JNZAR0209Wireless Headphones

LOGITECH FAR EAST LTD. #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu, Taiwan, R.O.C. Declaration letter Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Declaration letter for label requirement Date: 2026-01-15 FCC ID: JNZAR0209 The label is permanently affixed on the SPK plastic surface beneath the ear cushion. The ear cushions can be easily removed without any special tools, and the FCC ID will also be printed on the packaging when sold on the market. End-users will be able to see the FCC ID directly on the packaging. Please don’t hesitate to contact us if you have any questions. Thank you! ----------------------------------- David W Crawford / Senior manager, Compliance Engineering LOGITECH FAR EAST LTD. Tel: +1-360-817-1253 E-mail: [email protected]

Date: [1/15/2026] FCC ID: JNZAR0209 To the attention of Federal Communications Commission Authorization and Evaluation Division Attestation Statements Attestation Statements Part 2.911(d)(5)(i) Filing LOGITECH FAR EAST LTD. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Attestation Statements Part 2.911(d)(5)(ii) Filing LOGITECH FAR EAST LTD. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely yours, ----------------------------------------------- David W Crawford / Senior Manager, Compliance Engineering LOGITECH FAR EAST LTD. Tel: +1-360-817-1253 E-mail: [email protected]

Date: 1/15/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) FCC US Agent Letter of Attestation FCC ID: JNZAR0209 To whom it may concern: FCC US Agent Agent Company Name: Logitech, Inc. FCC FRN: 0005921077 Agent Contact Name: David W Crawford Agent US Address: 4700 NW Camas Meadows Drive, Camas, WA 98607 Agent Email Address: [email protected] This letter is to confirm that we have accepted the responsibility to act as US Agent on behalf of Logitech Far East, Ltd. (“the applicant”) for the above referenced FCC ID. We are aware of the requirements and responsibilities of the applicant’s agent for service of process as outlined in the FCC section 2.911(d)(7) and Report and Order FCC 22-84 paragraph 63. Sincerely, David W Crawford Senior Manager, Compliance Engineering Logitech, Inc.

Date: 1/15/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation FCC ID: JNZAR0209 Applicant (Grantee) FRN: 0007134034 Logitech Far East, Ltd., (“the applicant”) as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicant’s agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. U.S. Agent Information: Contact Person: David W Crawford Company Name: Logitech, Inc. Company Address: 4700 NW Camas Meadows Drive, Camas, WA 98607 Email: [email protected] FCC FRN: 0005921077 Sincerely yours, Name: Rick Lien Job Title: Head of Product Compliance Company Name: Logitech Far East, Ltd. Email: [email protected] Tel: +886-3-5778241 #2189

#2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. To the attention of Federal Communications Commission Authorization and Evaluation Division Date: 2026-01-15 FCC ID: JNZAR0209 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application asoutlined below: Schematics Diagram Block Diagram Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Internal Photos Test Setup photos User’s manual The Applicant understands that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely yours, ----------------------------------- David W Crawford/ Senior Manager, Compliance Engineering LOGITECH FAR EAST LTD. Tel: +1-360-817-1253 E-mail: [email protected]

LOGITECH FAR EAST LTD. #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Date: 2026-01-15 FCC ID: JNZAR0209 AUTHORIZATION LETTER To W h o m I t M a y C o n c e r n : LOGITECH FAR EAST LTD. hereby authorizes Andrea Hsia / Assistant Manager of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Assistant Manager of BV CPS Taoyuan on LOGITECH FAR EAST LTD.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------- David W Crawford / Senior Manager, Compliance Engineering Logitech, Inc. Tel: +1-360-817-1253 E-mail: [email protected]

FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Note: The FCC and ISED ID label will be on plastic surface underneath ear cushion.

SAR Test Report Report Format Version 8.0.0 Page No. : 1 of 25 Report No. : SFBDKG-WTW-P25110219 Issued Date : Jan. 21, 2026 SAR Test Report FCC Rule Part : CFR §2.1093 Standards : IEEE Std 1528:2013, KDB 865664 D01 v01r04, KDB 865664 D02 v01r02, KDB 447498 D04 Interim General RF Exposure Guidance v01 Report No. : SFBDKG-WTW-P25110219 Applicant : Logitech Far East Ltd Address : #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Product : Wireless Headphones FCC ID : JNZAR0209 Brand : Logitech Model No. : AR0209 Sample Received Date : Dec. 05, 2025 Date of Testing : Jan. 09, 2026 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan FCC Accredited No. : TW0003 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Gina Liu / Specialist Approved By : Gordon Lin / Manager This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. SAR Test Report Report Format Version 8.0.0 Page No. : 2 of 25 Report No. : SFBDKG-WTW-P25110219 Issued Date : Jan. 21, 2026 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Test Reference Guidance ...................................................................................................................................................... 4 2. Summary of Maximum SAR Value ....................................................................................................................................... 5 3. Description of Equipment Under Test ................................................................................................................................. 6 4. SAR Measurement System ................................................................................................................................................... 7 4.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 7 4.2 SPEAG DASY6 System ............................................................................................................................................... 7 4.1.1 Robot ............................................................................................................................................................... 8 4.1.2 Probes ............................................................................................................................................................. 9 4.1.3 Data Acquisition Electronics (DAE) .................................................................................................................. 9 4.1.4 Phantoms ......................................................................................................................................................... 9 4.1.5 Device Holder ................................................................................................................................................ 10 4.1.6 System Validation Dipoles ............................................................................................................................. 11 4.1.7 Power Source ................................................................................................................................................ 11 4.1.8 Tissue Simulating Liquids .............................................................................................................................. 12 4.3 SAR System Verification ..........................................................................................................................................…

Text truncated - open the document above for the full version.

Plots of System Verification Appendix A. Plots of System Verification The plots for system verification are shown as follows. Report No.: SFBDKG-WTW-P25110219 Plots of System Verification Measurement Report S01 System Check_H2450_260109 Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, 10.0 x 10.0 x 290.0 Dipole Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, , CW, 0-- 2450.000, 0 7.14 1.8 39.1 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - 1988 H19T27N5 , 2026-Jan-09 EX3DV4 - SN7696, 2025-09-11 DAE4 Sn1590, 2025-08-13 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 48.0 x 96.0 35.0 x 35.0 x 30.0 Grid Steps [mm] 12.0 x 12.0 5.0 x 5.0 x 1.5 Sensor Surface [mm] 3.0 1.4 Measurement Results Area Scan Zoom Scan Date 2026-01-09 2026-01-09 psSAR1g [W/kg] 2.56 2.62 psSAR10g [W/kg] 1.22 1.29 Power Drift [dB] 0.05 0.01 Report No.: SFBDKG-WTW-P25110219 Plots of Measurement Appendix B. Plots of Measurement The SAR plots for highest measured SAR in each exposure configuration, wireless mode and frequency band combination are shown as follows. Report No.: SFBDKG-WTW-P25110219 Plots of Measurement Measurement Report P01 BT_LE-2M_Left Ear_0mm_Ch19_Ant 0 Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type P25110219, 95.0 x 73.0 x 37.0 Headset Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, Left Ear, 0.00 ISM 2.4 GHz Band Bluetooth, 10670-AAA 2440.000, 19 7.14 1.79 39.1 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - 1988 H19T27N5 , 2026-Jan-09 EX3DV4 - SN7696, 2025-09-11 DAE4 Sn1590, 2025-08-13 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 120.0 x 144.0 30.0 x 30.0 x 30.0 Grid Steps [mm] 12.0 x 12.0 5.0 x 5.0 x 5.0 Sensor Surface [mm] 3.0 1.4 Measurement Results Area Scan Zoom Scan Date 2026-01-09 2026-01-09 psSAR1g [W/kg] 0.050 0.053 psSAR10g [W/kg] 0.026 0.027 Power Drift [dB] -0.06 -0.16 M2/M1 [%] 54.6 Dist 3dB Peak [mm] 11.1 Report No.: SFBDKG-WTW-P25110219 Appendix C. Tissue & System Verification The measuring results for tissue simulating liquid and system check are shown as below. Note: 1. For Section 4.3, the dielectric properties of the tissue simulating liquid have been measured within 24 hours before the SAR testing and within ±10 % of the target values. Liquid temperature during the SAR testing has kept within ±2 °C. 2. For Section 4.4, The SAR measurement system was validated according to procedures in FCC KDB 865664 D0. The validation status in tabulated summary is as below. 3. For Section 4.5, Comparing to the reference SAR value provided by SPEAG in dipole calibration certificate, the deviation of system check results is within its specification of 10 %. The result indicates the system check can meet the variation criterion and the plots please refer to Appendix A of this report. Report No.: SFBDKG-WTW-P25110219 Plot No. Frequency (MHz) LiquidTemp. (°C) Conductivity (σ) Permittivity (εr) Targeted Conductivity (σ) Targeted Permittivity (εr) Deviation Conductivity (σ) Deviation Permittivity (εr) Sensitivity Range Probe Linearity Probe Isotropy Modulation Type Duty Factor PAR Date Frequency (MHz) Targeted 1g SAR (W/kg) Measured 1g SAR (W/kg) Normalized 1g SAR (W/kg) Deviation (%) Dipole S/N Probe S/N DAE S/N Output Power (dBm) S01 2450 22.5 1.8 39.1 1.8 39.2 0.00 -0.26 Pass Pass Pass GFSK N/A Pass Jan. 09, 2026 2450 52.90 2.62 52.28 -1.18 737 7696 1590 17 Tissue Verification Validation for CW Validation for Modulation System Check Note Report No.: SFBDKG-WTW-P25110219 Appendix D. Maximum Target Conducted Power The maximum conducted average power (Unit: dBm) including tune-up tolerance is shown as below. Report No.: SFBDKG-WTW-P25110219 Tune-up Power (Full) ModeChannel Frequency Ant 0 Max Tune-up 024029.0 3924419.0 7824809.0 024029.0 3924419.0 7824809.0 024029.0 1924409.0 3924809.0 124049.0 1924409.0 3824789.0 LE-1M LE-2M GFSK 8DPSK Bluetooth Report No.: SFBDKG-WTW-P25110219 Appendix E. Measured Conducted Power Result The measuring conducted power (Unit: dBm) are shown as below. Report No.: SFBDKG-WTW-P25110219 Conducted Power (Full) ModeChannel Frequency SISO Ant 0 Avg. Power 024027.98 3924418.11 7824805.8 024028.06 3924418.15 7824804.57 024028.67 1924408.74 3924808.7 124048.68 1924408.75 3824788.71 LE-1M LE-2M Bluetooth Ant 0 8DPSK GFSK Report No.: SFBDKG-WTW-P25110219 Note: 1. SAR testing for BT was performed on the maximum power mode. Appendix F. SAR Test Result SAR Results for Head Exposure Condition. Report No.: SFBDKG-WTW-P25110219 Plot No. Band Mode Test Position Separation Distance (mm) Channel Ant Stat us Duty Cyc le Crest Factor Max. Tune-up Power (dBm) Measured Conducted Power (dBm) Scaling Factor Power Drift (dB) Measured SAR-1g (W/kg) Scaled SAR-1g (W/kg) 1 BT LE-2M Left Ear 0 19 Ant 0 56.48 1.77 9.00 8.75 1.06 -0.16 0.053 0.10 BT LE-2M Left Ear 0 1 Ant 0 56.48 1.77 9.00 8.68 1.08 -0.02 0.052 0.10 BT LE-2M Left Ear 0 38 Ant 0 56.48 1.77 9.00 8.71 1.07 -0.12 0.049 0.09 - 1.00 - - 1 - - System & Position DUT Configuration Head SAR Test Result SAR Report No.: SFBDKG-WTW-P25110219 Appendix Z. Calibration Certificate for Probe and Dipole The SPEAG calibration certificates are shown as follows. Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P25110219 Report No.: SFBDKG-WTW-P…

Text truncated - open the document above for the full version.

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: ORBAYG-WTW-P25120494 Page: 1 of 17 Report Format Version 3.0.2 3D Antenna Measurement Summary Report REPORT NO.: ORBAYG-WTW-P25120494 MODEL NAME: HDT589 TESTED DATE: 2025.12.18 ISSUED DATE: 2025.12.23 APPLICANT : Merry Electronics Co., Ltd. ADDRESS : 22, Industrial Park 23rd Rd., Nantun Dist., Taichung City 408017, Taiwan (R.O.C.) ISSUED BY: Bureau Veritas Consumer Products Services (Hong Kong) Limited, Taoyuan Branch Mobile Communications Laboratory ADDRESS: No.19, Hwa Ya 2nd Rd., Kwei shan Dist., Taoyuan City, Taiwan (R.O.C) The client to claim product certification, approval, or endorsement by TAF, CTIA or any government agencies, should not use this report. Report No.: ORBAYG-WTW-P25120494 Page: 2 of 17 Report Format Version 3.0.2 RELEASE CONTROL RECORD REPORT NO. REASON FOR CHANGE DATE ISSUED ORBAYG-WTW-P25120494 Original release 2025.12.23 TABLE OF CONTENTS GENERAL INFORMATION ................................................................................................................................. 3 1. Te s t Methods ............................................................................................................................................... 4 2. Description of the anechoic chamber: ........................................................................................................ 4 3. Test Equipment List ..................................................................................................................................... 5 4. Measurement Uncertainty .......................................................................................................................... 5 5. Testing Setup Photograph .......................................................................................................................... 5 6. Antenna Radiation Performance ................................................................................................................ 5 7. 3D Antenna Patterns .................................................................................................................................. 6 APPENDIX. EUT photographs .......................................................................................................................... 6 Report No.: ORBAYG-WTW-P25120494 Page: 3 of 17 Report Format Version 3.0.2 GENERAL INFORMATION APPLICANT: Merry Electronics Co., Ltd. MANUFACTURER: Merry Electronics Co., Ltd. MODEL NAME: HDT589 ANTENNA MODEL NAME: 52TX5892000LZ-M ANTENNA TYPE: PIFA Antenna MEASUREMENT STATNDARD ANSI/IEEE Std 149 2021 TESTED BY : , DATE : 2025.12.23 Leo Chen / Engineer PREPARED BY : , DATE : 2025.12.23 Johnny Liu / Supervisor APPROVED BY : , DATE : 2025.12.23 Ken Chan / Manager Report No.: ORBAYG-WTW-P25120494 Page: 4 of 17 Report Format Version 3.0.2 1. Test Methods The Antenna Gain Test is performed according to The ANSI/IEEE Std 149 12.3.1 Antenna Gain (Small size (< 42cm) Linear Polarization Antennas), using a two-axis support device and one fixed measurement antenna. The EUT is positioned along the required MAPS centerline fixture holder. The EUT is then stepped between 0 and 180 degrees along the theta axis in 15-degree increments. At each theta position, the phi axis is stepped from 0-360 degrees in 15-degree increments. Data is recorded using the Network analyzer for both theta and phi polarizations at each position. Depending on the protocol, an appropriate filter is used in the EMQuest software to process the data. Upon completion of the test, test results (angular dependent EIRP) is calculated at each measurement point and the required value is automatically calculated. This test procedure is repeated for frequency and configuration as required. 2. Description of the anechoic chamber: Length: 7.32 m Width: 3.66 m Height: 3.51 m Network Analyzer Measurement Antenna EUT Phi axis Theta axis H V Report No.: ORBAYG-WTW-P25120494 Page: 5 of 17 Report Format Version 3.0.2 3. Test Equipment List TYPE OF EQUIPMENT MODEL NUMBER SERIAL NUMBER CALIBRATION DUE DAT E (OTA3-HY) ETS Anechoic Chamber ETS-Lindgren AMS-8500 CT0000411-1132 N/A Measurement Software ETS-Lindgren EMQuest V1.14 build 31654 1281 N/A Multi-Axis Positioning System ETS-Lindgren 2090-OPTI 00086248 N/A Switch Control Agilent 3499A MY42005285 N/A Network Analyzer Agilent E5071C MY46104190 2026/7/10 4. Measurement Uncertainty Expanded Uncer…

Text truncated - open the document above for the full version.

Report No.: RFBDKG-WTW-P25110219-1 Page No. 1 / 48 Report Format Version: 7.2.0 Reference No.: BDKG-WTW-P25110219 TEST REPORT CERTIFICATE OF CONFORMITY Standard: 47 CFR FCC Part 15, Subpart C (Section 15.247) Report No.: RFBDKG-WTW-P25110219-1 FCC ID: JNZAR0209 Product: Wireless Headphones Brand: Logitech Model No.: AR0209 Received Date: 2025/12/5 Test Date: 2025/12/10 ~ 2025/12/18 Issued Date: 2026/1/21 Applicant: Logitech Far East Ltd Address: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 Approved by: , Date: 2026/1/21 Wen Yu / Assistant Manager This test report consists of 48 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Prepared by : Phoenix Huang / Specialist This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBDKG-WTW-P25110219-1 Page No. 2 / 48 Report Format Version: 7.2.0 Reference No.: BDKG-WTW-P25110219 Table of Contents Release Control Record ....................................................................................................................................................... 4 1 Certificate .................................................................................................................................................................... 5 2 Summary of Test Results .......................................................................................................................................... 6 2.1 Measurement Uncertainty ........................................................................................................................................ 6 2.2 Supplementary Information ...................................................................................................................................... 6 3 General Information ................................................................................................................................................... 7 3.1 General Description .................................................................................................................................................. 7 3.2 Antenna Description of EUT ..................................................................................................................................... 8 3.3 Channel List .............................................................................................................................................................. 9 3.4 Test Mode Applicability and Tested Channel Detail ................................................................................................ 10 3.5 Duty Cycle of Test Signal........................................................................................................................................ 11 3.6 Test Program Used and Operation Descriptions .................................................................................................... 12 3.7 Connection Diagram of EUT and Peripheral Devices ............................................................................................ 12 3.8 Configuration of Peripheral Devices and Cable Connections ................................................................................ 13 4 Test Instruments ...................................................…

Text truncated - open the document above for the full version.