JKD4100CAR ALARM TRANSMITTER

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.

Huge Technology Co., LTD.. FCC ID.: JKD4100 6F-8., No.20, Lane 609, Chung-Hsin Rd., Sec. 5, San-Chung City, Taipei, Taiwan, R.O.C. Tel: 886 2 2999 1714 FCC ID The FCC ID will be placed on the equipment as shown in the photograph below. Car Alarm Transmitter Model No.: TC-4100 TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan Car Alarm Transmitter Model No.: TC-4100 F F C C C C I I D D : : J J K K D D 4 4 1 1 00 S/N: Made in Taiwan

Huge Technology Co., LTD.. FCC ID.: JKD4100 6F-8., No.20, Lane 609, Chung-Hsin Rd., Sec. 5, San-Chung City, Taipei, Taiwan, R.O.C. Tel: 886 2 2999 1714 FCC ID The FCC ID will be placed on the equipment as shown in the photograph below. Car Alarm Transmitter Model No.: TC-4100 TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan Car Alarm Transmitter Model No.: TC-4100 F F C C C C I I D D : : J J K K D D 4 4 1 1 00 S/N: Made in Taiwan

Report No.: 039L510FI Page : 10 of 11 Version:1.0 (18) EUT Photo (19) EUT Photo Report No.: 039L510FI Page : 11 of 11 Version:1.0 (20) EUT Photo (21) EUT Photo

Report No. 039L510FI Page : 5 of 36 Version:1.0 1.2. Operation Description The EUT is a 303.5~330MHz transmitter. The radio remote control signal can be transferred to 308.9~309.3MHz radio frequency in GFSK modulation. The transmission antenna is printed on the EUT. The radio remote control signal can be control the car alarm system.

Report No. 039L510FI Page : 1 of 36 Version:1.0 Test Report Product Name : Car Alarm Transmitter Model No. : TC-4100 FCC ID : JKD4100 Applicant : Huge Technology Co., LTD. Address : 6F-8., No. 20, Lane 609, Chung-Hsin Rd., Sec.5, San-Chung City, Taipei, Taiwan. Date of Receipt : Sep. 09, 2003 Date of Test : Sep. 17, 2003 Report No. : 039L510FI The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 039L510FI Page : 2 of 36 Version:1.0 Test Report Certification Test Date : Sep. 17, 2003 Report No. : 039L510FI Product Name : Car Alarm Transmitter Applicant : Huge Technology Co., LTD. Address : 6F-8., No. 20, Lane 609, Chung-Hsin Rd., Sec.5, San-Chung City, Taipei, Taiwan. Manufacturer : Huge Technology Co., LTD. Ningbo Poly Technology Co., Ltd. Model No. : TC-4100 FCC ID. : JKD4100 Rated Voltage : DC 12V Trade Name : TOPE Measurement Standard : FCC Part 15 Subpart C Paragraph 15.231 Measurement Procedure : ANSI C63.4:1992 Test Result : Complied The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Documented By : (Anita Chou ) Tested By : (Tom Hsieh ) Approved By : (Gene Chang ) Accredited by NIST (NVLAP) NVLAP Lab Code: 200347-0 Report No. 039L510FI Page : 3 of 36 Version:1.0 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION..............................................................................................................4 1.1. EUT Description ....................................................................................................................................4 1.2. Operation Description ............................................................................................................................5 1.3. Tested System Details ............................................................................................................................6 1.4. Configuration of Tested System .............................................................................................................6 1.5. EUT Exercise Software..........................................................................................................................6 1.6. Test Facility ............................................................................................................................................7 2. Conducted Emission ............................................................................................................................8 2.1. Test Equipment ......................................................................................................................................8 2.2. Test Setup ...............................................................................................................................................8 2.3. Limits .....................................................................................................................................................8 2.4. Test Procedure ........................................................................................................................................9 2.5. Test Result of Conducted Emission .....................................................................................................10 3. Radiated Emission.............................................................................................................................. 11 3.1. Test Equipment ....................................................................................................................................11 3.2. Test Setup .............................................................................................................................................11 3.3. Limits ...................................................................................................................................................12 3.4. Test Procedure ......................................................................................................................................13 3.5. Test Result of Radiated Emission ........................................................................................................14 4. Occupied Bandwidth..........................................................................................................................24 4.1. Test Equipment ....................................................................................................................................24 4.2. Test Setup .............................................................................................................................................24 4.3. Limits ...................................................................................................................................................24 4.4. Test Result of Occupied Bandwidth.....................................................................................................25 5. Duty Cycle...........................................................................................................................................29 5.1. Test Equipment ....................................................................................................................................29 5.2. Test Setup .............................................................................................................................................29 5.3. Test Result of Duty Cycle ....................................................................................................................30 6. EMI Reduction Method During Compliance Testing ..…

Text truncated - open the document above for the full version.

Report No.: 039L510FI Page : 1 of 2 Version:1.0 Attachment 1: EUT Test Setup Photographs Front View of Radiated Test Back View of Radiated Test Report No.: 039L510FI Page : 2 of 2 Version:1.0 Front View of Radiated Test (Horn)