JFZT3201ADE2Professional UHF band wireless microphone

3000 series Quick Start Guide / UHF Wireless System Guide de démarrage rapide / Système UHF sans fil Kurzanleitung / UHF-Drahtlossystem Guida rapida / Sistema wireless UHF Guía de inicio rápido / Sistema inalámbrico UHF Guia de início rápido / Sistema sem fio UHF Краткое руководство по установке / Беспроводная система УВЧ 快速启动指南 / UHF无线系统 快速入門指南 / UHF無線系統 간편 사용 설명서 / UHF 무선 시스템 クイックスタートガイド / UHFワイヤレスシステム English Important information Warning: To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. Caution: Do not expose this apparatus to drips or splashes. To avoid electric shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not expose this apparatus to excessive heat such as that generated by sunshine, fire or other heat sources. Do not subject this apparatus to strong impact. This apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time. In case of emergency, disconnect the AC adapter quickly. Do not place any objects filled with liquids, such as vases, on this apparatus. To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus. Do not install this apparatus in a confined space such as a bookcase or similar unit. Install this apparatus only in the places with good ventilation. The rating label is put on the bottom of this apparatus. Battery caution: Keep batteries out of the reach of children. Observe correct polarity as marked. Do not expose the battery to excessive heat such as sunshine, fire or the like. Always consider the environment issues and follow local regulations when disposing of batteries. Remove depleted battery immediately. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Use only disposable LR06(AA) alkaline or Ni-MH batteries. Do not use new batteries and old one at the same time. Do not use different batteries type or model. Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact occurs, immediately wash thoroughly with soap and water. If battery leakage comes into contact with your eyes, immediately flush with water and seek medical. For customers in the USA FCC Notice Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: − Reorient or relocate the receiving antenna. − Increase the separation between the equipment and receiver. − Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. − Consult the dealer or an experienced radio/TV technician for help. Contact: Responsible Company: Audio-Technica U.S., Inc. Address: 1221 Commerce Drive, Stow, Ohio 44224, USA Tel: 330-686-2600 For customers in Canada IC statement CAN RSS-Gen/CNR-Gen This device complies with INDUSTRY CANADA R.S.S. 210. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference which may cause undesired operation. This device complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. Français Informations importantes Avertissement: Pour éviter tout risque de choc électrique ou d’incendie, n’exposez pas cet appareil à la pluie ou à l’humidité. Attention: Protégez cet appareil des projections et des gouttes d’eau. Pour éviter tout risque de choc électrique, n’ouvrez pas le boîtier. Confiez tous travaux d’entretien à un technicien qualifié. N’exposez pas cet équipement à des températures excessives, telles que celles de la lumière directe du soleil, d’une flamme ou autres sources de chaleur. Ne soumettez pas cet équipement à de forts impacts. Cet appareil doit être placé à proximité de la prise secteur afin que vous puissiez facilement vous saisir de l'adaptateur secteur à tout moment. En cas d'urgence, débranchez l'adaptateur secteur au plus vite. Ne placez pas d’objets remplis de liquide tels que des vases, sur l’appareil. Pour éviter tout risque d’incendie, ne placez pas de flammes nues (telles que des bougies allumées) sur l’appareil. N’installez pas cet appareil dans un espace confiné tel qu’une étagère ou un endroit similaire. N'installez cet appareil que dans des endroits bien aérés. La plaque signalétique se trouve sur le dessous de cet appareil. Mise en garde relative aux piles: Tenez les piles hors de portée des enfants. Respectez la polarité correcte indiquée. N'exposez pas la pile à une chaleur excessive telle que les rayons du soleil, un feu ou autre source de chaleur. Prenez toujours en considération l'impact environnemental et suivez les réglementations locales lors de la mise au rebut des piles. Retirez immédiatement toute pile déchargée. Danger d'explosion en cas de positionnement incorrect de …

Text truncated - open the document above for the full version.

User Manual UHF Wireless Systems ATW-R3210 Receiver ATW-T3201 / ATW-T3201a Body-Pack Transmitter ATW-T3202 ATW-T3202a Handheld Transmitter 3000 Series 1 Contents Introduction .................................................................................2 Important information .................................................................2 Notes on use ...............................................................................3 Maintenance ................................................................................3 Part names and functions ............................................................4 ATW-R3210 .....................................................................................................4 ATW-T3201 / ATW-T3201a ...............................................................................6 ATW-T3202 / ATW-T3202a ...............................................................................7 How to insert batteries ................................................................8 ATW-T3201 / ATW-T3201a ...............................................................................8 ATW-T3202 / ATW-T3202a ...............................................................................8 How to attach and detach the interchangeable microphone capsule (only for ATW-T3202 /ATW-T3202a)................................9 How to attach .................................................................................................9 How to remove ...............................................................................................9 How to read the display ............................................................10 ATW-R3210 ...................................................................................................10 ATW-T3201 / ATW-T3201a / ATW-T3202 / ATW-T3202a ................................12 How to operate ..........................................................................13 Basic operation .............................................................................................13 Using IR SYNC ..............................................................................................13 Settings .....................................................................................14 ATW-R3210 ...................................................................................................14 ATW-T3201 / ATW-T3201a / ATW-T3202 / ATW-T3202a ................................14 Setting ATW-R3210 ...................................................................15 List of setting items ......................................................................................15 Setting the operating frequency ..................................................................15 Setting the channel (receiver) name .............................................................15 Setting the audio output level .......................................................................16 Scanning for open channels .........................................................................16 Setting transmitters via IR SYNC .................................................................16 Setting the squelch level ...............................................................................17 Setting the system-related functions ............................................................17 Setting ATW-T3201 / ATW-T3201a / ATW-T3202 / ATW-T3202a ... 20 List of setting items ......................................................................................20 Setting the transmission frequency ..............................................................20 Setting the channel (transmitter) name ........................................................20 Setting ATW-T3201 / ATW-T3201a / ATW-T3202 / ATW-T3202a ... 21 Adjusting the gain .........................................................................................21 Setting the RF power ....................................................................................21 Setting HPF (High-Pass Filter) .......................................................................21 Setting lock ...................................................................................................21 Setting the function for the function button .................................................21 Setting ATW-T3201 / ATW-T3201a / ATW-T3202 / ATW-T3202a ... 22 Setting the mute mode (only for ATW-T3201 / ATW-T3202a) .......................22 Setting the system-related functions ............................................................22 How to attach the transmitter (ATW-T3201 / ATW-T3201a) ......24 Making connections (basic connections) ..................................24 Achieving stable reception ........................................................25 Rack-mounting the receiver.......................................................25 Troubleshooting .........................................................................26 ATW-R3210 ...................................................................................................26 ATW-T3201 / ATW-T3201a / ATW-T3202 / ATW-T3202a ................................26 Dimensions ................................................................................27 ATW-R3210 ...................................................................................................27 ATW-T3201 / ATW-T3201a .............................................................................28 ATW-T3202 / ATW-T3202a .............................................................................28 Specifications ............................................................................29 Overall system specifications........................................................................29 ATW-R3210 ...................................................................................................29 ATW-T3201 / ATW-T3201a .........................................…

Text truncated - open the document above for the full version.

Annex A 1-5411/20-01-01_AnnexA External photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Hans-Joachim Wolsdorfer Lab Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2023-01-10Document No. 1-5411/20-01-01_AnnexA2/8 Photo 3 Photo 4 2023-01-10Document No. 1-5411/20-01-01_AnnexA3/8 Photo 5 Photo 6 2023-01-10Document No. 1-5411/20-01-01_AnnexA4/8 Photo 7 Photo 8 2023-01-10Document No. 1-5411/20-01-01_AnnexA5/8 Photo 9 Photo 10 2023-01-10Document No. 1-5411/20-01-01_AnnexA6/8 Photo 11 Photo 12 2023-01-10Document No. 1-5411/20-01-01_AnnexA7/8 Document history VersionApplied changesDate of release initial release2023-01-10 - END OF DOCUMENT - 2023-01-10Document No. 1-5411/20-01-01_AnnexA8/8

MODEL : ATW - T3201aDE2 FREQ. : 47 0 -530 MHz BATT. : LR6, AA×2, 3 V FCC ID : JF ZT3201ADE2 IC : 1752B-T3201ADE2 Audio -Technica Corporati on MADE IN CHINA ANATEL : 18768-20-03529 Size: W27.8×H26.8 mm ATW-T3201aDE2 470-530 MHz RATING LABEL P#2347-00600 2022.08.02 K Color **************

㼙㼛㼐㼑㼘㻌㼚㼍㼙㼑 㻯㻱㻘㼁㻷㻯㻭 㻲㻯㻯㻘㻵㻯 $ * ) ( ' & %  ὀグ $7ࢢ࣮ࣝࣉ〇ရ⎔ቃရ(休)ᇶ‽࡟㐺ྜ࡜ࡇࡿࡍ 127( &RPSO\ZLWKWKH$XGLR7HFKQLFD*URXSHQYLURPHQWDOTXDOLW\VWDQGDUGIRUSURGXFWV '(6&5,37,21 ,668(1R '$7( 1$0( 5(9 RYHUXSWR RYHUXSWR RYHUXSWR RYHUXSWR XSWR 3HUPLVVLEOHGHYLDWLRQV RIEDVLFVL]HUDQJH>PP@ 7ROHUDQFHFODVV s s s s ss ss ss ss ss s 7ROHUDQFHVIRUEURNHQHGJHVDQGDQJXODUGLPHQVLRQV-,6%P FRDUFHPHGLXPILQH  0$7(5,$/ '(6,*1(''5$:1&+(&.('$33529('6&$/( \BKRVKLQR 02'(/1$0(3$571$0( 3&2'( ),1,6+ 6800$5< 6,=(2)0$7(5,$/ $(4('<(1F $7:7  $7:7F

Annex B 1-5411_22-01-01_AnnexB Internal photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Hans-Joachim Wolsdorfer Lab Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2023-01-11Document No. 1-5411_22-01-01_AnnexB2/6 Photo 3 Photo 4 2023-01-11Document No. 1-5411_22-01-01_AnnexB3/6 Photo 5 Photo 6 2023-01-11Document No. 1-5411_22-01-01_AnnexB4/6 Photo 7 Photo 8 2023-01-11Document No. 1-5411_22-01-01_AnnexB5/6 Document history VersionApplied changesDate of release initial release2023-01-11 - END OF DOCUMENT - 2023-01-11Document No. 1-5411_22-01-01_AnnexB6/6

Test report No. : 14351608H-A Page : 1 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 SAR TEST REPORT Test Report No.: 14351608H-A Customer Audio-Technica Corporation Description of EUT Body-pack Transmitter Model Number of EUT ATW-T3201aDE2 FCC ID JFZT3201ADE2 Test Regulation FCC47CFR 2.1093 Test Result Complied (Refer to SECTION 4) Issue Date October 4, 2022 Remarks The highest reported SAR (1 g) Standalone Tx (Body-worn) : 0.19 W/kg Representative Test Engineer Approved By Hisayoshi Sato Engineer Satofumi Matsuyama Engineer CERTIFICATE 5107.02 The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan, Inc. There is no testing item of "Non-accreditation". Re port Cover Page - Form-ULID-003532 (DCS:13-EM-F0429) Issue# 21.0 Test report No. : 14351608H-A Page : 2 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 ANNOUNCEMENT REVISION HISTORY Original Test Report No.: 14351608H-A Revision Test report No. Date Page Revised Contents - (Ori ginal) 14351608H-A October 4, 2022 - • This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. • The results in this report appl y only to the sample tested. • This sample tested is in compliance with the limits of the above re gulation. • The test results in this test report are traceable to the national or international standards. • This test report must not be used by the customer to claim product certification, approval, or endorsement by the A2LA accreditation bod y. • This test report covers SAR technical requirements. It does not cover administrative issues such as Manual or non-SAR test related Requirements. (if applicable) • The all test items in this test report are conducted b y UL Japan, Inc Ise EMC Lab. • The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan, Inc. has been accredited. • The information provided from the customer for this report is identified in Section 1. • For test report(s) referred in this report, the latest version (includin g any revisions) is always referred. Test report No. : 14351608H-A Page : 3 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 Reference: Abbreviations (Including words undescribed in this report) AAN Asymmetric Artificial Network GPS Global Positioning System AC Alternating Current Hori. Horizontal AM Amplitude Modulation ICES Interference-Causing Equipment Standard AMN Artificial Mains Network I/O Input/Output Amp, AMP Amplifier IEC International Electrotechnical Commission ANSI American National Standards Institute IEEE Institute of Electrical and Electronics Engineers Ant, ANT Antenna IF Intermediate Frequency AP Access Point ILAC International Laboratory Accreditation Conference ASK Amplitude Shift Keying ISED Innovation, Science and Economic Development Canada Atten., ATT Attenuator ISN Impedance Stabilization Network AV Average ISO International Organization for Standardization BPSK Binary Phase-Shift Keying JAB Japan Accreditation Board BR Bluetooth Basic Rate LAN Local Area Network BT Bluetooth LCL Longitudinal Conversion Loss BT LE Bluetooth Low Energy LIMS Laboratory Information Management System BW BandWidth LISN Line Impedance Stabilization Network C.F Correction Factor MRA Mutual Recognition Arrangement Cal Int Calibration Interval N/A Not Applicable CAV CISPR AV NIST National Institute of Standards and Technology CCK Complementary Code Keying NS No signal detect. CDN Coupling Decoupling Network NSA Normalized Site Attenuation Ch., CH Channel OBW Occupied BandWidth CISPR Comite International Special des Perturbations Radioelectriques OFDM Orthogonal Frequency Division Multiplexing Corr. Correction PER Packet Error Rate CPE Customer premise equipment PK Peak CW Continuous Wave P LT long-term flicker severity DBPSK Differential BPSK POHC(A) Partial Odd Harmonic Current DC Direct Current Pol., Pola. Polarization DET Detector PR-ASK Phase Reversal ASK D-factor Distance factor P ST short-term flicker severity Dmax maximum absolute voltage change during an observation period QAM Quadrature Amplitude Modulation DQPSK Differential QPSK QP Quasi-Peak DSSS Direct Sequence Spread Spectrum QPSK Quadrature Phase Shift Keying DUT Device Under Test r.m.s., RMS Root Mean Square EDR Enhanced Data Rate RBW Resolution BandWidth e.i.r.p., EIRP Equivalent Isotropically Radiated Power RE Radio Equipment EM clamp Electromagnetic clamp REV Reverse EMC ElectroMagnetic Compatibility RF Radio Frequency EMI ElectroMagnetic Interference RFID Radio Frequency Identifier EMS ElectroMagnetic Susceptibility RNSS Radio Navigation Satellite Service EN European Norm RSS Radio Standards Specifications e.r.p., ERP Effective Radiated Power Rx Receiving ETSI European Telecommunications Standards Institute SINAD Ratio of (Signal + Noise + Distortion) to (Noise + Distortion) EU European Union S/N Signal to Noise ratio EUT Equipment Under Test SA, S/A Spectrum Analyzer Fac. Factor SG Signal Generator FCC Federal Communications Commission SVSWR Site-Voltage Standing Wave Ratio FHSS Frequency Hopping Spread Spectrum THC(A) Total Harmonic Current FM Frequency Modulation THD(%) Total Harmonic Distortion Freq. Frequency TR, T/R Test Receiver FSK Frequency Shift Keying Tx Transmitting Fund Fundamental VBW Video BandWidth FWD Forward Vert. Vertical GFSK Gaussian Frequency-Shift Keying WLAN Wireless LAN GNSS Global Navigation Satellite System xDSL Generic term for all types of DSL technology (DSL: Digital Subscriber Line) Test report No. : 14351608H-A Page : 4 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 CONTENTS PAGE SECTION 1: Customer information .................................................................................................. 5 SECTION 2: Equ…

Text truncated - open the document above for the full version.

TEST REPORT Test report no.: 1-5411_22-01-0 2 Testing laboratory Applicant CTC advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://www.ctcadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate starting with the registration number: D-PL-12076-01. Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida 194-8666 Tokyo / JAPAN Phone: +81-42-739-9121 Contact: Fumio Kamimura e-mail: [email protected] Manufacturer Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida 194-8666 Tokyo / JAPAN Test standard/s FCC - Title 47 CFR Part 74 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 74 - Experimental radio, auxiliary, special broadcast and other program distributional services RSS - 210 Issue 10 Spectrum Management and Telecommunications Radio Standards Specification - Licence-Exempt Radio Apparatus: Category I Equipment For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: Professional UHF band wireless microphone Model name: ATW-T3201aDE2 FCC ID: JFZT3201ADE2 ISED certification number: 1752B-T3201ADE2 Frequency: 470.125MHz – 529.975MHz Technology tested: proprietary Antenna: external whip antenna Power supply: 2.4 V to 3.2 V DC Temperature range: -5°C to +45°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: Christoph Schneider Hans-Joachim Wolsdorfer Lab Manager Lab Manager Radio Communications Radio Communications Test report no.: 1-5411_22-01-02 © CTC advanced GmbH Page 2 of 34 1 Table of contents 1 Table of contents ............................................................................................................................................. 2 2 General information ......................................................................................................................................... 3 2.1 Notes and disclaimer ............................................................................................................................ 3 2.2 Application details ................................................................................................................................ 3 2.3 Test laboratories sub-contracted ......................................................................................................... 3 3 Test standard/s, references and accreditations .............................................................................................. 4 4 Reporting statements of conformity – decision rule ...................................................................................... 5 5 Test environment ............................................................................................................................................. 6 6 Test item........................................................................................................................................................... 6 6.1 General description ............................................................................................................................... 6 6.2 Additional information .......................................................................................................................... 6 7 Description of the test setup ............................................................................................................................ 7 7.1 Shielded fully anechoic chamber .......................................................................................................... 8 7.2 Conducted measurements normal and extreme conditions ................................................................. 9 8 Sequence of testing ....................................................................................................................................... 10 8.1 Sequence of testing radiated spurious 30MHz to 12.75GHz ............................................................. 10 9 Measurement uncertainty .............................................................................................................................. 11 10 Summary of measurement results ......................................................................................................... 12 11 Additional comments .............................................................................................................................. 13 12 Measurement results .............................................................................................................................. 14 12.1 Transmitter output power ................................................................................................................ 14 12.2 Occupied bandwidth ........................................................................................................................ 17 12.3 Transmitter frequency stability ....................................................................................................... 20 12.4 Transmitter unwanted emissions (radiated) ................................................................................... 21 12.5 Modulation characteristics .............................................................................................................. 24 12.6 Necessary bandwidth (BN) for analogue systems .......................................................................... 25 12.7 Frequency modulation ..................................................…

Text truncated - open the document above for the full version.

Test report No. : 14351608H-A Page : 61 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 APPENDIX 4: Photographs of test setup Photographs of EUT Photograph A1: Front Photograph A4: Rear Photograph A3: Top Photograph A5: Left Photograph A2: Right Test report No. : 14351608H-A Page : 62 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 Antenna position 81 mm Antenna ↑Bottom Photograph B1: With microphone Photograph C1: Antenna position Test report No. : 14351608H-A Page : 63 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 Photographs of setup Photo graph D1: Body, Front, 0mm (Front view) Photograph D3: Body, Rear, 0mm (Front view) Photograph D2: Body, Front, 0mm (Side view) Photograph D4: Body, Rear, 0mm (Side view) Test report No. : 14351608H-A Page : 64 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 Photo graph D5: Body, Right, 0mm (Front view) Photograph D7: Body, Left, 0mm (Front view)* * Microphone is removed for flat phantom contact with microphone Photograph D6: Body, Right, 0mm (Side view) Photograph D8: Body, Left, 0mm (Side view) Test report No. : 14351608H-A Page : 65 of 65 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 Japan / +81-596-24-8999 Photo graph D9: Body, Top, 0mm (Front view) Photograph D10: Body, Top, 0mm (Side view) End of Report

Annex D No.1-5411_22-01-01_AnnexD Setup photos of the Device Under Test This document is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Hans-Joachim Wolsdorfer Lab Manager Radio Communications CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Annex D Photo 1 Photo 2 2023-01-10 Document 1-5411_22-01-01_AnnexD 2/4 Photo 3 Photo 4 2023-01-10 Document 1-5411_22-01-01_AnnexD 3/4 Photo 5 - END OF DOCUMENT - 2023-01-10 Document 1-5411_22-01-01_AnnexD 4/4