I7OBT-24HBluetooth Headset

User manual Wireless Speaker Microphone 2 This product is designed to radiate low levels of radio energy in accordance with global government approved regula- tory standards. It features Adaptive Power Output. APO automatically adjusts the RF power output in accordance with signal required. This features limits and reduces extraneous radiated radio energy. This also helps minimize battery consumption and extends battery shift life. Do not touch the antenna when operational. Keep it 1.5 cm (5/8 inch) or more away from your body to ensure exposure levels remain at or below the maximum levels. Table of Contents Parts & Functions ���������������������������������������������������4 Carry Clip Removal�����������������������������������������������5 Operation Description ������������������������������������������6 Basic Operation ����������������������������������������������������8 •Power On & Off................................................8 •Volume Control ................................................8 •Transmitting/Receiving ....................................8 •Emergency (optional) .....................................8 •Multiple unit operation ....................................9 •Motorcycle operation .....................................9 •Headset - Covert operation ...........................9 Technical Notes���������������������������������������������������10 •Battery Charging ...........................................10 •Replacing the battery pack ........................11 •Re-connection ...............................................12 •Microphone adjustment ...............................12 •Antenna choice & replacement .................13 •Installation & Connections ...........................14 •Alternate configurations ...............................16 •Approvals, Warranty & Warnings .................18 •Important safety and handling ....................20 •Specifications .................................................23 3 Antenna Manual Off/On Emergency PTT: Press-To-Talk Volume up Volume down Headset connector (Optional) Earpiece jack DC charging Microphone Loudspeaker Parts and functions Volume up: adjusts speaker audio louder. Volume down: adjust speaker audio softer - minimum setting. Microphone: talk in a normal strength voice about 3 to 5cm (2”). PTT: press to talk - beeps if pressed when out of range Emergency: triggers host radio’s emergency function. Hold down as per mobile radio’s emergency button operating instructions - The unit will beep if pressed when out of range. Manual off/on: hold for about 3 seconds to turn on or off. The spk mic will sound escalating or de-escalating tone to advise status. *Normal configuration see Installation section for alternatives. **Buy separately as needed. Status light (optional) Status light Manual Off/On Charging contacts 4 Connector SMA Carry Clip Removal Standard spring belt clip This is the traditional type most users are familiar with. It allows the Spk Mic to be clipped to work vests, clothing, epaulettes, etc. For maximum performance 360º around your vehicle it is recom- mended that it be worn in a location that allows the antenna to protrude above you body. The antenna should always be lo- cated os that To remove follow these three photos: Locate the metal securing tag - Press the tag away from the Spk Mic whilst sliding the clip upwards. Identify release tag Push out while sliding clip up 5 DC charging: place into charger to automatically re-charge. Headset connector: use with associated** headsets/accessories. Earpiece jack: allows private listening via 3.5mm mono earpiec- es.** The loudspeaker is disabled when 3.5mm plug is inserted. Loudspeaker: Delivers loudspeaker audio - Automatically turns off when inserted into mobile/base charger.* Status light: glows blue when connected and operational. It will flash when “out of range” or when the mobile charger unit is off. Operation Description Congratulations on choosing the revolutionary Wireless Speaker Microphone. This incredibly compact, light- weight personal accessory extends the power of the mobile radio to the palm of your hand, whether in and out of the vehicle. It stands ready to re-define mobile network design by increasing user functionality and mobility whilst dramatically improving the effectiveness of your infrastructure investment. This visionary solution provides users out of vehicle communications with the power and performance of their mobile radio. It cuts the cord and for the first time puts the micro- phone and radio system access into the palm of the users hand when away from the vehicle, delivering true mobility without system compromise. Users can feel to- tally confident their private communications are kept securedue to the smart 64 bit/128 bit encryption (model dependent) functionality. The Wireless Speaker Microphone uniquely incorporates “hard wire coding” connection protocol that eliminates any possibility of outside intrusion between the unit and your vehicle’s mobile. It unleashes the power of your mobile radio allowing wireless communication with a fixed mounted or vehi- cle radio: 60, 150, 300 metres or more*. Now users can communicate with enhanced clear audio, with the power and range of their mobile radio, while not being tied to the vehicle allowing the user to be truly mobile in every operational environment. Finally, if you go out of range, the blue LED will flash and the unit will sound a warning tone if you press the PTT or optional Emergency button, so you will know to move back into your communication zone or, to be simply aware. This ability to now communicate whilst outside your vehicle is a great assistance to enhancing a safer and more secure work environment for everyone who carries a Wireless Speaker Microphone. 6 60m.... 150m.... 300m... *Range is always dependent on the local terrain and communications environment. A variety of antenna configurations are available to enhance in-building penetration or, simply t…

Text truncated - open the document above for the full version.

910805 2 Date: 2012-05-15 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: We, the undersigned, hereby authorize ELECTRONICS TESTING CENTER, TAIWAN, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by ELECTRONICS TESTING CENTER, TAIWAN on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; 910805 3 e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, (signature) Jack Chen/ Vice President Rexon Technology Corp No 261, Jen Hwa Road, Tali, Taichung, Taiwan

910805 1 Federal Communications Commission FCC ID:I7OBT-24H Product Name: Bluetooth Headset Model Name: BT-24H, X10DRSM , JD-900B Trade Name : Rexon , Wireless Pacific ,JDI Dear Sir: In accordance with 47 C.F.R. Section 0.459, we would like to request confidentiality on some exhibits we submitted for above application for the reason of trade secret. If those exhibits are available for public inspection, any person who once gets the information contained in those exhibits will be able to design and to make the same products very easily. This is a very serious problem and huge loss for us, because we did invest so much on it. Please be not made the Exhibit Types listed below routinely available for public inspection: Block Diagram and Schematics and Operation Description. By: By: Jack Chen (Signature) (Printed) Title : Vice President Applicant : Rexon Technology Corp Address : No 261, Jen Hwa Road, Tali, Taichung, Taiwan Tel : 886-4-2491-4141 Fax: 886-4-24912042

ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 1 of 6 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT (EUT) 1. 2. ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 2 of 6 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 3. 4. ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 3 of 6 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 5. 6.

FCC ID: I7OBT-24D FCC ID: I7OBT-24H 29*12mm 29*12mm

ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 4 of 6 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 7. 8. ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 5 of 6 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 9. 10. ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 6 of 6 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 11. 12.

Model No. Application ▪IEEE 802.11 WLAN System ▪Wireless Communication System ▪Wi-Fi / WLAN / MIMO / Bluetooth System Features ▪RoHS Compliant ▪Low V.S.W.R. / Low Loss Design / High Gain ▪High Efficiency and Sensitivity ▪Low Loss RF Coaxial Connector Cable Feed ▪Matching Free Design Specification H-Plane Radiation Pattern Dimension E-Plane Radiation Pattern 2.4 GHz Antenna for IEEE 802.11 WLAN System or Bluetooth 0 45 90 135 180 225 270 315 0 0 -10 -10 -20 -20 -30 -30 -40 -40 0 45 90 135 180 225 270 315 0 0 -10 -10 -20 -20 -30 -30 -40 -40 AN2400-1401RS ▪Freq. : 2.4 - 2.5 GHz ▪S.W.R. : <= 2.0 ▪Gain : 2 dBi ( * Typical * ) ▪Radiation Pattern : Omni-Directional ▪Connector : SMA Male Reverse ▪TPE 80~85

©2012 A Test Lab Techno Corp. A Test Lab Techno Corp. Changan Lab：No. 140 -1, Changan Street, Bade City, Taoyuan County, Taiwan R.O.C. Te l：886-3-271-0188 / Fax：886-3-271-0190 SAR EVALUATION REPORT Test Report No. ： 1207FS19-03 Applicant ： Rexon Technology Corp Product Type ： Bluetooth Headset Trade Name ： Rexon , Wireless Pacific ,JDI Model Number ： BT-24H, X10DRSM ,JD-900B FCC ID ： I7OBT-24H Date of Received ： Jul. 06, 2012 Dates of Test ： Jul. 19 ~ Jul. 21, 2012 Date of Issued ： Aug. 31, 2012 Test Environment ： Ambient Temperature： 22 ± 2 ° C Relative Humidity：40 - 70 % Standard ： ANSI/IEEE C95.1-1999 IEEE Std. 1528-2003 IEEE Std. 1528a-2005 47 CFR Part §2.1093; FCC/OET Bulletin 65 Supplement C [July 2001] Max. SAR ： 0.035 W/kg Body SAR Test Lab Location ： Chang-an Lab 1. The test operations have to be performed with cautious behavior, the test results are as attached. 2. The test results are under chamber environment of A Test Lab Techno Corp. A Test Lab Techno Corp. does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples. 3. The measurement report has to be written approval of A Test Lab Techno Corp. It may only be reproduced or published in full. This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. The test results in the report only apply to the tested sample. Approved By ： Tested By ： (Yung Tan Tsai ) (Bill Hu) Report Number: 1207FS19-03Page 1 of 63 Contents 1. Description of Equipment under Test (EUT)....................................................................................... 3 2. Introduction......................................................................................................................................... 4 2.1 SAR Definition ............................................................................................................................ 4 3. SAR Measurement Setup................................................................................................................... 5 3.1 DASY5 E-Field Probe System ................................................................................................... 6 3.2 Data Acquisition Electronic (DAE) System................................................................................. 9 3.3 Robot.......................................................................................................................................... 9 3.4 Measurement Server.................................................................................................................. 9 3.5 Device Holder........................................................................................................................... 10 3.6 Phantom - SAM v4.0 ................................................................................................................ 10 3.7 Oval Flat Phantom - ELI 4.0......................................................................................................11 3.8 Data Storage and Evaluation ....................................................................................................11 4. Tissue Simulating Liquids................................................................................................................. 14 4.1 Ingredients................................................................................................................................ 15 4.2 Recipes .................................................................................................................................... 15 4.3 Liquid Confirmation .................................................................................................................. 16 5. SAR Testing with RF Transmitters.................................................................................................... 18 5.1 SAR Testing with Bluetooth Transmitters ................................................................................. 18 5.2 Conducted Power..................................................................................................................... 18 6. System Performance Check............................................................................................................. 19 6.1 Symmetric Dipoles for System Verification .............................................................................. 19 6.2 Verification................................................................................................................................ 20 7. Test Equipment List .......................................................................................................................... 23 8. Measurement Uncertainty ................................................................................................................ 24 9. Measurement Procedure.................................................................................................................. 26 9.1 Spatial Peak SAR Evaluation ................................................................................................... 26 9.2 Area & Zoom Scan Procedures ...............................................................................................27 9.3 V olume Scan Procedures......................................................................................................... 27 9.4 SAR Averaged Methods ........................................................................................................... 27 9.5 Power Drift Monitoring.............................................................................................................. 27 10. SAR Test Results Summary ........................................................................................................... 28 10.1 Body SAR........................................................................................................................…

Text truncated - open the document above for the full version.

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. : Bluetooth Headset Model : BT-24H, X10DRSM, JD-900B FCC ID : 17OBT-24H for APPLICANT : Rexon Technology Corp ADDRESS : No 261, Jen Hwa Road, Tali, Taichung, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5. DINGFU, LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail : [email protected] Report Number : 12-05-RBF-018-05 ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : Rexon Technology Corp No 261, Jen Hwa Road, Tali, Taichung, Taiwan Manufacture : Rexon Technology Corp No 261, Jen Hwa Road, Tali, Taichung, Taiwan Description of Device : a) Type of EUT : Bluetooth Headset b) Trade Name : Rexon, Wireless Pacific, JDI c) Model No. : BT-24H, X10DRSM, JD-900B d) Power Supply : DC 3.7V,1200mAh Battery Regulation Applied : FCC Rules and Regulations Part 15 Subpart C I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Summary of Tests Test Results Radiated Emission Pass Conducted Emission Pass Hopping Channel Separation Pass Number of Hopping frequencies used Pass Hopping Channel Bandwidth Pass Dwell Time of each frequency Pass Output Power Requirement Pass 100 kHz Bandwidth of Frequency Band Edges Requirement Pass Out-of-Band Conducted Emission Requirement Pass ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Rev. No 1.0 Date Test Item Received : May 03, 2012 Date Test Campaign Completed : Jul. 16, 2012 Date of Issue : Jul. 30, 2012 Test Engineer : ( Vincent Chang, Engineer ) Approve & Authorized : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 1 1.1 Product Description...................................................................................................................... 1 1.2 Test Methodology ........................................................................................................................ 1 1.3 Test Facility.................................................................................................................................. 1 2 PROVISIONS APPLICABLE...................................................................................................... 2 2.1 Definition ..................................................................................................................................... 2 2.2 Requirement for Compliance ....................................................................................................... 3 2.3 Restricted Bands of Operation ..................................................................................................... 5 2.4 Labeling Requirement .................................................................................................................. 6 2.5 User Information .......................................................................................................................... 6 3 SYSTEM TEST CONFIGURATION .......................................................................................... 7 3.1 Justification .................................................................................................................................. 7 3.2 Devices for Tested System........................................................................................................... 7 4 RADIATED EMISSION MEASUREMENT .............................................................................. 8 4.1 Applicable Standard ..................................................................................................................... 8 4.2 Measurement Procedure............................................................................................................... 8 4.3 Measuring Instrument ................................................................................................................ 10 4.4 Radiated Emission Data ............................................................................................................. 11 4.5 Field Strength Calculation.......................................................................................................... 15 4.6 Photos of Radiation Measuring Setup........................................................................................ 16 5 CONDUCTED EMISSION MEASUREMENT ........................................................................ 17 5.1 Description ................................................................................................................................. 17 6 ANTENNA REQUIREMENT .................................................................................................... 18 6.1 Standard Applicable ................................................................................................................... 18 6.2 Antenna Construction................................................................................................................. 18 7 HOPPING CHANNEL SEPARATION..................................................................................... 19 7.1 Standard Applicable ................................................................................................................... 19 7.2 Measurement Procedure.........................................................................................................…

Text truncated - open the document above for the full version.

ETC Report No. : 12-05-RBF-018-05 FCC ID.: 17OBT-24H Sheet 16 of 63 Sheets Rev. No 2.1 4.6 Photos of Radiation Measuring Setup

SAR Test Setup Photographs Flat_Front surface to phantom 10mm Figure 1. Body SAR Test Setup (Flat Section) EUT Front side ©2012 A Test Lab Techno Corp. Report Number: 1207FS19-03Page 1 of 4 Flat_Back surface to phantom 10mm Figure 2. Body SAR Test Setup (Flat Section) EUT Back side ©2012 A Test Lab Techno Corp. Report Number: 1207FS19-03Page 2 of 4 Flat_Front surface to phantom 10mm_belt clip Figure 3. Body SAR Test Setup (Flat Section) EUT Front side ©2012 A Test Lab Techno Corp. Report Number: 1207FS19-03Page 3 of 4 ©2012 A Test Lab Techno Corp. Report Number: 1207FS19-03Page 4 of 4 Flat_Back surface of belt clip to phantom 0mm Figure 4. Body SAR Test Setup (Flat Section) EUT Back side