K7S-03580Velop AX4200 WiFi 6 System

Regulatory and Warranty Information VELOP WHOLE HOME WI-FI FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and devices. • Connect the equipment to an outlet other than the receiver’s. • Consult a dealer or an experienced radio/TV technician for assistance. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radio Frequency 2.4GHz band operation of this product in the USA is firmware-limited to channels 1 through 11. Selection of other channels is not possible The device for the Radio Frequency band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 38 cm between the radiator and your body. This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Wireless Disclaimer The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions. Safety Notices English WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: This product may contain chemicals, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. WARNING: The power adaptor is the equipment ́s disconnection device. The power outlet must be located nearby the equipment and its access must be easy. Español ADVERTENCIA: No use este producto cerca del agua, por ejemplo en un sotano húmedo o cerca de una piscina. ADVERTENCIA: Evite usar este producto durante una tormenta eléctrica. Puede existir el riesgo remoto de que se produzca una descarga eléctrica producida por un rayo. ADVERTENCIA: El adaptador de alimentación es el dispositivo de desconexión del equipo. La base de toma de corriente debe estar cerca del equipo y ser fácilmente accessible. Third-Party Software or Firmware The use of software or firmware not supported/provided by Linksys products may result that the equipment is no longer compliant with the regulatory requirements. Technical Documents on www.linksys.com Follow these steps to access technical documents: • Enter www.linksys.com in your web browser. • Select the country or region in which you live. • Click the Support tab. • Type the model number or keyword. • Select Downloads from the list of tabs. • Select the version of product. • Click on the document you want and it will open in PDF format if you have Adobe Reader installed on your computer. • WEB: For additional information, please visit http://linksys.com WARRANTY AND SUPPORT INFORMATION IMPORTANT! PLEASE RETAIN PROOF OF PURCHASE AND PRODUCT WARRANTY INFORMATION LIMITED WARRANTY (UNITED STATES AND CANADA) This warranty is provided to you by Belkin International, Inc, or one of its subsidiaries or affiliates (“Belkin”) IMPORTANT NOTICE REGARDING YOUR CONSUMER RIGHTS The benefits we give in this manufacturer’s warranty are additional to any rights and remedies that you may have under local consumer protection laws. Nothing in this warranty limits or affects your legal rights. This manufacturer’s warranty is governed by the laws of the country in which you purchased your Belkin, Linksys or WeMo product. In many countries, consumers have rights under local consumer laws. Those consumer rights may differ between countries, states and provinces, and often cannot be excluded. Your local consumer rights organization can advise you on your legal rights. This manufacturer’s warranty is not intended to: • change or exclude any rights under consumer law that cannot be lawfully changed or excluded; or limit or exclude any right you have against the person who sold the Belkin, Linksys or WeMo product to you if that person has breached their sales contract with you. WHAT DOES THIS WARRANTY COVER? Belkin warrants that the product hardware and any software media (i.e., media on which the product software is provided) will be free from defects in materials and workmanship under normal use during the Warranty Period described below. This means that…

Text truncated - open the document above for the full version.

1 z USER GUIDE VELOP AX4200 Model MX4200/MX4000/MX4200C/MX4050 2 Table of Contents Product Overview ___________________________________________________________________________________________ 3 Front/top ______________________________________________________________________________________________________ 3 Back ____________________________________________________________________________________________________________ 4 Bottom _________________________________________________________________________________________________________ 5 Where to find more help ____________________________________________________________________________________ 6 Set Up _________________________________________________________________________________________________________ 7 Velop System Settings ______________________________________________________________________________________ 9 Log in to the Linksys app ____________________________________________________________________________________ 9 Dashboard ___________________________________________________________________________________________________ 10 Devices _______________________________________________________________________________________________________ 11 To view or change device details ____________________________________________________________________________________ 12 Wi-Fi Settings _______________________________________________________________________________________________ 12 Advanced Settings ____________________________________________________________________________________________________ 14 Connect a Device with WPS _________________________________________________________________________________________ 15 Guest Access _________________________________________________________________________________________________ 16 External Storage ____________________________________________________________________________________________ 17 Speed Check _________________________________________________________________________________________________ 19 Parental Controls ___________________________________________________________________________________________ 20 Device Prioritization _______________________________________________________________________________________ 21 Notifications _________________________________________________________________________________________________ 22 Velop Administration ______________________________________________________________________________________ 23 Advanced Settings __________________________________________________________________________________________ 25 Internet Settings ______________________________________________________________________________________________________ 25 Port Settings __________________________________________________________________________________________________________ 26 Wi-Fi MAC Filters ____________________________________________________________________________________________________ 27 My Account __________________________________________________________________________________________________ 28 Feedback _____________________________________________________________________________________________________ 29 Help ___________________________________________________________________________________________________________ 30 Connect Directly To Velop _______________________________________________________________________________ 31 Velop admin password ______________________________________________________________________________________________ 32 How to restore factory defaults ________________________________________________________________________ 33 Specifications ______________________________________________________________________________________________ 34 Linksys Velop _______________________________________________________________________________________________ 34 Environmental ______________________________________________________________________________________________ 34 3 Product Overview Front/top The light on the top of your node gives you information about the node’s operation. Light description Status Blinking blue Starting up Solid blue Connected Blinking purple Setup in progress Solid purple Ready for setup Blinking red Disconnected  Child node: too far  Parent node: unplugged from modem Solid red No internet from the modem Solid yellow Weak connection  Child node only 4 Back USB 3.0 port— Connect and share USB drives on your network. For local file sharing only (no FTP, media server or virtualUSB support). Also, not intended for sharing peripherals such as printers, scanners or cameras. Ethernet ports—Connect ethernet cables to these Gigabit ethernet (10/100/1000) ports and to other wired devices on your network. If you have more than one node in your Velop system, use one of these ports to connect to your modem or modem-router. Note—For best performance, use a CAT5e or higher rated cable on the Ethernet port. Internet port—Connect an ethernet cable to the yellow gigabit (10/100/1000) port, and to a broadband internet cable/DSL or fiber modem. If you are using this router as a child node in a mesh Wi-Fi system, you can use this port to create a wired connection to another node. Power port—Connect the included AC power adapter to this port. 5 Bottom Reset button—Press and hold until the light on top of the node turns red, fades and flashes bright red again to reset the node to its factory defaults. Wi-Fi Protected Setup button—Press to connect WPS-enabled network devices. Power switch—Slide to | (on) to power on the node. 6 Help Where to find more help  Linksys.com/support/Velop  Linksys app help (launch the app and click Help in the main navigation menu) Note—Licenses and notices for third party software used in this product may be viewed on http://support.linksys.com/en-us/license. Please contact http://support.linksys.com/en-us/gplcodecenter for questions or GPL source code requests. 7 Set Up IMPORTANT—Velop nodes can be set up as p…

Text truncated - open the document above for the full version.

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-07 -01 FCC ID: K7S-03580 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Po-Wen Cheng Belkin International, Inc. Tel: 949-238-4518 E-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-07-01 FCC ID: K7S-03580 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Po-Wen Cheng Belkin International, Inc. Tel: 949-238-4518 E-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-07-01 FCC ID: K7S-03580 AUTHORIZATION LETTER To Whom It May Concern: Belkin International, Inc. hereby authorizes Debby Lin / Senior specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Debby Lin / Senior specialist of BV CPS Taoyuan on Belkin International, Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Po-Wen Cheng Belkin International, Inc. Tel: 949-238-4518 E-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Dr. Playa Vista California United States 90094 Date: 2020-07-02 A U T H O R I Z A T I O N L E T T E R To whom it may concern: I, the undersigned Jay Tu of Belkin International, Inc. hereby authorize Po-Wen Cheng of Belkin International, Inc. to act on my behalf in all matters relating to all processes required in FCC and any communication needed with the national authority. Any and all acts carried out by Po-Wen Cheng on my behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, --------- Jay Tu / Manager, Regulatory Compliance Belkin International, Inc. Tel: +1 310 633 9309*9142 E-mail: [email protected]

Reference No.:200603E15-1 Page 1/10 CONSTRUCTION PHOTOS OF EUT Reference No.:200603E15-1 Page 2/10 Reference No.:200603E15-1 Page 3/10 Reference No.:200603E15-1 Page 4/10 Reference No.:200603E15-1 Page 5/10 Model No.: WA-36N12R Reference No.:200603E15-1 Page 6/10 Reference No.:200603E15-1 Page 7/10 Model No.: WA-36N12FU Reference No.:200603E15-1 Page 8/10 Reference No.:200603E15-1 Page 9/10 Model No.: MU36B1120300-A1 Reference No.:200603E15-1 Page 10/10

Label Location FCC ID : K7S-03580 IC : 3623A-03580 Label Here

MX4050 1 ZONE RELEASE EDWARD SU08/16/19 WNC CONFIDENTIAL 1 CATHY CHEN 08/16/19 08/16/19 CATHY CHEN 08/16/19 EDWARD SU A3 2 0.2 A B A B 12 4L.XXXXXXXX LABEL,PRODUCT MX4050 US, SAQB-L1 REEL DIRECTION LINKSYS SDGY1604_D90 ON-LINE PRINT DIE CUT TEST ITEMTEST SPECTEST CONDITIONCRITERIA 1 附著力測試 ISO Class.: 1 ASTM Class.: 4 B ASTM D3359-02/ ISO 2409:2007 Detach ment of small flake s of the co ating at the interse ct ions of the cu ts. A cr oss-cu t area not si gnifica ntly greater than 5% is affect ed. ( PPATM(T)(30)(N)J), 9. *Ø9.20±0.2 *Ø7.60 ±0.2 15.85±0.1 *80.59 0 -0.4 R5.32 ,4PLS 0 -0.4 62.70 *80.59 0 -0.4 7.10 +0.3 -0 8.60 +0.3 -0 9.50±0.1 60.35 0 -0.4 R1.30 4.30±0.1 0 -0.4 _V elopSetupXXX XXXXXXXXXX 12345 XXXXXXXXXXXX 38U10M3MYXXXXX NOTES: 1. MATERIAL: WHITE MATT PET, T=0.1±0.003,(HTLW100(EB)J) FINISH: PP COATING, T=0.025±0.003,0.003, ADHESIVE: EMBOSSED ADHESIVE, T=0.035±0.003 2. COLOR: a. BACKGROUND=PET ORIGINAL COLOR (WHITE) b. PRINTING= LINKSYS SDGY1604_D90(201801003) 3.離型紙左右間距各3 ± 0.5 mm上下間距各3 ± 0.3 mm 4. 5.TEMPERATURE RESISTANT= 120 0 C. 6.UL APPROVAL PGJI2,CM-100-KPTRICOH B110C,B110CR,B110CW 7.:30mm~120mm±0.4mm,120~315mm±0.5mm,315±0.8mm 8.TEST REQUIREMENTS 5.5 ± 0.5 16 ± 0.5 *1 *2 *3 *4 5 6 7 8 9 10 11 12 13 14 15

Reference No.:200603E15-2 Page 1/35 CONSTRUCTION PHOTOS OF EUT Reference No.:200603E15-2 Page 2/35 Reference No.:200603E15-2 Page 3/35 Reference No.:200603E15-2 Page 4/35 Reference No.:200603E15-2 Page 5/35 Reference No.:200603E15-2 Page 6/35 Reference No.:200603E15-2 Page 7/35 Reference No.:200603E15-2 Page 8/35 Reference No.:200603E15-2 Page 9/35 Reference No.:200603E15-2 Page 10/35 Reference No.:200603E15-2 Page 11/35 Reference No.:200603E15-2 Page 12/35 Reference No.:200603E15-2 Page 13/35 Reference No.:200603E15-2 Page 14/35 Reference No.:200603E15-2 Page 15/35 Reference No.:200603E15-2 Page 16/35 Reference No.:200603E15-2 Page 17/35 Reference No.:200603E15-2 Page 18/35 Reference No.:200603E15-2 Page 19/35 Reference No.:200603E15-2 Page 20/35 Reference No.:200603E15-2 Page 21/35 Reference No.:200603E15-2 Page 22/35 Reference No.:200603E15-2 Page 23/35 Reference No.:200603E15-2 Page 24/35 WIFi LB_1 Ant. (Dual A) Reference No.:200603E15-2 Page 25/35 Reference No.:200603E15-2 Page 26/35 WIFi LB_2 Ant. (Dual B) Reference No.:200603E15-2 Page 27/35 Reference No.:200603E15-2 Page 28/35 WIFi HB_1 Ant. (5/6G A) & WIFi HB_2 Ant. (5/6G B) Reference No.:200603E15-2 Page 29/35 Reference No.:200603E15-2 Page 30/35 Reference No.:200603E15-2 Page 31/35 WIFi HB_3 Ant. (5/6G C) & WIFi HB_4 Ant. (5/6G D) Reference No.:200603E15-2 Page 32/35 Reference No.:200603E15-2 Page 33/35 Reference No.:200603E15-2 Page 34/35 BT Ant. Reference No.:200603E15-2 Page 35/35

Report No.: SA200603E15 Page No. 1 / 7 Report Format Version: 6.1.1 Reference No.: 200603E15 RF Exposure Report Report No.: SA200603E15 FCC ID: K7S-03580 Test Model: MX4200 Series Model: MX4050, MX4000, MX4200C Received Date: June 03, 2020 Test Date: July 01 to 02, 2020 Issued Date: July 17, 2020 Applicant: Belkin International, Inc. Address: 12045 East Waterfront Drive Playa Vista, CA. 90094, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Ta i w a n Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Ta i w a n FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA200603E15 Page No. 2 / 7 Report Format Version: 6.1.1 Reference No.: 200603E15 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Antenna Gain ...................................................................................................................................... 6 2.5 Calculation Result of Maximum Conducted Power ............................................................................. 7 Report No.: SA200603E15 Page No. 3 / 7 Report Format Version: 6.1.1 Reference No.: 200603E15 Release Control Record Issue No. Description Date Issued SA200603E15 Original release. July 17, 2020 Report No.: SA200603E15 Page No. 4 / 7 Report Format Version: 6.1.1 Reference No.: 200603E15 1 Certificate of Conformity Product: Velop AX4200 WiFi 6 System Brand: Linksys Test Model: MX4200 Series Model: MX4050, MX4000, MX4200C Sample Status: ENGINEERING SAMPLE Applicant: Belkin International, Inc. Test Date: July 01 to 02, 2020 Standards: FCC Part 2 (Section 2.1091) IEEE C95.3 -2002 References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date:July 17, 2020 Phoenix Huang / Specialist Approved by : , Date:July 17, 2020 Clark Lin / Technical Manager Report No.: SA200603E15 Page No. 5 / 7 Report Format Version: 6.1.1 Reference No.: 200603E15 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz ; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 38 cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200603E15 Page No. 6 / 7 Report Format Version: 6.1.1 Reference No.: 200603E15 2.4 Antenna Gain Ant. No. Transmitter Circuit Ant.Net Gain (dBi) Freq. Range (GHz) Ant. Type Connector Type WIFi LB_1 Dual A 3.1 2.4~2.4835 PCB i-pex(MHF) 3.5 5.15~5.25 5 5.25~5.35 3.7 5.47~5.725 4.6 5.725~5.85 WIFi LB_2 Dual B 2.8 2.4~2.4835 PCB i-pex(MHF) 4.8 5.15~5.25 5.1 5.25~5.35 5 5.47~5.725 4.7 5.725~5.85 WIFi HB_…

Text truncated - open the document above for the full version.

Report No.: RF200603E15-2 Page No. 1 / 29 Report Format Version: 6.1.2 Reference No.: 200603E15 Supplemental “Transmit Simultaneously” Test Report Report No.: RF200603E15-2 FCC ID: K7S-03580 Test Model: MX4200 Series Model: MX4050, MX4000, MX4200C Received Date: June 03, 2020 Test Date: June 26 to July 02, 2020 Issued Date: July 17, 2020 Applicant: Belkin International, Inc. Address: 12045 East Waterfront Drive Playa Vista, CA. 90094, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Ta i w a n Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Ta i w a n FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim any endorsement by TAF. Report No.: RF200603E15-2 Page No. 2 / 29 Report Format Version: 6.1.2 Reference No.: 200603E15 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.1.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.2 Description of Support Units ............................................................................................................. 12 3.2.1 Configuration of System under Test .................................................................................................. 13 4 Test Types and Results ...................................................................................................................... 14 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 14 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 14 4.1.2 Test Instruments ................................................................................................................................ 15 4.1.3 Test Procedures ................................................................................................................................. 16 4.1.4 Deviation from Test Standard ............................................................................................................ 17 4.1.5 Test Setup .......................................................................................................................................... 17 4.1.6 EUT Operating Conditions ................................................................................................................. 18 4.1.7 Test Results ....................................................................................................................................... 19 4.2 Conducted Emission Measurement .........................…

Text truncated - open the document above for the full version.