULES.THESE LIMITS ARE DESIGN TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERANCE IN A RESIDENTIAL INSTALLATION.THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS,MAY CAUSE HARMFUL INTERFERANCE TO RADIO COMMUNICATIONS.HOWEVER, THERE IS NO GUARANTEE THAT INTERFERANCE WILL NOT OCCUR IN A PATICULAR INSTALLATION.IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERANCE TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERANCE BY ONE OR MORE OF THE FOLLOWING MEASURES. - REORIENT OR RELOCATE THE RECEIVING ANTENNA. - INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER. - CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE RECEIVER IS CONNECTED. CONSULT THE DEALER OR AN EXPERIENED RADIO/TV TECHNICIAN FOR HELP. BLOCK DIAGRAM: GENERAL PUPOSE HEADER: SERIAL 1: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 GND 2 PTE O/Tx D1 GENERAL PURPOSE 3.3 VOLT LOGIC 3 PTE 1/Rx D1 DIGITAL I/O UART SERIAL 2: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 GND 2 PTC 0/Tx D2 GENERAL PURPOSE 3.3 VOLT LOGIC 3 PTC 1/Rx D2 DIGITAL I/O UART CN 1: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 8 PTA 0 7 PTA 1 GENERAL PURPOSE CAN WAKE MCU FROM 6 PTA 2 DIGITAL I/O STOP 3 OR WAIT MODE. 5 PTA 3 CAN DETECT FALLING/RISING 4 PTA 4 EDGES WHEN KEYBOARD 3 PTA 5 INTERRUPT IS ENABLING. 2 PTA 6 1 PTA 7 A PTD 0 B PTD 1 C PTD 2 D PTD 3 E PTD 4 CN 3: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 VCC/3.3 VOLT 2 PTB 7 ANALOG INPUT OR CONNECTED TO MCU 3 PTB 6 GENERAL PUPOSE ANALOG TO DIGITAL 4 PTB 5 DIGITAL I/O 10 BIT A/D CONVERTER, 5 PTB 4 CHANNELS 0-7. 6 PTB 3 7 PTB 2 8 PTB 1 9 PTB 0 10 GND CN 4: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 GPIO 7 2 GPIO 6 GENERAL PURPOSE COMMUNICATES TO MCU 3 GPIO 5 DIGITALI/O ON RF. THRU SPI PORT. 4 GPIO 3 5 GND CN 5: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 GND 2 PTE 2 SLAVE SELECT SPI USED FOR RF AND 3 PTE 3 MISO SPI THE PROCESSOR TO 4 PTE 4 MOIS SPI SERIAL COMMUNICATION. 5 PTE 5 SPSCK SPI 6PIN: HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 GND POWER GROUND 2 POWER 3.5v TO 29v 3 GND POWER GROUND 4 GND BOARD GROUND 5 ENABLE ALLOWS UNIT TO POWER UP WHEN ON 6 PTA 7,PTA 6 EN-3 COMMUNICATES TO PTA 5,PTA 4 PROCESSOR THAT POWER SWITCH IS OFF. J101 PROGRAMMING HEADER : HDR. PIN MCU PORT/PIN FUNCTION REMARKS 1 PTG 0/BK GO SERIAL PROGRAMMING GENERAL PUPOSE I/O ACTIVE LOW RESET. 2 GND GROUND 3 NC NC 4 RESET RESET TO MCU 5 NC NC 6 VCC PROVIDES POWER CONNECTOR DRAWING: FCC I.D. LABLE 1.1INCHS 1.5 INCHS FCC ID: I7CAYB06724 CANADA ID: ---------------------------------------------------- MICROTRONICS, INC. PH-620-365-8264 “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.” S/N 0 0 0 0 0 0

March 26, 2007 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Office of Engineering and Technology Federal Communications Commission Columbia, MD 21046 Applicant: Microtronics, Inc. 2270 Hwy. 54 Iola, KS 66749 Re: Confidentiality for submittal information regarding FCC ID number I7CAYB06724 PRODUCT: Low Power Transmitter operating in the 2400-2483.5 MHz frequency band under part 15.249. Dear Sirs: Microtronics, Inc. requests that the material in the Block Diagram, Schematics, and Operational Description be withheld from public disclosure in accordance with Section 0.459 of the Commissions Rules, 47 C.F.R. 0.459 (1998), following grant of the application. In support of this request, Microtronics, Inc. submits the following. Short term confidential files External Photographs B067B EUT Photos.pdf Internal Photographs B067B Internal Photos.pdf Test Setup B067B Test Setup Photo.pdf User Manual AYB067 owners manual.pdf Permanent Confidential files Block Diagram B067B Block Diagram.pdf Operational Description B067B Theory of Operation.pdf Schematics B067Btx.pdf 1. Identification of the specific information for which confidential treatment is sought: The materials set fourth in the Operational Description, block diagram, and Schematics, which are segregated from the non-confidential exhibits of the application, are those for which confidentiality is sought. 2. Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission: The proceeding is that involving the application for equipment authorization (certification) under FCC ID: I7CAYB06724 ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 3. Explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged: This material includes a detailed theory of operation, circuit diagrams, (schematic diagrams) and detail Parts List. As such, this material is treated as highly confidential business information. 4. Explanation of the degree to which the information concerns a service that is subject to competition: The material for which confidentiality is sought is employed in the design and manufacture of this transmitting equipment that is offered on a highly competitive basis. Customers for this equipment have a variety of competing sources. 5. Explanation of how disclosure of the information could result in substantial competitive harm: Disclosure would, in effect, give away the fruits of the labors of Microtronics, Inc.’s engineering personnel, who have designed the equipment and the manufacturing process. Disclosure would also offer competitors additional unwarranted insight into the state of the product development, thereby allowing competitors an advantage, not available to Microtronics, Inc. 6. Identification of any measures taken by the submitting party to prevent unauthorized disclosure: The information for which confidential treatment is sought is kept confidential by Microtronics, Inc. and not made available to third parties except pursuant to non-disclosure agreements. 7. Identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties: To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. While the general theory of operation of this equipment has been the subject of numerous disclosures in industry and standards groups as well as in rule making proceedings of the FCC, the protection sought is narrowly drawn and pertains to certain specific implementations of this radio technology. 8. Justification of the period during which the submitting party asserts that the material should not be available for public disclosure: This material should not be disclosed for at least 25 years. While improvements in design are made relatively frequently, disclosure of the design information would lead to insights into both design and manufacturing techniques that could have an adverse competitive effect for many years to come. This equipment is designed for commercial, industrial, and governmental applications. As such, unlike most consumer equipment, this equipment could be used for more than a decade in some cases. As such, it is important that the design not be made available to unauthorized persons who might attempt to use knowledge of the design to compromise the applications for which the equipment will be employed. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers

March 26, 2007 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Office of Engineering and Technology Federal Communications Commission Columbia, MD 21046 Applicant: Microtronics, Inc. 2270 Hwy. 54 Iola, KS 66749 FCC ID: I7CAYB06724 Re: Confidentiality for submittal information regarding FCC ID number I7CAYB06724 Product: Low Power Transmitter operating in the 2400-2483.5 MHz frequency band operating under part 15.249. Dear Sirs: Microtronics, Inc. requests that the following information be withheld from public disclosure until 45 days after the Grant of Equipment Authorization in accordance with DA-04-1705 of the Commission’s public notice. Short-term confidential files External Photographs B067B EUT Photos.pdf Internal Photographs B067B Internal Photos.pdf Test Setup B067B Test Setup Photo.pdf User Manual AYB067 owners manual.pdf Permanent Confidential files Block Diagram B067B Block Diagram.pdf Operational Description B067B Theory of Operation.pdf Schematics B067Btx.pdf Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053

Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 1 of 1 B067B EUT Photos 3/26/2007 Equipment photographs for B067B.

Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 1 of 1 B067B ID Label 3/26/2007 FCC ID label information for B067B. FCC ID: I7CAYB06724 CANADA ID: ---------------------------------------------------- MICROTRONICS, INC. PH-620-365-8264 “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.” S/N

Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 1 of 1 B067B Internal Photos 3/26/2007 Internal photographs for B067B

Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 1 of 1 B067B Tune 3/26/2007 B067B tuning The unit has no provisions for tuning. It is produced and tested using a pass on pass operation.

Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 1 of 1 B067B MPE Calculation 3/26/2007 MPE CalculatorMicrotronicsTest 070227 MPE uses EIRP for calculation. EIRP is based on TX power added to the antenna gain in dBi. dBi = dB gain compared to an isotropic radiator. S = power density in mW/cm^2Antenna Gain (dBi)1 Output PowerdBd + 2.17 = dBidBi to dBd2.17 Tx Frequency (MHz)2440(Watts)0.0010Antenna Gain (dBd)-1.17 Cable Loss (dB)0.0(dBm)0.00Antenna minus cable (dBi)1.00 Calculated ERP (mw) 0.764EIRP = Po(dBM) + Gain (dB) Calculated EIRP (mw) 1.259Radiated (EIRP) dBm1.000 ERP = EIRP - 2.17 dB Occupational LimitOccupational LimitRadiated (ERP) dBm-1.170 8.13333 mW/cm 2 300-1500 MHz5 mW/cm 2 1500-10000 MHz General Public LimitGeneral Public Limit 1500-10000 MHz 1.62667 mW/cm 2 300-1500 MHz 1 mW/cm 2 Frequency (MHz)Occupational LimitPublic Limit 300-1,500f/300f/1500 1,500-10,00051 Frequency (MHz) Occupational Limit @ Tx Freq (mW/cm^2) Public Limit @ Tx Freq (mW/cm^2) 300-1,5008.1333333331.626666667 1,500-10,00051 EIRPDistanceDistanceS milliwattscminchesmW/cm 2 1.25950.0019.690.00004 1.25940.0015.750.00006 1.25930.0011.810.00011 1.25925.009.840.00016 1.25920.007.870.00025 1.25915.005.910.00045 1.25914.005.510.00051 1.25913.005.120.00059 1.25912.004.720.00070 1.25911.004.330.00083 1.25910.003.940.00100 1.2599.003.540.00124 1.2598.003.150.00157 1.2597.002.760.00204 1.2596.002.360.00278 1.2595.001.970.00401 1.2594.001.570.00626 1.2593.001.180.01113 1.2592.000.790.02505 1.2591.500.590.04453 1.2591.250.490.06412 1.2591.000.390.10018 1.2590.750.300.17810 1.2590.500.200.40073 1.2590.350.140.81781 Frequency (MHz) Occupational Limit minimum Distance (cm) Public Limit minimum distance (cm) 300-1,500N/AN/A 1,500-10,000N/A0.35 FCC radio frequency radiation exposure limits per 1.1310 FCC radio frequency radiation exposure limits per 1.1310 Power density (S) EIRP ------- = mW/cm^2 4 π r^2 r (cm) EIRP (mW)

SUBMITTAL APPLICATION REPORT FOR GRANT OF CERTIFICATION FOR MODEL: B067B 2.4 Transceiver 2400-2483.5 MHz Transmitter FOR MICROTRONICS, INC. 8 North Washington Iola, KS 66749 Test Report Number: 070227 NVLAP Accredited Laboratory NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 2 of 29 Microtronics B067B Test Report.doc 3/28/2007 ENGINEERING TEST REPORT FOR APLLICATION of GRANT of CERTIFICATION FOR CFR47, PART 15C - INTENTIONAL RADIATORS Paragraph 15.249, Low Power Transmitter Industry Canada, RSS-210 For MICROTRONICS, INC. 8 North Washington Iola, KS 66749 Roger Jones, Model: B067B 2.4 Transceiver wireless transmitter Frequency 2400-2483.5 MHz FCC ID#: I7CAYB06724 Test Date: February 27, 2007 Certifying Engineer: Scot D. Rogers ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone: (913) 837-3214 FAX: (913) 837-3214 This report shall not be reproduced except in full, without the written approval of the laboratory. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214 NVLAP Accredited Laboratory NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 3 of 29 Microtronics B067B Test Report.doc 3/28/2007 TABLE OF CONTENTS FORWARD..................................................................................................................... 4 1) APPLICABLE STANDARDS & TEST PROCEDURES........................................... 4 2.1033(b) Application for Certification..........................................................................................................5 2) EQUIPMENT TESTED ............................................................................................ 6 3) EQUIPMENT FUNCTION AND TESTING PROCEDURES..................................... 6 4) EQUIPMENT AND CABLE CONFIGURATIONS .................................................... 7 Conducted Emission Test Procedure..................................................................................................................7 Radiated Emission Test Procedure.....................................................................................................................7 5) LIST OF TEST EQUIPMENT................................................................................... 8 6) UNITS OF MEASUREMENTS................................................................................. 9 7) TEST SITE LOCATIONS......................................................................................... 9 8) SUBPART B – UNINTENTIONAL RADIATORS .................................................... 9 Conducted EMI ....................................................................................................................................................9 Radiated EMI .....................................................................................................................................................10 General Radiated Emissions Data from EUT ....................................................................................................13 Summary of Results for Conducted Emissions ...............................................................................................13 Summary of Results for Radiated Emissions ..................................................................................................14 Statement of Modifications and Deviations .....................................................................................................14 9) SUBPART C - INTENTIONAL RADIATORS ........................................................ 14 15.203 Antenna Requirements ..........................................................................................................................14 15.205 Restricted Bands of Operation..............................................................................................................14 Radiated Emissions Data in Restricted Bands (15.205) ....................................................................................15 Summary of Results for Radiated Emissions in Restricted Bands ................................................................15 15.209 Radiated Emissions Limits; General Requirements ...........................................................................16 Radiated EMI.....................................................................................................................................................16 General Radiated Emissions Data from EUT (15.209) .....................................................................................17 Summary of Results for Radiated Emissions ..................................................................................................17 15.249 Operation in the Band 2400-2483.5 MHz ............................................................................................17 Radiated Emissions Data from EUT (15.249) ...................................................................................................23 Summary of Results for Radiated Emissions of Intentional Radiator ..........................................................24 Statement of Modifications and Deviations .....................................................................................................24 APPENDIX .................................................................................................................... 25 NVLAP Accredited Laboratory NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Microtronics, Inc. 4405 …

Text truncated - open the document above for the full version.

Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 1 of 2 B067B Test setup Photo 3/26/2007 Test setup photographs for B067B Rogers Labs, Inc. Microtronics, Inc. 4405 W. 259th Terrace Model: B067B 2.4 Transceiver FCC ID#: I7CAYB06724 Louisburg, KS 66053 Test #: 070227 IC: Phone/Fax: (913) 837-3214 Test to: CFR47 15c (15.249), IC RSS-210 Page 2 of 2 B067B Test setup Photo 3/26/2007