JPZ0090Shadow Sensor

Mounting 1 Prepare the window glass surface by wiping with a clean, dry cloth. 2 First, read all the remaining steps and notes in this section, then peel off the protective adhesive liner on the back of the sensor and proceed immediately to step 3. 3 With the arrow on the front of the sensor pointing straight up, press the sensor fi rmly to the window surface, holding for a minimum of 5 seconds. NOTE: The sensor can be removed and repositioned one time within 15 seconds of initial contact with the window surface. After 15 seconds, or if a second repositioning is necessary, you must replace the sensor’s back cover with Lutron Part Number: “RSS-REPCOVER” IMPORTANT: The factory-applied mounting adhesive is positioned to allow the sensor to operate properly. DO NOT apply any other type of adhesive. Application of additional tape or liquid bonding agents will obstruct the sensor and/or cause permanent damage. Instructions Install a sensor in as little as 15 minutes. Getting Started: Key Features • Easy Installation. No wiring required. • Easy Set-Up. Default settings are ideal for most situations. Simple and intuitive adjustments available. • Low Maintenance. 10-year battery life. Sensor Operation: Hyperion solar-adaptive shading technology automatically positions shades based on the position of the sun. The Radio Shadow Sensor will monitor exterior lighting conditions and override Hyperion when shadows are cast by clouds or neighboring buildings, and re-enable Hyperion when sunlight returns. How it works: • This battery powered photo sensor reports the measured amount of natural light incident on a facade to Quantum using Lutron Clear Connect Technology. • Enables Quantum to override Hyperion by moving shades to an opened visor position when outdoor conditions indicate shadows from clouds or other obstructions. REAR VIEW w/COVER REMOVEDFRONT VIEW Use laser to link to system Battery compartment door Battery compartment Use to test system functionality Use to link to system ® Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. Made and printed in the U.S.A. 10/12 P/N 045-379 Rev. A Important Notes 1. This sensor is part of a system and cannot be used to control a load or shade without a compatible Lutron Quantum Total Light Management System with Hyperion Solar Adaptive Technology. Refer to the instruction sheets of the receiving devices for installation information on setup and testing of this sensor. 2. Clean sensor with a soft damp cloth only. DO NOT use any chemical cleaners. 3. For indoor use only. Operate between 32 °F and 122 °F (0 °C and 50 °C). 4. DO NOT paint sensor. 5. Use only high-quality lithium batteries, one (1) size CR2450, 3 V (ANSI-5029LC, IEC-CR2450). DO NOT use rechargeable batteries. Using improperly rated batteries could damage the sensor. NOTICE: DO NOT disassemble, crush, puncture, or incinerate batteries. DO NOT dispose of batteries in normal household waste. Please recycle, take to a proper battery disposal facility, or contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. WARNING: Keep battery out of reach of children. If swallowed, immediately seek medical help as serious injury may occur. Have doctor phone 24-hour hotline at (202) 625-3333, collect. 6. California residents: The batteries in these devices contain Perchlorate Material–special handling may apply. For more information visit www.dtsc.ca.gov/hazardouswaste/perchlorate. 7. The range and performance of the RF system is highly dependent on a variety of complex factors such as: • Distance between system components • Geometry of the building structure • Construction of walls separating system components • Electrical equipment located near system components WARNING: Entrapment hazard. To avoid the risk of entrapment this product must not be used to control equipment which could create hazardous situations, such as entrapment, if operated accidentally. Examples of equipment which must not be controlled with this product include (but are not limited to) motorized gates, garage doors, industrial doors, etc. Accidental operation of the above equipment with this product could result in serious injury or death. Easy-to-follow Instructions P/N 045-379 Limited Warranty (Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.) Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CON NEC TION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PUR CHASE PRICE OF THE UNIT. This warranty gives you specifi c legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you. Lutron, Maestro Wireless, Grafi k Eye and the Sunburst logo are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American National Standards Institute. IEC is a trademark of the International Electrotechnical Commission. 3M and Command are trademarks of 3M Company. © 2010 Lutron Electronics Co., Inc. Technical Assistance For questions concerning the installation or operation of this product, ca…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR EUT MODEL NUMBER: LRF2-SSW FCC ID: JPZ0090 IC: 2851A-JPZ0090 REPORT NUMBER: 1001550724 ISSUE DATE: 2012-10-02 Prepared for LUTRON ELECTRONICS CO INC 7200 SUTER RD COOPERSBURG , PA 18036 USA Prepared by UL LLC 1285 WALT WHITMAN RD. MELVILLE, NY 11747, U.S.A. TEL: (631) 271-6200 FAX: (877) 854-3577 REPORT NO: 1001550724 DATE: 2012-10-02 FCC ID: JPZ0090 IC: 2851A-JPZ0090 Page 2 of 31 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. Revision History Rev. Issue Date Revisions Revised By -- 2012- 10-02 Initial Issue B. DeLisi REPORT NO: 1001550724 DATE: 2012-10-02 FCC ID: JPZ0090 IC: 2851A-JPZ0090 Page 3 of 31 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ................................................................................ 5 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 5 4.2. SAMPLE CALCULATION ............................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 5 5. EQUIPMENT UNDER TEST ............................................................................................... 6 5.1. DESCRIPTION OF EUT .............................................................................................. 6 5.2. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 6 5.3. SOFTWARE AND FIRMWARE .................................................................................... 6 5.4. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.5. MODIFICATIONS ........................................................................................................ 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................ 6 6. ANTENNA PORT TEST RESULTS .................................................................................... 8 6.1. 20 dB AND 99% BW .................................................................................................... 8 6.2. DUTY CYCLE .............................................................................................................12 6.3. TRANSMISSION TIME ...............................................................................................16 7. RADIATED EMISSION TEST RESULTS...........................................................................17 7.1. TX RADIATED SPURIOUS EMISSION ......................................................................17 8. SETUP PHOTOS ...............................................................................................................28 REPORT NO: 1001550724 DATE: 2012-10-02 FCC ID: JPZ0090 IC: 2851A-JPZ0090 Page 4 of 31 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: Lutron Electronics Inc. 7200 Suter Rd Coopersburg , PA 18036 USA EUT DESCRIPTION: Radio Shadow Sensor MODEL: LRF2-SSW SERIAL NUMBER: Non-Serialized production unit DATE TESTED: 2012-09-24 through 2012-09-25 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C Pass INDUSTRY CANADA RSS-210 Issue 8, Annex 1 Pass INDUSTRY CANADA RSS-GEN Issue 3 Pass UL LLC tested the above equipment in accordance with the requirements set forth in the above standards, using test results reported in the test report documents referenced below and/or documentation furnished by the applicant. All indications of Pass/Fail in this report are opinions expressed by UL LLC based on interpretations of these calculations. The results show that the equipment is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation, as described by the referenced documents. This document may not be altered or revised in any way unless done so by UL LLC and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL LLC will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL By: Tested By: Joseph Danisi Bob DeLisi WiSE Project Lead WiSE Principle Engineer UL LLC UL LLC REPORT NO: 1001550724 DATE: 2012-10-02 FCC ID: JPZ0090 IC: 2851A-JPZ0090 Page 5 of 31 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.10-2009, FCC CFR 47 Part 2, FCC CFR 47 Part 15, RSS-GEN Issue 3, and RSS-210 Issue 8. 3. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data ar…

Text truncated - open the document above for the full version.

1. SETUP PHOTOS ANTENNA PORT ANTENNA PORT RADIATED EMISSION FOR PORTABLE CONFIGURATION – X ORIENTATION RADIATED EMISSION FOR PORTABLE CONFIGURATION – X ORIENTATION RADIATED EMISSION FOR PORTABLE CONFIGURATION – Y ORIENTATION RADIATED EMISSION FOR PORTABLE CONFIGURATION – Y ORIENTATION RADIATED EMISSION ABOVE 30 MHz END OF REPORT RADIATED EMISSIONS ABOVE 30 MHz