K7S-03535AX1800 Dual-Band WiFi 6 Router

FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and devices • Connect the equipment to an outlet other than the receiver’s • Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. 2.4GHz operation of this product in the USA is firmware-limited to channels 1 through 11. The device for the band 5150-5250 MHz is only for indoor usage. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 35 cm between the radiator and your body. This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Additional requirements for the band 5600-5650 MHz Until further notice, devices subject to this Section shall not be capable of transmitting in the band 5600-5650 MHz, so that Environment Canada weather radars operating in this band are protected. Wireless Disclaimer The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions. Safety Notices English WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: The power adaptor is the equipment ́s disconnection device. The power outlet must be located nearby the equipment and its access must be easy. This product is intended for indoor use only. Español ADVERTENCIA: No use este producto cerca del agua, por ejemplo en un sotano húmedo o cerca de una piscina. ADVERTENCIA: Evite usar este producto durante una tormenta eléctrica. Puede existir el riesgo remoto de que se produzca una descarga eléctrica producida por un rayo. ADVERTENCIA: El adaptador de alimentación es el dispositivo de desconexión del equipo. La base de toma de corriente debe estar cerca del equipo y ser fácilmente accessible. Este producto está destinado solo para uso en interiores. Third-Party Software or Firmware The use of software or firmware not supported/provided by Linksys products may result that the equipment is no longer compliant with the regulatory requirements. 8850-01177 Rev. A00 WARRANTY AND SUPPORT INFORMATION IMPORTANT! PLEASE RETAIN PROOF OF PURCHASE AND PRODUCT WARRANTY INFORMATION LIMITED WARRANTY (UNITED STATES AND CANADA) This warranty is provided to you by Belkin International, Inc, or one of its subsidiaries or affiliates (“Belkin”) IMPORTANT NOTICE REGARDING YOUR CONSUMER RIGHTS The benefits we give in this manufacturer’s warranty are additional to any rights and remedies that you may have under local consumer protection laws. Nothing in this warranty limits or affects your legal rights. This manufacturer’s warranty is governed by the laws of the country in which you purchased your Belkin, Linksys or Wemo product. In many countries, consumers have rights under local consumer laws. Those consumer rights may differ between countries, states and provinces, and often cannot be excluded. Your local consumer rights organization can advise you on your legal rights. This manufacturer’s warranty is not intended to: • change or exclude any rights under consumer law that cannot be lawfully changed or excluded; or • limit or exclude any right you have against the person who sold the Belkin, Linksys or Wemo product to you if that person has breached their sales contract with you. WHAT DOES THIS WARRANTY COVER? Belkin warrants that the product hardware and any software media (i.e., media on which the product software is provided) will be free from defects in materials and workmanship under normal use during the Warranty Period described below. This means that the product won’t be defective, and that it will look and work as advertised during the relevant period. This warranty does not apply to products purchased from a source other than Belkin or a Belkin Authorized Reseller. How long is the product warranted? Belkin warrants that the hardware in this Belkin, Linksys or Wemo product, and any associated software media, will be free from defects in materials and workmanship under normal use during the Warranty Period. The Warranty Period begins on the date the product was purchas…

Text truncated - open the document above for the full version.

127.00 x 127.00 x 127.00 Business Unit: Program Manager: Packaging Engineer: Material: Blank Size (in): Side Shown: L x W x D (mm): DIE LAYOUT 0 Unit: Flute/Grain: REV FINAL PRINT SIDE 5 x 5 x 5 L x W x D (in): 5 [127.000] 5 [127.000] 14 15 / 16 [379.413] 5 [127.000] 4 15 / 16 [125.413] 4 15 / 16 [125.413] 5 [127.000] 5 [127.000] QSG - 128 GSM C2S ARTPAPER FRONT BACK Page 6 (Back)Page 5Page 1 (Cover) Page 3Page 4Page 2 IN/MM Drawing Scale 1:1 Retail Outside Dimension (Including Hang Tab) DO NOT PRINT DIE LINES, PRINTERS NOTES PRINT SPECS: LEGEND: 379.413 x 127 14+15/16 x 5 Die Line File: NET-Networking Brian Byrd Please refer to drawing FDL_MSKU_5 X 5_6 PAGE_TF_QSG Color Plates: Notes: Artwork File: horizontal 00 RELEASE DATE: 10/16/2018 Tolerance:+/- 1/32" - 0.8mm Blank Size (mm): Finish: DIELINE: THIS DOCUMENT & THE INFORMATION IN IT ARE THE CONFIDENTIAL PROPERTY OF BELKIN INTERNATIONAL AND MUST NOT BE COPIED, REPRODUCED OR USED IN ANY MANNER WITHOUT THE WRITTEN CONSENT OF BELKIN CORPORATION. IT MUST BE RETURNED UPON REQUEST This dieline works for following skus (if any): GLOSS AQ DIE/MATERIAL SPECS: Screen Glue Nitto Tape QSG_E7350-CA_8820-03016_RevA00_WiFi6_Router C Y M K ALL TEXT AND GRAPHIC ELEMENTS COLOR: CMYK Tri-Fold BACK COVER FRONT COVER INSIDE PAGE I N N O V A T I O N C R E A T I V E G R O U P 1 7 8 7 5 5 FILE NAME QSG_E7350-CA_8820-03016_RevA00_WiFi6_Router S K U # E7350-CA P# 8 820 - 03016 R E V A00 DESIGNER Shiho DATE 03/2 5/20 4: 36 PM VERSION 02 E7350 Quick Start Guide AX1800 Dual-Band WiFi 6 Router Routeur sans fil 6 double bande AX1800 Guide de démarrage rapide 8820-03016 Rev. A00 TIPS FOR SUCCESSFUL SETUP CONSEILS POUR UNE CONFIGURATION RÉUSSIE • Check that you have a working broadband internet connection by connecting a computer directly to your modem. Vérifiez que votre connexion Internet à large bande fonctionne correctement en connectant un ordinateur directement à votre modem. • Si vous ne pouvez pas vous connecter à internet après avoir configuré votre routeur, éteignez votre modem, votre routeur et votre ordinateur, puis redémarrez-les dans cet ordre. • For more tips, visit linksys.com/support/E7350 Pour obtenir d'autres conseils, consultez linksys.com/support/E7350. GET HELP OBTENEZ DE L'AIDE Internet: linksys.com/support/E7350 Twitter: @LinksysCares Phone (US/Canada): 800-326-7114 (complimentary support during your warranty period) Téléphone (États-Unis/Canada) : 800-326-7114 (soutien gratuit pendant la période de garantie) AS YOU COMPLETE SETUP, RECORD YOUR ROUTER SETTINGS HERE NOTEZ ICI LES PARAMÈTRES DE VOTRE ROUTEUR AU FUR ET À MESURE DE LA CONFIGURATION 2.4 GHz Wi-Fi name (SSID) Nom du réseau sans-fil 2,4 GHz (SSID) 2.4 GHz Wi-Fi password Mot de passe du réseau sans-fil 2,4 GHz 5 GHz Wi-Fi name (SSID) Nom du réseau sans-fil 5 GHz (SSID) 5 GHz Wi-Fi password Mot de passe du réseau sans-fil 5 GHz Router password (default is “admin”) Mot de passe du routeur (« admin » par défaut) Connectez-vous au nom de réseau sans fil sécurisé dont le nom est indiqué sur l'étiquette. (Vous pourrez modifier ces renseignements ultérieurement.) Sélectionnez l'option permettant de se connecter automatiquement à ce réseau à l'avenir. Vous n'aurez pas accès à Internet tant que le routeur n'aura pas été intégralement configuré (voir Étape 5). Connect to the secure Wi-Fi name shown on the sticker. (You can change these details later.) Select the option to automatically connect to this network in the future. You will not have internet access until you complete router setup (see Step 5). Once you are finished with setup, please be sure to register your router so we can keep you informed about security updates, product recalls and other things that will improve your experience. Une fois que vous avez terminé la configuration, n'oubliez pas d'enregistrer votre routeur afin que nous puissions vous tenir informé des mises à jour de sécurité, des rappels de produits et d'autres éléments qui vous aideront à profiter d'une meilleure expérience. Enter http://myrouter.local in a web browser. Follow the on-screen instructions to complete your router setup. You also can type 192.168.1.1 in a browser to start setup. Entrez http://myrouter.local dans un navigateur Web. Suivez les directives à l'écran pour terminer la configuration. Vous pouvez également entrer 192.168.1.1 dans un navigateur pour commencer la configuration. 4 6 5 Place sticker here Wi-Fi Name/Wi-Fi Password Placez l'étiquette autocollante ici Nom du réseau sans-fil/Mot de passe du réseau sans-fil http://myrouter.local ModemRouter Modem - Router (Gateway) <modem and gateway> ModemRouter Modem - Router (Gateway) Where does your internet come from? D'où vient votre connexion Internet? Modem et routeur séparés Modem Routeur-Modem Modem-Router If you have a separate modem and router, disconnect and remove your old router. Plug one end of the included ethernet cable into the yellow Internet port on your new router. If you have a modem, plug the other end into the Ethernet (LAN) port on the modem. OR OR OU OU If you have a modem-router, leave it connected. Plug one end of the included ethernet cable to the yellow Internet port on your new router. If you have a modem- router, plug the other end into any available port. 1 Plug the router into a power source. Branchez le routeur à une source d'alimentation. 2 Connect your new router to your modem or modem-router. Raccordez votre nouveau routeur à votre modem ou routeur-modem. 3 BA ModemRouter Routeur Modem - Router (Gateway) Routeur-Modem (Passerelle) Si vous avez un modem et un routeur séparés, déconnectez votre ancien routeur et retirez celui-ci. Si vous avez un routeur-modem, laissez-le connecté. Si vous avez un routeur-modem, branchez l'autre extrémité dans tout port disponible. Si vous avez un modem, branchez l'autre extrémité dans le port ethernet (LAN) sur le modem. ModemRouteur-Modem Separate Modem and Router Modem-Router B A K8820-03016(YT)

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-06 -18 FCC ID: K7S-03535 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description Operational Description-Antenna Specification The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Po-Wen Cheng Belkin International, Inc. Tel: 949-238-4518 Fax: N/A E-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-06-17 FCC ID: K7S-03535 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Po-Wen Cheng Belkin International, Inc. Te l : 949-238-4518 Fax: N/A E-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-06-18 FCC ID: K7S-03535 A U T H O R I Z A T I O N L E T T E R To whom it may concern: I, the undersigned Jay Tu of Belkin International, Inc. hereby authorize Po-Wen Cheng of Belkin International, Inc. to act on my behalf in all matters relating to all processes required in FCC and any communication needed with the national authority. Any and all acts carried out by Po-Wen Cheng on my behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, -------------- Jay Tu / Manager, Regulatory Compliance Belkin International, Inc. +1 310 633 9309*9142 e-mail: [email protected]

Reference No.: 200514E05-1 Page 1/12 CONSTRUCTION PHOTOS OF EUT Reference No.: 200514E05-1 Page 2/12 Reference No.: 200514E05-1 Page 3/12 Reference No.: 200514E05-1 Page 4/12 Reference No.: 200514E05-1 Page 5/12 Adapter- WB-24J12FU Reference No.: 200514E05-1 Page 6/12 Adapter- WB-24J12R Reference No.: 200514E05-1 Page 7/12 Reference No.: 200514E05-1 Page 8/12 Reference No.: 200514E05-1 Page 9/12 Adapter- KSA-24W-120200HU Reference No.: 200514E05-1 Page 10/12 Reference No.: 200514E05-1 Page 11/12 Adapter- KSA-24W-120200D5 Reference No.: 200514E05-1 Page 12/12

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094

Reference No.: 200514E05-2 Page 1/16 CONSTRUCTION PHOTOS OF EUT Reference No.: 200514E05-2 Page 2/16 Reference No.: 200514E05-2 Page 3/16 Reference No.: 200514E05-2 Page 4/16 Reference No.: 200514E05-2 Page 5/16 Reference No.: 200514E05-2 Page 6/16 Reference No.: 200514E05-2 Page 7/16 Reference No.: 200514E05-2 Page 8/16 Reference No.: 200514E05-2 Page 9/16 Antenna-DB1 Reference No.: 200514E05-2 Page 10/16 Reference No.: 200514E05-2 Page 11/16 Antenna- DB2 Reference No.: 200514E05-2 Page 12/16 Reference No.: 200514E05-2 Page 13/16 Antenna- DFS ANT (RX only) Reference No.: 200514E05-2 Page 14/16 Reference No.: 200514E05-2 Page 15/16 Antenna- BT ANT Reference No.: 200514E05-2 Page 16/16

Report No.: SA200514E05 Page No. 1 / 7 Report Format Version: 6.1.1 Reference No.: RF Exposure Report Report No.: SA200514E05 FCC ID: K7S-03535 Test Model: E7350 Received Date: May 14, 2020 Test Date: June 05, 2020 Issued Date: June 18, 2020 Applicant: Belkin International, Inc. Address: 12045 East Waterfront Dr. Playa Vista California United States 90094 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA200514E05 Page No. 2 / 7 Report Format Version: 6.1.1 Reference No.: Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Antenna Gain ...................................................................................................................................... 6 2.5 Calculation Result ............................................................................................................................... 7 Report No.: SA200514E05 Page No. 3 / 7 Report Format Version: 6.1.1 Reference No.: Release Control Record Issue No. Description Date Issued SA200514E05 Original release. June 18, 2020 Report No.: SA200514E05 Page No. 4 / 7 Report Format Version: 6.1.1 Reference No.: 1 Certificate of Conformity Product: AX1800 Dual-Band WiFi 6 Router Brand: Linksys Test Model: E7350 Sample Status: ENGINEERING SAMPLE Applicant: Belkin International, Inc. Test Date: June 05, 2020 Standards: FCC Part 2 (Section 2.1091) IEEE C95.3 -2002 References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: June 18, 2020 Joyce Kuo / Specialist Approved by : , Date: June 18, 2020 Clark Lin / Technical Manager Report No.: SA200514E05 Page No. 5 / 7 Report Format Version: 6.1.1 Reference No.: 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz ; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 35 cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200514E05 Page No. 6 / 7 Report Format Version: 6.1.1 Reference No.: 2.4 Antenna Gain Antenna NO. Model Antenna Net Gain(dBi) Frequency range Antenna Type Connector Type Cable Length (mm) DB1 Galtronics 3.4 2.4~2.4835GHz PCB i-pex(MHF) 58 3.99 5.15~5.25GHz 4.17 5.25~5.35GHz 4.74 5.47~5.725GHz 5.24 5.725~5.85GHz DB2 Galtronics 3.45 2.4~2.4835GHz PCB i-pex(MHF) 68 3.52 5.15~5.25GHz 3.00 5.25~5.35GHz 3.08 5.47~5.725GHz 3.11 5.725~5.85GHz DFS Ant (RX only) Galtronics 2.14 5.15~5.25GHz metal none N/A 2.86 5.25~5…

Text truncated - open the document above for the full version.

Report No.: RF200514E05-2 Page No. 1 / 53 Report Format Version: 6.1.1 Reference No.: FCC Test Report (BT-EDR) Report No.: RF200514E05-2 FCC ID: K7S-03535 Test Model: E7350 Received Date: May 14, 2020 Test Date: June 01 to 10, 2020 Issued Date: June 18, 2020 Applicant: Belkin International, Inc. Address: 12045 East Waterfront Dr. Playa Vista California United States 90094 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF200514E05-2 Page No. 2 / 53 Report Format Version: 6.1.1 Reference No.: Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT (BT-EDR) ................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Duty Cycle of Test Signal .................................................................................................................. 12 3.4 Description of Support Units ............................................................................................................. 13 3.4.1 Configuration of System under Test .................................................................................................. 14 3.5 General Description of Applied Standards and References ............................................................. 15 4 Test Types and Results ...................................................................................................................... 16 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 16 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 16 4.1.2 Test Instruments ................................................................................................................................ 17 4.1.3 Test Procedures ................................................................................................................................. 19 4.1.4 Deviation from Test Standard ............................................................................................................ 19 4.1.5 Test Setup .......................................................................................................................................... 20 4.1.6 EUT Operating Conditions ................................................................................................................. 21 4.1.7 Test Results ....................................................................................................................................... 22 4.2 Conducted Emission Measurement .................................................................................................. 30 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 30 4.2.2 Test Instruments ................................................................................................................................ 30 4.2.3 Test Procedures ................................................................................................................................. …

Text truncated - open the document above for the full version.

Report No.: RF200514E05-4 Page No. 1 / 29 Report Format Version: 6.1.2 Reference No.: 191227E08 Supplemental “Transmit Simultaneously” Test Report Report No.: RF200514E05-4 FCC ID: K7S-03535 Test Model: E7350 Received Date: May 14, 2020 Test Date: June 01 to 05, 2020 Issued Date: June 18, 2020 Applicant: Belkin International, Inc. Address: 12045 East Waterfront Dr. Playa Vista California United States 90094 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compl…

Text truncated - open the document above for the full version.