JNZMR00542.4GHz Cordless Mouse

English Read Manual Before Product Use. BATTERY WARNING!: Improperly replaced batteries may present a risk of leak or explosion and personal injury. Mistreated rechargeable batteries may present a risk of fire or chemical burn. Do not disassemble or expose to conducting materials, moisture, liquid, or heat above 54° C (130° F). Do not use or charge the battery if it appears to be leaking, discolored, deformed, or in any way abnormal. Do not leave your battery discharged or unused for extended periods. Do not short circuit. Your device may contain an internal, rechargeable battery that is not replaceable. Battery life varies with usage. Non-operational batteries should be discarded according to local laws. If no laws or regulations govern, dispose of your device in a waste bin for electronics. Keep batteries away from children. Class 1 Laser product: This optical device complies with International Standard IEC/EN 60825-1:2007, Class 1 Laser Product, and also complies with 21 CFR 1040.10, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007: 1) Emission of one or two independent parallel beams of infrared user-invisible light; 2) Maximum power of 716 microwatts CW, Emitted wavelength is 832 - 865 nm; 3) Operating temperature between 5° C and 40° C. WARNING! Use of controls, adjustments or performance of procedures beyond those specified herein may result in hazardous radiation exposure. The product contains Class 1 LED. Operating temperature between 0° C and 40° C. Class 1M Laser product: This optical device complies with International Standard IEC/EN 60825-1:2007, Class 1M Laser Product, and also complies with 21 CFR 1040.10, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007: 1) Emission of diverging beam of minimum +/-2° of infrared user-invisible light; 2) Maximum power of 1.4 milliwatts CW, Emitted wavelength is 832 - 865 nm; 3) Operating temperature between 5° C and 40° C. WARNING! Laser Radiation. Viewing the laser output with magnifying optical instruments within a 100mm distance may pose an eye hazard. INVISIBLE LASER RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LASER PRODUCT WARNING! The power supply is for indoor use only. Only use the power supply included with your product. Do not attempt to repair or use a damaged power supply. Do not immerse the power supply in water or subject it to physical abuse. Inspect the power supply regularly for cable, plug, and casing damage. Use Guidelines: Safe & Proper Use of Your Product • Do not open or modify the product except for battery removal and replacement. • Do not disassemble or attempt to service this product because there is a risk of radiation exposure, which could injury you. • Do not direct the infrared/laser beam at anyone’s eye or a reflective object. • Do not immerse product in any liquid or expose to heat or moisture. • If product is exposed to out-of-range temperature environments, power off the device until temperature has stabilized within the specified operating temperature range. • Use only Logitech-provided power supply devices with this product. Do not modify the power supply. Do not charge your product during an electrical storm. • This is not a Children’s Product and is not intended for use by children under 14 years old. • If product is operating improperly, call Logitech support. • Product must be returned to the manufacturer for any service or repair. • Long periods of repetitive motion using the product may be associated with nerve, tendon or muscle injury in your hands, wrists, arms, shoulders, neck or back. See a qualified health professional for pain, numbness, weakness, swelling, burning, cramping, or stiffness. Also, read guidelines at www.logitech.com/comfort. • This product is safe under normal and reasonably foreseeable misuse operating conditions. If the product is operating improperly, contact Logitech support. Product must be returned to Logitech for any service or repair. • Any changes or modifications to the product that are not expressly approved by Logitech may void the user’s authority to operate the equipment and your warranty. • Refer to product Quick Start Guide for use instructions. FCC statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates , uses and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Where shielded interface cables or accessories have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC. Changes or modifications to product not expressly approved by Logitech, Inc could void your right to use or operate your product by the FCC. IC statem…

Text truncated - open the document above for the full version.

G900 CHAOS SPECTRUM ™ Professional Grade Wired/Wireless Gaming Mouse Souris de jeu professionnelle laire/sans l Mouse para juegos profesional con/sin cable gaming.logitech.com/g900 L 620-007017.003 R 60cm+ M/N:C-U0008 CFT: RCPLOCU11-0321

Report No.: 151102E04 Page 1 CONSTRUCTION PHOTOS OF EUT Model No.: M-R0054

(Fig.1) FCC ID: JNZMR0054 FCC LABEL AND LOCATION The label will be permanently affixed at a conspicuous location on the device.

Report No.: 151102E04 Page 1 CONSTRUCTION PHOTOS OF EUT Model No.: M-R0054 Report No.: 151102E04 Page 2 Report No.: 151102E04 Page 3 Report No.: 151102E04 Page 4 Report No.: 151102E04 Page 5 Report No.: 151102E04 Page 6 Report No.: 151102E04 Page 7 Report No.: 151102E04 Page 8 Report No.: 151102E04 Page 9 Report No.: 151102E04 Page 10 Report No.: 151102E04 Page 11 Report No.: 151102E04 Page 12 Report No.: 151102E04 Page 13

Report No.: SA151102E04 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA151102E04 FCC ID: JNZMR0054 Test Model: M-R0054 Received Date: Nov. 02, 2015 Test Date: Nov. 20, 2015 Issued Date: Nov. 30, 2015 Applicant: LOGITECH FAR EAST LTD. Address: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA151102E04 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Evaluation Result .................................................................................................................................. 5 3 Antenna Gain ......................................................................................................................................... 6 4 SAR Test Exclusion Thresholds .......................................................................................................... 6 5 Conclusion ............................................................................................................................................ 6 Report No.: SA151102E04 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA151102E04 Original release. Nov. 30, 2015 Report No.: SA151102E04 Page No. 5 / 6 Report Format Version: 6.1.1 2 Evaluation Result Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation .  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA151102E04 Page No. 6 / 6 Report Format Version: 6.1.1 3 Antenna Gain The antenna provided to the EUT, please refer to the following table: Antenna Type Antenna Connector Gain (dBi) PCB printing Antenna NA 1.32 4 SAR Test Exclusion Thresholds Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 10-g extremity SAR test exclusion thresholds Result 2.402 ~ 2.481 3.899 5 1.2283 7.5 Pass NOTE: 1. The antenna type is PCB printed antenna with 1.32dBi gain. 2. Calculate SAR test exclusion thresholds f…

Text truncated - open the document above for the full version.

Report No.: RF151102E04 Page No. 1 / 35 Report Format Version: 6.1.1 FCC Test Report Report No.: RF151102E04 FCC ID: JNZMR0054 Test Model: M-R0054 Received Date: Nov. 02, 2015 Test Date: Nov. 19 to 21, 2015 Issued Date: Nov. 27, 2015 Applicant: LOGITECH FAR EAST LTD. Address: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF151102E04 Page No. 2 / 35 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Description of Support Units .............................................................................................................. 11 3.3.1 Configuration of System under Test ................................................................................................... 11 3.4 General Description of Applied Standards ........................................................................................ 12 4 Test Types and Results ...................................................................................................................... 13 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 13 4.1.2 Test Instruments ................................................................................................................................ 14 4.1.3 Test Procedures ................................................................................................................................. 15 4.1.4 Deviation from Test Standard ............................................................................................................ 15 4.1.5 Test Setup .......................................................................................................................................... 16 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Conducted Emission Measurement .................................................................................................. 22 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 22 4.2.2 Test Instruments ................................................................................................................................ 22 4.2.3 Test Procedures .......................................................................................…

Text truncated - open the document above for the full version.

Report No.: 150903E03 1 of 4 Reference No.: PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 150903E03 2 of 4 Reference No.: RADIATED EMISSION TEST (Below 1GHz) Report No.: 150903E03 3 of 4 Reference No.: RADIATED EMISSION TEST (Above 1GHz) Report No.: 150903E03 4 of 4 Reference No.: