
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Radio Powr Savr Occupancy Sensor Pico Remote Control PowPak Dimming Module 30 ft (9 m) max 40 ft (12 m) 30 ft (9 m) PowPak Dimming Module Install in center of room to maximize RF coverage. A Connect mains wiring (switched hot, neutral) to each fixture. B Connect 0 –10 V- control (+ and – ) to each fixture. 1 + – NEU HOT Class 2 MAINS Fixture Earth Green/Yellow To additional 0 –10 V- fixtures Neutral Switched Line/Hot Violet Pink* + – WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit. Sample ballast shown Start Here Mount, Wire, and Install 0 –10 V- Devices and Lighting Fixtures Consult third-party device installation guide 2 A PowPak Dimming Module with 0 –10 V- can be installed on a junction box or marshalling box using the conduit nut (provided) or with mounting screws (not provided). The device must NOT be mounted inside a fixture or other metallic enclosure – only on the exterior of a fixture. Please consult local and national electric codes for proper installation. If installing unit inside a junction box, please see Application Note #423 (P/N 048423 at www.lutron.com). B Once installed, energize the PowPak Dimming Module with 0 –10 V-. C Use the Toggle button “ u” to toggle between high-end and OFF to verify ballast wiring. D Use the Raise “ ▲ ” and Lower “ Δ ” buttons to verify control wiring. Install PowPak Dimming Module with 0 –10 V- Suggested Installation Location: Center of room to ensure proper RF coverage of area. Switched Line/Hot (Red) – Line/Hot (Black) To Fixtures 0 –10 V- to Fixtures* Neutral (White) + Neutral Junction Box 1/2 in (21 mm) Knockout Opening Conduit Nut RMJS-8T-DV-B / URMJS-8T-DV-B Switched Line/Hot (Red) – (Pink) Line/Hot (Black) To Fixtures 0 –10 V- to Fixtures * Neutral (White) + (Violet) Neutral Junction Box 1/2 in (21 mm) Knockout Opening Conduit Nut RMJS-8TN-DV-B Switched Line / Hot (Red) – (Pink) Line / Hot (Black) To Emergency Fixtures 0 –10 V- to Emergency Fixtures* Neutral (White) + (Violet) Neutral Junction Box 1/2 in (21 mm) Knockout Opening Conduit Nut Emergency Backup Generator Automatic Transfer Switch Regular Utility Power Neutral 120 / 277 V~ Normal Feed Neutral 120 / 277 V~ Emergency Feed Note: For periodic testing and maintanance of emergency systems, use the toggle button of the RMJS-8T-DV-B-EM to ensure proper operation. Make sure PowPak buttons remain accessible. Note: Momentary power outages can envoke emergency mode on the dimming module. See Troubleshooting section for details. RMJS-8T-DV-B-EM * Use 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) solid wire only vive.lutron.com X Programming with a Vive Hub 3 A Use an iOS® or Android® compatible device. C Open the app and follow the instructions. Note: For further information on set up, programming, and troubleshooting with a Vive system, please refer to the installation instructions included with the Vive hub or visit www.lutron.com/vive Note: For programming the PowPak Dimming Module without a Vive hub see reverse side. X Vive B Download the Lutron Vive app. 041588 Rev. A 04/2022 PowPak | Installation Dimming Module with 0 –10 V- English All Wireless Transmitters must be installed within 30 ft (9 m) of the PowPak Dimming Module with 0 –10 V-. 0 –10 V- Control: 10 V- 60 mA UL 2043 Plenum Rated Compatible with ANSI E1.3 2001 (R2006), IEC 60929 Annex E 120 / 277 V~ 50 / 60 Hz 8 A RMJS-8T-DV-B URMJS-8T-DV-B RMJS-8TN-DV-B Important Notes: Please read before installing. For installation by a qualified electrician in accordance with all local and national electrical codes (including periodic testing and maintenance of emergency systems). • Note: Use copper conductors only. • Check to see that the device type and rating is suitable for the application. • DO NOT install if product has any visible damage. • If moisture or condensation is evident, allow the product to dry completely before installation. • Operate between 32 °F and 104 °F (0 °C and 40 °C) ambient. • 0% to 90% humidity, non-condensing. • For indoor use only. Note for Replacement: RMxS and URMxS - the "S" model can replace the non-"S" model 041856 Rev. A 04/2022 Part of the Vive Family 120 / 277 V~ 50 / 60 Hz 8 A RMJS-8T-DV-B-EM IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. • Do not use outdoors. • Do not mount near gas or electric heaters. • Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel. • The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. • Do not use this equipment for other than its intended use. SAVE THESE INSTRUCTIONS Test Link Cal. + For each system, ensure that you have: One PowPak Dimming ModuleAt least one Wireless TransmitterAt least one 0 –10 V- Fluorescent Ballast or LED Driver Required Components Radio Powr Savr Occupancy / Vacancy Sensor (10 maximum) Radio Powr Savr Daylight Sensor (1 maximum) Pico Remote Control (10 maximum) 60 mA maximum for the control lines. Switches up to 8 A total. May be pre-installed in light fixture. Note: All drivers and ballasts used with Vive wireless controls must comply with the limits for a Class A device, pursuant to Part 15 of the FCC rules. PowPak Dimming Module with 0 –10 V- (1 maximum) Raise Toggle Lower Load Status LED Consult third-party 0 –10 V- fixtures installation guide for fixture-specific wiring. For mounting and wiring best practices see Lutron Application Note #620 (P/N 048620). + Customer Assistance www.lutron.com/support Wireless Controls: All lights Default Functionality Daylight Sensor All lights dim in response to daylight. On: 100% ; Favorite: 50%; Off: 0% Occupancy Sensors Occupied: All lights100% ; Unoccupied: All lights off Lutron Electronics Co., Inc. | 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. * This wire may be gray on older product…
Text truncated - open the document above for the full version.