IPH-0P3039Outdoor Product

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January 21, 2026 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: IPH-0P3039 Garmin International, Inc., Garmin certifies that, as of the date of the filing of the application, Garmin International, Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Garmin International, Inc., accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Garmin International, Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. Designated U.S. Agent Information: FRN: 0005088588 Name: Garmin International, Inc. Address: 1200 East 151 st Street, Olathe, Kansas, 66062 Contact Person: Ben Karsak Tel.: 913-440-1946 Email: [email protected] Sincerely, Ben Karsak Manager Compliance Engineering

Rev 1/27/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January 7, 2026 Ref: Attestation Statements Part 2.911(d)(5) FCC ID: IPH-0P3039 FRN: 0005088588 Garmin International, Inc., (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Garmin International, Inc., (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Garmin International, Inc., (“the applicant”) certifies that, the device does not have cybersecurity and/or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered List installed on the device, nor will it be installed by the applicant after certification. Sincerely, Jacky Yeung Senior Compliance Engineer Garmin International, Inc.

Date: October 29, 2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality FCC ID: IPH-0P3039 To whom it may concern: Short-term confidentiality Pursuant to DA 04-1705 of the Commission’s pubic notice, in order to comply with the marketing regulations in 47CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after issue date ☒ Internal Photographs ☒ External Photographs ☒ User's manual ☒ Test Set up photo Permanent confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: ☒ Block Diagram ☒ Schematics ☒ Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter Applicant : Garmin International, Inc. Address : 1200 E. 151st Street Olathe, KS 66062 United States Signature : _________________________________ Name and Job Title. : Jacky Yeung / Senior Compliance Engineer E-mail : [email protected] Tel. : (984) 477-8401

Date: 2025/10/29 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: IPH-0P3039 Product name: Outdoor Product To whom it may concern: We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for FCC equipment authorization, including the signing of all documents relating to these matters. International Certification Corp. Address : No.3-1, Lane 6, Wen San 3rd St. Kwei Shan Dist., TaoYuan City 333, Taiwan (R.O.C.) Name : Gary Chang Job Title : Manager e-mail : [email protected] Webs We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. Applicant : Garmin International, Inc. Address : 1200 E. 151st Street Olathe, KS 66062 United States Signature : _________________________________ Name and Job Title. : Jacky Yeung / Senior Compliance Engineer E-mail : [email protected] Tel. : (984) 477-8401

April 16, 2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Innovation, Science and Economic Development Canada Certification and Engineering Bureau 3701 Carling Avenue PO Box 11490, Station H Ottawa, Ontario, Canada K2H 8S2 To Whom It May Concern: Pursuant to 47 CFR 2.911, Garmin International, Inc. (Garmin) has authorized the following Garmin International Associates to act on Garmin's behalf for the sole and express purpose of processing applications to the Federal Communication Commission (FCC) and Innovation, Science and Economic Development Canada (ISED) for equipment authorization or certification. Mr. Niklas Haydon, Compliance Engineering Team Lead Ms. Sara Jones, Design Certification Engineer Mr. Mitchell Phillipi, Compliance Engineering Team Lead Mr. Jacky Yeung, Compliance Engineer Mr. William Pertner, Compliance Engineering Team Lead Mr. Hayden Pernia, Compliance Engineer Mr. Jay Everett, Compliance Engineering Team Lead Mr. Jeremiah Darden, Compliance Engineer Mr. Richard Kockelkoren, Compliance Engineer Mr. Henry Lin, Compliance Engineer Mr. Mike Moranha, Compliance Engineer Ms. Claire Fryman, Compliance Engineer Ms. Pam Sequeira, Compliance Engineer Mr. Rick Jankovics, Compliance Engineer Mr. Jeffrey Hailey, Compliance Engineer Mr. Brodie Halbfoster, Compliance Engineer Mr. Dan Irish, Compliance Engineer Mr. Tim Olson, Compliance Engineer Mr. Jonathan Shafer, Design Certification Engineer As such, the Garmin Associates listed above are authorized to: 1) sign Form 731, 2) sign letters of application, 3) request confidentiality, and 4) exchange data and information with the FCC, IC and/or authorized TCBs on behalf of Garmin. In addition, these individuals shall be considered "authorized individuals" to act on Garmin's behalf where an "authorized individual's" attestation is necessary or preferred. This authorization remains in effect until notified to the contrary by Garmin. Sincerely, Ben Karsak Manager Compliance Engineering Garmin International, Inc.

Bottom side of EUT

Report No.: FA590201 Page : 1 of 6 Report Version: Rev. 01 FCC RF Exposure Report FCC ID : IPH-0P3039 Equipment : Outdoor Product Model No. : A0P3039 Brand Name : GARMIN Applicant : Garmin International, Inc. Address : 1200 E. 151st Street Olathe, KS 66062 United States Standard : 47 CFR FCC Part 2.1091 Received Date : Sep. 02, 2025 Tested Date : Dec. 05 ~ Dec. 08, 2025 We, International Certification Corporation, would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It shall not be reproduced except in full without the written approval of our laboratory. Reviewed by: Approved by: Along Chen / Manager Gary Chang / Manager Report No.: FA590201 Page : 2 of 6 Report Version: Rev. 01 Table of Contents 1 EXPOSURE EVALUATION OF PORTABLE DEVICES ....................................................................... 4 1.1 SAR TEST EXCLUSION THRESHOLD FOR 100MHz to 6GHz and  50mm................................... 4 1.2 DEVIATION FROM TEST STANDARD AND MEASUREMENT PROCEDURE ................................... 5 1.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 5 1.4 EVALUATION RESULTS ....................................................................................................................... 5 2 TEST LABORATORY INFORMATION ................................................................................................. 6 Report No.: FA590201 Page : 3 of 6 Report Version: Rev. 01 Release Record Report No. Version Description Issued Date FA590201 Rev. 01 Initial issue Jan. 09, 2026 Report No.: FA590201 Page : 4 of 6 Report Version: Rev. 01 1 EXPOSURE EVALUATION OF PORTABLE DEVICES 1.1 SAR TEST EXCLUSION THRESHOLD FOR 100MHz to 6GHz and  50mm Frequency (MHz) 5 10 15 20 25 Separation distance (mm) 150 39 77 116 155 194 SAR Test Exclusion Threshold (mW) 300 27 55 82 110 137 450 22 45 67 89 112 835 16 33 49 66 82 900 16 32 47 63 79 1500 12 24 37 49 61 1900 11 22 33 44 54 2450 10 19 29 38 48 3600 8 16 24 32 40 5200 7 13 20 26 33 5400 6 13 19 26 32 5800 6 12 19 25 31 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where •f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Report No.: FA590201 Page : 5 of 6 Report Version: Rev. 01 1.2 DEVIATION FROM TEST STANDARD AND MEASUREMENT PROCEDURE None 1.3 MEASUREMENT UNCERTAINTY The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2)). Parameters Uncertainty Conducted power ±0.808 dB Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. 1.4 EVALUATION RESULTS Maximum Conducted Output Power Result Modulation Mode Average Power (dBm) Tune up Power (dBm) Tune up Power (mW) Distance (mm) Threshold SAR Test Exclusion Thresholds LE-1Mbps 7.46 9 7.94 5 2.5 3 LE-2Mbps 7.45 9 7.94 5 2.5 3 Thresholds is < SAR test exclusion thresholds. Thus, SAR test is not required. Report No.: FA590201 Page : 6 of 6 Report Version: Rev. 01 2 Test laboratory information Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corporation (EMC and Wireless Communication Laboratory), it is our definitive objective is to institute long term, trust-based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan District. Location map can be found on our website https://www.icertifi.com.tw. Linkou Kwei Shan Kwei Shan Site II Tel: 886-2-2601-1640 Tel: 886-3-271-8666 Tel: 886-3-271-8640 No.30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, Taiwan (R.O.C.) No.3-1, Lane 6, Wen San 3rd St., Kwei Shan Dist., Tao Yuan City 33381, Taiwan (R.O.C.) No.2-1, Lane 6, Wen San 3rd St., Kwei Shan Dist., Tao Yuan City 33381, Taiwan (R.O.C.) No.14-1, Lane 19, Wen San 3rd St., Kwei Shan Dist., Tao Yuan City 33381, Taiwan (R.O.C.) If you have any suggestion, please feel free to contact us as below information. Tel: 886-3-271-8666 Fax: 886-3-318-0345 Email: [email protected] ══END══

Antenna Data Sheet Antenna Manufacturer Information: The antenna(s) for Garmin Model A0P3039 is manufactured by Raytac. 5F, No.3, Jiankang Rd., Zhonghe Dist., New Taipei City, 235, Taiwan Antenna Description: This data sheet contains the antenna gain information for the A0P3039-A1 for Garmin Model A0P3039. The approximate operational frequency band of these technologies is given, and the maximum gain within the frequency band is shown in Table 1. Table 1 Antenna Gain: Antenna Model Number Type Maximum Gain Approximate Frequency Band A0P3039-A1 chip -0.65 dBi 2400 to 2500 MHz NOTE: Antenna Gain is listed as N/A in the table when the specific antenna is only used for radios where the applicable rule parts are measured as a radiated field strength, and/or there are no rules pertaining to antenna gain limits. Additional Information: Contact Garmin for other information regarding antenna design, dimensions, cable length, etc.

Report No.: FR590201 Page : 1 of 17 Report Version: Rev. 01 FCC Test Report FCC ID : IPH-0P3039 Equipment : Outdoor Product Model No. : A0P3039 Brand Name : GARMIN Applicant : Garmin International, Inc. Address : 1200 E. 151st Street Olathe, KS 66062 United States Standard : 47 CFR FCC Part 15.247 Received Date : Sep. 02, 2025 Tested Date : Dec. 05 ~ Dec. 08, 2025 We, International Certification Corporation, would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It shall not be reproduced except in full without the written approval of our laboratory. Reviewed by: Approved by: Along Chen / Manager Gary Chang / Manager Report No.: FR590201 Page : 2 of 17 Report Version: Rev. 01 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 7 1.3 Test Setup Chart .................................................................................................................................... 7 1.4 Test Equipment List and Calibration Data .............................................................................................. 8 1.5 Test Standards ....................................................................................................................................... 9 1.6 Reference Guidance .............................................................................................................................. 9 1.7 Deviation from Test Standard and Measurement Procedure ................................................................. 9 1.8 Measurement Uncertainty ...................................................................................................................... 9 2 TEST CONFIGURATION ..................................................................................................................... 10 2.1 Testing Facility...................................................................................................................................... 10 2.2 The Worst Test Modes and Channel Details ....................................................................................... 10 3 TRANSMITTER TEST RESULTS ........................................................................................................ 11 3.1 6dB and Occupied Bandwidth .............................................................................................................. 11 3.2 Conducted Output Power ..................................................................................................................... 12 3.3 Power Spectral Density ........................................................................................................................ 13 3.4 Unwanted Emissions in Restricted Frequency Bands ......................................................................... 14 3.5 Emissions in non-restricted Frequency Bands ..................................................................................... 16 4 TEST LABORATORY INFORMATION ............................................................................................... 17 Appendix A. 6dB and Occupied Bandwidth Appendix B. Conducted Output Power Appendix C. Power Spectral Density Appendix D. Unwanted Emissions into Restricted Frequency Bands Appendix E. Emissions in Non-Restricted Frequency Bands Report No.: FR590201 Page : 3 of 17 Report Version: Rev. 01 Release Record Report No. Version Description Issued Date FR590201 Rev. 01 Initial issue Jan. 08, 2026 Report No.: FR590201 Page : 4 of 17 Report Version: Rev. 01 Summary of Test Results FCC Rules Test Items Measured Result 15.207 AC Power Line Conducted Emissions Note 1 N/A 15.247(d) 15.209 Unwanted Emissions [dBuV/m at 3m]: 12010.00MHz 50.89 (Margin -3.11dB) - AV Pass 15.247(b)(3) Conducted Output Power Power [dBm]: 7.49 Pass 15.247(a)(2) 6dB Bandwidth Meet the requirement of limit Pass 15.247(e) Power Spectral Density Meet the requirement of limit Pass 15.203 Antenna Requirement Meet the requirement of limit Pass N/A means Not Applicable. Note 1 : The EUT consumes DC power from battery, so the test is not required. Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. Report No.: FR590201 Page : 5 of 17 Report Version: Rev. 01 1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) RF General Information Frequency Range (MHz) Bluetooth Mode Ch. Freq. (MHz) Channel Number Data Rate 2400-2483.5 LE 2402-2480 0-39 [40] 1 Mbps 2 Mbps Note: Bluetooth LE (Low energy) uses GFSK modulation. 1.1.2 Antenna Details Brand Model Type Connector Gain (dBi) Remarks Raytac MDBT50Q CHIP No -0.65 -- 1.1.3 Power Supply Type of Equipment under Test (EUT) Power Supply Type 3Vdc from battery 1.1.4 Accessories Accessories No. Equipment Description 1 Battery Brand: Panasonic Model: CR15H270 Power Rating: 3Vdc, 850mAh Report No.: FR590201 Page : 6 of 17 Report Version: Rev. 01 1.1.5 Channel List Frequency band (MHz) 2400~2483.5 Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 37 2402 9 2422 18 2442 28 2462 0 2404 10 2424 19 2444 29 2464 1 2406 38 2426 20 2446 30 2466 2 2408…

Text truncated - open the document above for the full version.