JNZVR0025Wireless screen sharing kit

Important Safety, Compliance and Warranty Information Informations importantes concernant la sécurité, la mise en conformité et la garantie English Read Manual Before Product Use. Safe Usage Guidelines for Products − Do not open or modify the product except for battery removal and replacement. − Do not disassemble or attempt to service this product. − This product is safe under normal and reasonably foreseeable use operating conditions. − If product is operating improperly, please contact Logitech support. − Product must be returned to the manufacturer for any service or repair. − This is not a Children's Product and is not intended for use by children under 14 years old. − Warning: Not suitable for children under 36 months. Small parts. Choking hazard. − Install device according to provided instructions. Improper installation of this product may cause damage or injury. Logitech Compliance: The product complies with all applicable requirements for Restriction of Hazardous Substances (RoHS) and Waste Electronic and Electrical Equipment (WEEE). For Product Safety, EMC, RF, Energy, RoHS and WEEE information, go to www.logitech.com/compliance. Maintenance is not required for product compliance. Batteries, electronic and electrical equipment should not be disposed of with household waste. Wherever possible, they should be segregated and brought to an appropriate collection point to enable recycling and avoid potential impacts on the environment and human health. For more information, contact your local authorities or place of purchase, or visit www.logitech.com/recycling. FCC statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: − Reorient or relocate the receiving antenna. − Increase the separation between the equipment and receiver. − Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. − Consult the dealer or an experienced radio/TV technician for help. © 2021 Logitech, Logi and the Logitech Logo are trademarks or registered trademarks of Logitech Europe S.A. and/or its affiliates in the U.S. and other countries. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice. © 2021 Logitech, Logi et le logo Logitech sont des marques commerciales ou déposées de Logitech Europe S.A. et/ou de ses sociétés affiliées aux États-Unis et dans d’autres pays. Logitech décline toute responsabilité en cas d’erreurs dans ce manuel. Les informations énoncées dans le présent document peuvent faire l’objet de modifications sans avis préalable. 620-010925.002 Attention: (i) le dispositif prévu pour fonctionner dans la bande 5150-5250 MHz est destiné à un usage intérieur uniquement afin de réduire la possibilité d'interférence nuisible avec les systèmes à satellites mobiles du même canal; (ii) les radars à haute puissance sont alloués en tant qu'utilisateurs principaux (c'est-à-dire utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650- 5850 MHz, et peuvent provoquer des interférences ou des dommages sur les dispositifs LE-LAN. Déclaration sur la radioexposition - [Kit de partage d’écran sans fil] Cet équipement est conforme aux limitations prévues par la FCC et l'Industry Canada en matière d'exposition aux radiations des dispositifs portables. Cet émetteur ne doit pas être installé ou utilisé en conjonction avec une autre antenne ou un autre émetteur. Déclaration IC: CAN ICES-3 (B) / NMB-3 (B) Ce dispositif contient un(des) émetteur(s)/récepteur(s) exempt(s) de licence et conforme(s) à la(aux) norme(s) RSS exempte(s) de licence d'Innovation, Sciences et Développement économique Canada. Son utilisation est soumise aux deux conditions suivantes: (1) Ce dispositif ne doit pas causer d'interférences. (2) Ce dispositif doit accepter toute interférence, y compris les interférences risquant d'engendrer un fonctionnement indésirable. Garantie matérielle limitée de Logitech - Récapitulatif Logitech garantit que son produit matériel est exempt de tout défaut matériel et de fabrication pour la période indiquée sur l'emballage du produit à partir de la date d'achat d'origine. Pour les informations spécifiques relatives à la garantie de votre produit et les procédures de réclamations de garantie, rendez-vous sur support.logitech.com. En cas de rupture de garantie, l'intégralité de la responsabilité de Logitech et votre recours exclusif consisteront, à la discrétion de Logitech, à réparer le matériel ou à le remplacer par un produit équivalent et fonctionnel, ou à rembourser le prix d'achat, sous réserve que le matériel soit renvoyé au point de vente ou à tout autre lieu indiqué par Logitech, accompagné d'un justificatif d'achat. La protection offerte par cette garantie vient s'ajouter aux droits conférés par la législation locale relative aux droits des consommateurs et peut varier selon les pays. Consultez les inf…

Text truncated - open the document above for the full version.

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: JNZVR0025 To Whom It May Concern: PXrVXanW Wo Whe proYiVionV of SecWionV 0.457 and 0.459 of Whe CommiVVion¶V rXleV (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the CommiVVion¶V polic\, in order Wo compl\ ZiWh Whe markeWing regXlaWionV in 47 CFR †2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant of Equipment Authorization. External Photos Internal Photos User Manual Test Setup photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Bonnie Chou / Sr. Certification Engineer LOGITECH FAR EAST LTD. Tel: +886 3 5778241* 2053 Fax: +886 3 5792393 E-mail: [email protected] 08/21/2020

AGENCY AUTHORIZATION LETTER To whom it may concern: We, the undersigned, hereby authorize Amanda Wu / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu / Senior Specialist of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If \oX haYe an\ TXeVWionV UegaUding Whe aXWhoUi]aWion, pleaVe don¶W heViWaWe Wo conWacW XV. FCC ID: JNZVR0025 Sincerely yours, ----------------------------------- Bonnie Chou / Sr. Certification Engineer LOGITECH FAR EAST LTD. Tel: +886 3 5778241* 2053 Fax: +886 3 5792393 E-mail: [email protected] 08/21/2020

Reference No.: 200811E02 Page 1/6 CONSTRUCTION PHOTOS OF EUT EUT + USB to type C Adapter Reference No.: 200811E02 Page 2/6 EUT Reference No.: 200811E02 Page 3/6 Reference No.: 200811E02 Page 4/6 Reference No.: 200811E02 Page 5/6 Reference No.: 200811E02 Page 6/6 USB to type C Adapter

Label & Label location The label will be permanently affixed at a conspicuous location on the device. Back M/N: VR0025 FCC ID: JNZVR0025

Reference No.: 200811E02-1 Page 1/7 CONSTRUCTION PHOTOS OF EUT EUT Reference No.: 200811E02-1 Page 2/7 Reference No.: 200811E02-1 Page 3/7 Reference No.: 200811E02-1 Page 4/7 Reference No.: 200811E02-1 Page 5/7 Reference No.: 200811E02-1 Page 6/7 Reference No.: 200811E02-1 Page 7/7 Antenna

SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 24 Report No. : SF200811E02 Issued Date : Nov. 04, 2020 SAR Test Report Report No. : SF200811E02 Applicant : Logitech Europe S.A.(For CE Only) LOGITECH FAR EAST LTD.(For others) Address : EPFL – Quartier de I’Innovation Daniel Borel Innovation Center,1015 Lausanne, Switzerland.(For CE Only)#2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C.(For Others) Product : Wireless screen sharing kit FCC ID : JNZVR0025 Brand : Logitech Model No. : VR0025 Standards : FCC 47 CFR Part 2 (2.1093), IEEE C95.1:1992, IEEE Std 1528:2013 KDB 865664 D01 v01r04, KDB 865664 D02 v01r02 KDB 248227 D01 v02r02, KDB 447498 D01 v06, KDB 447498 D02 v02r01 Sample Received Date : Aug. 11, 2020 Date of Testing : Sep. 10, 2020 ~ Oct. 29, 2020 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Shelly Hsueh / Specialist Approved By : Gordon Lin / Manager FCC Accredited No.: TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 24 Report No. : SF200811E02 Issued Date : Nov. 04, 2020 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY6 System ............................................................................................................................................... 6 3.2.1 Robot ............................................................................................................................................................... 7 3.2.2 Probes ............................................................................................................................................................. 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................. 8 3.2.4 Phantoms ......................................................................................................................................................... 8 3.2.5 Device Holder .................................................................................................................................................. 9 3.2.6 System Validation Dipoles ............................................................................................................................. 10 3.2.7 Power Source ................................................................................................................................................ 10 3.2.8 Tissue Simulating Liquids .............................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 13 3.4 SAR Measurement Procedure ................................................................................................................................... 14 3.4.1 Area Scan and Zoom Scan Procedure .......................................................................................................... 14 3.4.2 Volum…

Text truncated - open the document above for the full version.

Report No.: RF200811E02 Page No. 1 / 74 Report Format Version:6.1.2 FCC Test Report Report No.: RF200811E02 FCC ID: JNZVR0025 Test Model: VR0025 Received Date: Aug. 11, 2020 Test Date: Aug. 19 to Nov. 10, 2020 Issued Date: Dec. 04, 2020 Applicant: LOGITECH FAR EAST LTD. Address: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwa. Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF200811E02 Page No. 2 / 74 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Duty Cycle of Test Signal .................................................................................................................. 12 3.4 Description of Support Units ............................................................................................................. 13 3.4.1 Configuration of System under Test .................................................................................................. 14 3.5 General Description of Applied Standard and references ................................................................. 16 4 Test Types and Results ...................................................................................................................... 17 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 17 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 17 4.1.2 Test Instruments ................................................................................................................................ 18 4.1.3 Test Procedure .................................................................................................................................. 21 4.1.4 Deviation from Test Standard ............................................................................................................ 22 4.1.5 Test Setup .......................................................................................................................................... 22 4.1.6 EUT Operating Condition .................................................................................................................. 23 4.1.7 Test Results ....................................................................................................................................... 24 4.2 Conducted Emission Measurement .................................................................................................. 44 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 44 4.2.2 Test Instruments ................................................................................................................................ 44 4.2.3 Test Procedure .................................................................................................................................. 45 4.2.4 Deviation from Test Standard ............................................................................................................ 45 4.2.5 Test Setup ....…

Text truncated - open the document above for the full version.

SAR Test Report Report Format Version 5.0.0 Report No. : SF200811E02 <Photographs of EUT> SAR Test Report Report Format Version 5.0.0 Report No. : SF200811E02 <Antenna Location> SAR Test Report Report Format Version 5.0.0 Report No. : SF200811E02 <Photographs of SAR Setup> USB Horizontal Up at 5 mm USB Horizontal Down at 5 mm USB Vertical Front at 5 mm USB Vertical Back at 5 mm USB Tip at 5 mm

Reference No.: 200811E02 Page No. 1 / 5 Report No.: RT200811E02 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Reference No.: 200811E02 Page No. 2 / 5 Report No.: RT200811E02 RADIATED EMISSION TEST (Below 1GHz) Reference No.: 200811E02 Page No. 3 / 5 Report No.: RT200811E02 Reference No.: 200811E02 Page No. 4 / 5 Report No.: RT200811E02 RADIATED EMISSION TEST (Above 1GHz) Reference No.: 200811E02 Page No. 5 / 5 Report No.: RT200811E02