JPZ0095Roller Shade

Roller Shade • Installation and Setup Guide—Please Read Before Installing and OperatingBattery Powered Window Shade with RF Wireless Remote Control Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. 09/2013 P/N 045404 Rev. A Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc. Equal depth both sides A 1 Mounting the shade rail: 3 Hanging the shade: 2 Installing the end caps on optional fascia: 2.1 Press-fit an end cap on the open end of the fascia as shown. 2.2 Repeat on the other end. 3.1 Facing the window, tilt the top of the shade assembly C away from you and insert its top rear edge into the channel in the shade rail A . 3.2 Push the bottom of the shade toward the window and lock it into the shade rail with a “click.” 1.1 Hold the shade rail A up to the mounting surface. Approximate its final position and use a pencil to mark mounting screw locations on the shade rail.* 1.2 Pre-drill the shade rail A at the pencil marks. 1.3 Fasten the shade rail A , to the mounting surface using the mounting screws provided B or other appropriate fasteners. NOTE: The shade rail features grooves to help stabilize the point of your drill bit. **NOTE: Depending on the size of your shade and the depth of your trim, or the roll direction of your shade, you may be able to mount the shade directly to the wall above the trim without additional spacing. In this arrangement, the top of the shade rail must be a minimum of 4 1 /2 in (114 mm) above the top of the trim. Optional fascia/end caps not shown NOTE: If your shade was ordered with optional fascia, the fascia will be factory-attached and wrapped with the shade. Leave the wrapping in place during installation for added stability, then remove the wrap before installing batteries. *To ensure the shade rail is properly mounted, we rcommend: a. Install mounting screws 6-12 in (152-305 mm) from each end of the shade rail. b. Locate the mounting screws so that they drive into studs or solid trim. For other surfaces, use appropriate expansion anchors, toggle bolts, or other fasteners, (not included). c. Verify that the mounted shade rail is level and parallel to the window opening. #2 Phillips Driver Bit 1/8 in (3.2 mm) Drill Bit Pencil Level D-Cell Alkaline Batteries (6 or 8 depending on shade size)Power Drill OPTIONAL (1) Shade Rail A Mounting Screws B Serena® Roller Shade Assembly C (1) Fascia with end caps D CLICK! CLICK! A B A C A Outside Mount on Trim Outside Mount above Trim A Spacer blocks or board (not included) securely mounted to wall above trim** GROOVES Worldwide Headquarters | USA Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USA TEL: 1.610.282.3800 • FAX: 1.610.282.3090 Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1 Email: [email protected] • Online: www.lutron.com/shadingsolutions Europe Headquarters | United Kingdom Lutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UK TEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899 Technical Support: +44.(0)20.7680.4481 FREEPHONE: 0800.282.107 Inside Mount B B Included in the box: Other items you’ll need: End Caps Left end cap shown Left end cap installed Fascia LeftRight NOTE: If your shade will be inside- mounted, both end caps must be installed and fully seated before proceeding to the next step. 4.5 in (114 m m) min. Wall Regular roll Reverse roll Trim Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. 09/2013 P/N 045404 Rev. A Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc. Serena® Roller Shade Installation and Setup GuidePage 2 6 Adjusting shade limits and presets (OPTIONAL): 6.1 Adjust Upper or Lower Limit (OPTIONAL) The shade’s upper and lower limits are pre-programmed based on the window dimensions and mounting option. If adjustment is needed, follow these steps: Serena® 4-Group RF remote control Shade Button with LED Open Close ShadeAll 1 2 3 4 Open Close ShadeAll 1 2 3 4 5 Assigning a remote control: Pico® wireless control Exposed headrail: rotate the top section forward.Exposed headrail: rotate the top section back to the closed position Open Open Preset Preset Close Close Shade Groups Lower Lower All Shade Groups Raise Raise 5.1 Assign a Pico® Wireless Control Press and hold the Close button. Tap the Shade Button. Tap the Shade Button. The Shade Button lights. The Shade Button lights. The Shade Button flashes. Assignment is complete. The Shade Button flashes. Assignment is complete. Repeat for additional shade/control assignments. Repeat for additional shade/control assignments. 5.2 Assign a Serena® 4-Group RF Remote Control Choose a Shade Group button. Press and hold. The Shade Button flashes, then stays on. Compatible Remote Controls (sold separately) Press and hold the Open and Raise Buttons. Press and hold the Preset Button. Use the Raise and Lower Buttons to position the shade at the preferred upper or lower limit. 6.2 Set Preset Level (OPTIONAL) The preset level is factory programmed to 50% open/closed. Tap the Shade Button. The Shade Button lights. The Shade Button flashes. Limit set is complete. The Shade Button flashes. Preset level is set. SET UPPER LIMIT With the shade at the preferred upper limit, press and hold the Open Button. OR SET LOWER LIMIT With the shade at the preferred lower limit, press and hold the Close Button. Use the Raise and Lower Buttons to position the shade at the desired preset level. 4 Installing the batteries: 4.1 Open the battery holder at the top of the shade. 4.2 Insert new D-cell alkaline batteries. 4.3 Return the battery holder to the closed position. With optional fascia: pull straight down on the fascia.With optional fascia: gently push straight up on the fascia.A label on the battery holder shows quanity and orientation. FCC Information Models: SYC-J-EDU-R2, QSFC-J-EDU-R2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR MOTORIZED SHADES DRIVE MODEL NUMBER: QSFC-J-EDU-R2 FCC ID: JPZ0095 IC: 2851A-JPZ0095 REPORT NUMBER: 10052927-AC ISSUE DATE: 2013-09-13 Prepared for LUTRON ELECTRONICS CO INC 7200 SUTER RD COOPERSBURG , PA 18036 USA Prepared by UL LLC 1285 WALT WHITMAN RD. MELVILLE, NY 11747, U.S.A. TEL: (631) 271-6200 FAX: (877) 854-3577 REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 2 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. Revision History Rev. Issue Date Revisions Revised By -- 2013- 09-13 Initial Issue B. DeLisi REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 3 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ................................................................................ 5 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 5 4.2. SAMPLE CALCULATION ............................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 5 5. EQUIPMENT UNDER TEST ............................................................................................... 6 5.1. DESCRIPTION OF EUT .............................................................................................. 6 5.2. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 6 5.3. SOFTWARE AND FIRMWARE .................................................................................... 6 5.4. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.5. MODIFICATIONS ........................................................................................................ 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 9 7. ANTENNA PORT TEST RESULTS ...................................................................................11 7.1. 20 dB AND 99% BW ...................................................................................................11 7.2. DUTY CYCLE .............................................................................................................15 7.3. TRANSMISSION TIME ...............................................................................................19 8. RADIATED EMISSION TEST RESULTS...........................................................................21 8.1. TX RADIATED SPURIOUS EMISSION ......................................................................21 8.2. RX RADIATED SPURIOUS EMISSION ......................................................................29 9. AC MAINS LINE CONDUCTED EMISSIONS ....................................................................34 10. SETUP PHOTOS ...........................................................................................................47 REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 4 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: LUTRON ELECTRONICS CO INC 7200 SUTER RD COOPERSBURG , PA 18036 USA EUT DESCRIPTION: Motorized Shade Drive MODEL: QSFC-J-EDU-R2 SERIAL NUMBER: Non-serialized production unit DATE TESTED: 2013-08-29 through 2013-09-06 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C Pass INDUSTRY CANADA RSS-210 Issue 8, Annex 1 Pass INDUSTRY CANADA RSS-GEN Issue 3 Pass UL LLC tested the above equipment in accordance with the requirements set forth in the above standards, using test results reported in the test report documents referenced below and/or documentation furnished by the applicant. All indications of Pass/Fail in this report are opinions expressed by UL LLC based on interpretations of these calculations. The results show that the equipment is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation, as described by the referenced documents. This document may not be altered or revised in any way unless done so by UL LLC and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL LLC will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL By: Tested By: Bob DeLisi Joseph Danisi WiSE Principal Engineer WiSE Project Lead UL LLC UL LLC REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 5 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR MOTORIZED SHADES DRIVE MODEL NUMBER: QSFC-J-EDU-R2 FCC ID: JPZ0095 IC: 2851A-JPZ0095 REPORT NUMBER: 10052927-DC ISSUE DATE: 2013-09-13 Prepared for LUTRON ELECTRONICS CO INC 7200 SUTER RD COOPERSBURG , PA 18036 USA Prepared by UL LLC 1285 WALT WHITMAN RD. MELVILLE, NY 11747, U.S.A. TEL: (631) 271-6200 FAX: (877) 854-3577 REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 2 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. Revision History Rev. Issue Date Revisions Revised By -- 2013- 09-13 Initial Issue B. DeLisi REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 3 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ................................................................................ 5 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 5 4.2. SAMPLE CALCULATION ............................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 5 5. EQUIPMENT UNDER TEST ............................................................................................... 6 5.1. DESCRIPTION OF EUT .............................................................................................. 6 5.2. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 6 5.3. SOFTWARE AND FIRMWARE .................................................................................... 6 5.4. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.5. MODIFICATIONS ........................................................................................................ 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 9 7. ANTENNA PORT TEST RESULTS ...................................................................................11 7.1. 20 dB AND 99% BW ...................................................................................................11 7.2. DUTY CYCLE .............................................................................................................15 7.3. TRANSMISSION TIME ...............................................................................................19 8. RADIATED EMISSION TEST RESULTS...........................................................................21 8.1. TX RADIATED SPURIOUS EMISSION ......................................................................21 8.2. RX RADIATED SPURIOUS EMISSION ......................................................................29 9. SETUP PHOTOS ...............................................................................................................34 REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 4 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: LUTRON ELECTRONICS CO INC 7200 SUTER RD COOPERSBURG , PA 18036 USA EUT DESCRIPTION: Motorized Shade Drive MODEL: QSFC-J-EDU-R2 SERIAL NUMBER: Non-serialized production unit DATE TESTED: 2013-08-29 through 2013-09-06 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C Pass INDUSTRY CANADA RSS-210 Issue 8, Annex 1 Pass INDUSTRY CANADA RSS-GEN Issue 3 Pass UL LLC tested the above equipment in accordance with the requirements set forth in the above standards, using test results reported in the test report documents referenced below and/or documentation furnished by the applicant. All indications of Pass/Fail in this report are opinions expressed by UL LLC based on interpretations of these calculations. The results show that the equipment is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation, as described by the referenced documents. This document may not be altered or revised in any way unless done so by UL LLC and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL LLC will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL By: Tested By: Bob DeLisi Joseph Danisi WiSE Principal Engineer WiSE Project Lead UL LLC UL LLC REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 5 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 2. TEST METHODOLOGY The tests …

Text truncated - open the document above for the full version.

REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 47 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 10. SETUP PHOTOS ANTENNA PORT ANTENNA PORT REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 48 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSION BELOW 30 MHz RADIATED EMISSIONS BELOW 30MHz (FRONT) REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 49 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSIONS BELOW 30MHz (BACK) REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 50 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSION ABOVE 30 MHz RADIATED EMISSIONS ABOVE 30 MHz (FRONT) REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 51 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSIONS ABOVE 30 MHz (BACK) REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 52 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. AC MAINS LINE CONDUCTED EMISSION LINE CONDUCTED EMISSION (FRONT) REPORT NO: 10052927-AC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 53 of 53 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. END OF REPORT LINE CONDUCTED EMISSION (BACK)

REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 34 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. 9. SETUP PHOTOS ANTENNA PORT ANTENNA PORT REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 35 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSION BELOW 30 MHz RADIATED EMISSIONS BELOW 30MHz (FRONT) REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 36 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSIONS BELOW 30MHz (BACK) REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 37 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. RADIATED EMISSION ABOVE 30 MHz RADIATED EMISSIONS ABOVE 30 MHz (FRONT) REPORT NO: 10052927-DC DATE: 2013-09-13 FCC ID: JPZ0095 IC: 2851A-JPZ0095 Page 38 of 38 UL LLC. FORM NO: CCSUP4701D 1285 WALT WHITMAN RD, MELVILLE, NY 11747, USA TEL: (631) 271-6200 FAX: (877) 854-3577 This report shall not be reproduced except in full, without the written approval of UL LLC. END OF REPORT RADIATED EMISSIONS ABOVE 30 MHz (BACK)