JNZMR00522.4GHz Cordless Mouse

Logitech® Important Information Safety, Regulatory, and Warranty English Additional compliance information: http://www.logitech.com/compliance. UL Statement: Your product is UL approved. Use only with UL listed ITE computers. FCC United States and IC-Canada This hardware device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Compliance Information Statements: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. Modifications to this product not authorized by Logitech could void your right to use or operate this product by the FCC. Where shielded interface cables or accessories have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations. IC-Canada Statements: Corded products: This Class B digital apparatus complies with Canadian ICES-003. Logitech hardware product limited warranty. Logitech warrants to the original purchaser that your Logitech hardware product shall be free from defects in material and workmanship for the period of time, identified on your product package and/or contained in the user documentation, from the date of purchase. You may also find this information by selecting your product in the Online Support section of our website at www.logitech.com/support. Except where prohibited by applicable law, This warranty is nontransferable and is limited to the original purchaser. This warranty gives you specific legal rights, and you may also have other rights that vary under local laws. Logitech's entire liability and your exclusive remedy for any breach of warranty shall be, at Logitech's option, (1) to repair or replace the hardware, or (2) to refund the price paid, provided that the hardware is returned to the point of purchase or such other place as Logitech may direct with a copy of the sales receipt or dated itemized receipt. Shipping and handling charges may apply, except where prohibited by applicable law. Logitech may, at its option, use new or refurbished or used parts in good working condition to repair or replace any hardware product. Any replacement hardware product will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer or for any additional period of time that may be applicable in your jurisdiction. This warranty does not cover problems or damage resulting from (1) accident, abuse, misapplication, or any unauthorized repair, modification or disassembly; (2) improper operation or maintenance, usage not in accordance with product instructions or connection to improper voltage supply; or (3) use of consumables, such as replacement batteries, not supplied by Logitech except where such restriction is prohibited by applicable law. How to obtain warranty support. Before submitting a warranty claim, we recommend you visit the support section at www.logitech.com/support for technical assistance. Valid warranty claims are generally processed through the point of purchase during the first thirty (30) days after purchase; however, this period of time may vary depending on where you purchased your product - please check with Logitech or the retailer where you purchased your product for details. Warranty claims that cannot be processed through the point of purchase and any other product related questions should be addressed directly to Logitech. The addresses and customer service contact information for Logitech can be found in the documentation accompanying your product and on the web at www.logitech.com/support. Limitation of liability. LOGITECH SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOSS OF PROFITS, REVENUE OR DATA (WHETHER DIRECT OR INDIRECT) OR COMMERCIAL LOSS FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON YOUR PRODUCT EVEN IF LOGITECH HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Duration of implied warranties. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THIS HARDWARE PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THE APPLICABLE LIMITED WARRANTY PERIOD FOR YOUR PRODUCT. Additional Rights. Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from State to State or by country or other jurisdiction. National Statutory Rights. Consumers have legal rights under a…

Text truncated - open the document above for the full version.

MASTER ™ WIRELESS MOUSE | SOURIS SANS FIL Logitech MX Master 2 English What’s in the box Logitech MX Master English 3 Mouse features 1. Scroll wheel 2. Manual switch button 3. Thumb wheel 4. Forward 5. Back 6. Thumb button 7. Micro USB connector 8. On/Off switch 9. Connect button 10. Easy­Switch button For much more: www.logitech.com/MXMaster 1 2 3 1 2 6 4 3 5 7 8 10 9 Logitech MX Master 4 English Battery disposal 123 Logitech MX Master English 5 Z855 M/N:C-U0007 CFT: RCPLOCU10-1356 CNC: C-8941 IC: 4418A-CU0007 FCC ID: JNZCU0007 CCAI10LP0020T1 DZL-C-U0007CMIIT ID: 2010DJ0355 2205-10-3229 ANATEL ( 01 ) 07898940473243 MODELO: C-U0007 M/N:C-U0008 IC: 4418A-CU0008 FCC ID: JNZCU0008 CFT: RCPLOCU11-0321 CNC: C-9341 CMIIT ID: 2011DJ1853 KCC-CRM-DZL-C-U0008 CCAI11LP0640T0 0899-11-3229 ANATEL ( 01 ) 7898940473489 MODELO: C-U0008 www.logitech.com/MXMaster © 2014 Logitech. All rights reserved. Logitech, the Logitech logo, and other Logitech marks are owned by Logitech and may be registered. Registered in the U.S. and other countries. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice. © 2014 Logitech. Tous droits réservés. Logitech, le logo Logitech et les autres marques Logitech sont la propriété de Logitech et sont susceptibles d’être déposés. Toutes les autres marques commerciales sont la propriété de leurs détenteurs respectifs. Logitech décline toute responsabilité en cas d’erreurs dans ce manuel. Les informations énoncées dans ce document peuvent faire l’objet de modifications sans avis préalable. 620-006452.002

Report No. : 141025E01 Page 1 CONSTRUCTION PHOTOS OF EUT Model : M-R0052 Report No. : 141025E01 Page 12

(Fig.1) FCC ID: JNZMR0052 FCC LABEL & Label LOCATION The label will be permanently affixed at a conspicuous location on the device.

Report No. : 141025E01 Page 2 Model : M-R0052 Report No. : 141025E01 Page 3 Report No. : 141025E01 Page 4 Report No. : 141025E01 Page 5 Report No. : 141025E01 Page 6 Report No. : 141025E01 Page 7 Report No. : 141025E01 Page 8 Report No. : 141025E01 Page 9 Report No. : 141025E01 Page 10 Report No. : 141025E01 Page 11

Report No.: SA141025E01 1 of 6 Report Format Version 5.0.1 RF EXPOSURE REPORT REPORT NO.: SA141025E01 MODEL NO.: M-R0052 FCC ID: JNZMR0052 RECEIVED: Oct. 25, 2014 TESTED: Oct. 31, 2014 ISSUED: Nov. 06, 2014 APPLICANT: LOGITECH FAR EAST LTD. ADDRESS: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA141025E01 2 of 6 Report Format Version 5.0.1 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. EVALUATION RESULT ........................................................................................... 5 2.1 SAR TEST EXCLUSION THRESHOLDS ................................................................ 5 Report No.: SA141025E01 3 of 6 Report Format Version 5.0.1 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA141025E01 Original release Nov. 06, 2014 Report No.: SA141025E01 5 of 6 Report Format Version 5.0.1 2. EVALUATION RESULT 2.1 SAR TEST EXCLUSION THRESHOLDS Following FCC KDB 447498 D01 “General RF Exposure Guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA141025E01 6 of 6 Report Format Version 5.0.1 Maximum measured transmitter power: BT-LE mode Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 10-g SAR test exclusion thresholds Result 2.402 ~ 2.480 2.061 5 0.649 7.5 Pass NOTE: 1. The antenna type is PCB printed antenna with 0.08dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. --- END ---

Report No.: RF141025E01-1 1 of 27 Report Format Version 5.0.1 FCC TEST REPORT (15.249, GFSK) REPORT NO.: RF141025E01-1 MODEL NO.: M-R0052 FCC ID: JNZMR0052 RECEIVED: Oct. 25, 2014 TESTED: Oct. 27 to 31, 2014 ISSUED: Nov. 06, 2014 APPLICANT: LOGITECH FAR EAST LTD. ADDRESS: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF141025E01-1 2 of 27 Report Format Version 5.0.1 Table of Contents RELEASE CONTROL RECORD ................................................................................. 3 1 CERTIFICATION ............................................................................................... 4 2 SUMMARY OF TEST RESULTS ....................................................................... 5 2.1 MEASUREMENT UNCERTAINTY .................................................................... 5 3 GENERAL INFORMATION ............................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT (GFSK) .................................................... 6 3.2 DESCRIPTION OF TEST MODES ................................................................... 7 3.3 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................... 7 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................... 9 3.5 DESCRIPTION OF SUPPORT UNITS ............................................................ 10 3.6 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 10 4 TEST PROCEDURES AND RESULTS ........................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT .................................................. 11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................... 11 4.1.2 TEST INSTRUMENTS .................................................................................... 11 4.1.3 TEST PROCEDURES ..................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ........................................................... 12 4.1.5 TEST SETUP .................................................................................................. 12 4.1.6 EUT OPERATING CONDITIONS .................................................................... 13 4.1.7 TEST RESULTS .............................................................................................. 14 4.2 RADIATED EMISSION AND BAND EDGE MEASUREMENT ........................ 16 4.2.1 LIMITS OF RADIATED EMISSION AND BAND EDGE MEASUREMENT ...... 16 4.2.2 TEST INSTRUMENTS .................................................................................... 17 4.2.3 TEST PROCEDURES ..................................................................................... 18 4.2.4 DEVIATION FROM TEST STANDARD ........................................................... 18 4.2.5 TEST SETUP .................................................................................................. 19 4.2.6 EUT OPERATING CONDITIONS .................................................................... 19 4.2.7 TEST RESULTS .............................................................................................. 20 5 PHOTOGRAPHS OF THE TEST CONFIGURATION ..................................... 25 6 INFORMATION ON THE TESTING LABORATORIES .................................... 26 7 APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ........................................................... 27 Report No.: RF141025E01-1 3 of 27 Report Format Version 5.0.1 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF141025E01-1 Original release Nov. 06, 2014 Report No.: RF141025E01-1 5 of 27 Report Format Version 5.0.1 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.249) STANDARD PARAGRAPH TEST TYPE RESULTREMARK 15.207 Conducted Emission Test PASS Meet the requirement of limit. Minimum passing margin is -7.34dB at 0.59531MHz 15.209 15.249 15.249 (d) Radiated Emission Test Band Edge Measurement Limit: 50dB less than the peak …

Text truncated - open the document above for the full version.

Report No.: RF141025E01 1 of 41 Report Format Version 5.2.1 FCC TEST REPORT (15.247, DTS) REPORT NO.: RF141025E01 MODEL NO.: M-R0052 FCC ID: JNZMR0052 RECEIVED: Oct. 25, 2014 TESTED: Oct. 27 to 31, 2014 ISSUED: Nov. 06, 2014 APPLICANT: LOGITECH FAR EAST LTD. ADDRESS: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, Taiwan, R.O.C. TEST LOCATION (2): No.49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF141025E01 2 of 41 Report Format Version 5.2.1 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................. 4 1 CERTIFICATION ............................................................................................ 5 2 SUMMARY OF TEST RESULTS .................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................. 7 3 GENERAL INFORMATION ............................................................................ 8 3.1 GENERAL DESCRIPTION OF EUT (DTS) .................................................... 8 3.2 DESCRIPTION OF TEST MODES ................................................................. 9 3.3 TEST MODE APPLICABLITY AND TESTED CHANNEL DETAIL: ............... 10 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................. 12 3.5 DUTY CYCLE OF TEST SIGNAL ................................................................ 13 3.6 DESCRIPTION OF SUPPORT UNITS ......................................................... 14 3.7 CONFIGURATION OF SYSTEM UNDER TEST .......................................... 14 4 TEST TYPES AND RESULTS ...................................................................... 15 4.1 CONDUCTED EMISSION MEASUREMENT ............................................... 15 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................ 15 4.1.2 TEST INSTRUMENTS ................................................................................ 15 4.1.3 TEST PROCEDURES ................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ....................................................... 16 4.1.5 TEST SETUP .............................................................................................. 16 4.1.6 EUT OPERATING CONDITIONS ................................................................ 17 4.1.7 TEST RESULTS .......................................................................................... 18 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ....................... 20 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ... 20 4.2.2 TEST INSTRUMENTS ................................................................................ 21 4.2.3 TEST PROCEDURES ................................................................................. 23 4.2.4 DEVIATION FROM TEST STANDARD ....................................................... 24 4.2.5 TEST SETUP .............................................................................................. 24 4.2.6 EUT OPERATING CONDITIONS ................................................................ 24 4.2.7 TEST RESULTS .......................................................................................... 25 4.3 6DB BANDWIDTH MEASUREMENT ........................................................... 29 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ....................................... 29 4.3.2 TEST INSTRUMENTS ................................................................................ 29 4.3.3 TEST PROCEDURE ................................................................................... 29 4.3.4 DEVIATION FROM TEST STANDARD ....................................................... 29 4.3.5 TEST SETUP .............................................................................................. 29 4.3.6 EUT OPERATING CONDITIONS ................................................................ 29 4.3.7 TEST RESULTS .......................................................................................... 30 4.4 CONDUCTED OUTPUT POWER MEASUREMENT ................................... 31 Report No.: RF14102…

Text truncated - open the document above for the full version.

Report No.: 120702E04 1 of 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 120702E04 2 of 3 RADIATED EMISSION TEST (BELOW 1GHz) Report No.: 120702E04 3 of 3 RADIATED EMISSION TEST (ABOVE 1GHz)