K7SF7C031WeMo Link

The following paragraphs are required by the FCC and prove that this product meets all regulatory limits with regard to radio interference and radiation exposure. If you use this product as intended you will have no issues with either. FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin International, Inc., of 12045 E. Waterfront Drive, Playa Vista, CA 90094, declare under our sole responsibility that the product, F5Z0489, to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the distance between the equipment and the receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement / Avis d’Industrie Canada This digital apparatus complies with CAN ICES-3(B). Cet appareil numérique conforme à la norme NMB-3(B) du Canada. This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. INFoRmAtIoN to USER oF WEmo SmARt LED BULBS: this device is not intended for use with emergency exits. Not for use with dimmers. Do not use where directly exposed to water. AvIS AUx UtILISAtEURS D’AmpoULES DEL INtELLIgENtES WEmo: Ce produit n’est pas destiné à être utilisé pour les sorties d’urgence. Ne convient pas pour une utilisation avec variateur. Ne pas utiliser dans les endroits directement exposés à l’eau. INFoRmAtIoN to USER oF WEmo LINk: Use indoors and in dry location only this product may only be plugged in to socket outlets that are easily accessible AvIS AUx UStILISAtEURS DU LIEN WEmo: pour usage à l’intérieur et dans des endroits secs seulement. Ce produit ne doit être branché que sur des prises de courant faciles d’accès. 8820fc01933 Rev. A01 0.00 x 0.00 x 0.00 Business Unit: Program Manager: Packaging Engineer: Material: Blank Size (in): Side Shown: L x W x D (mm): DIE LAYOUT 0 Unit: Flute/Grain: REV Intermediate PRINT SIDE 0 x 0 x 0 L x W x D (in): 8 Pt. SBS 80 gsm wood free paper 16 pt PET 2 7 / 8 [73.025] 3 3 / 8 [86.005] 23 [584.200] 8 3 / 16 [207.962] 7 [177.800] 14 19 / 32 [370.681] 3 1 / 4 [82.550] Front Back 8 7 / 8 [225.425] 8 3 / 8 [212.883] FrontBack IN/MM Drawing Scale 1:1 Retail Outside Dimension (Including Hang Tab) DO NOT PRINT DIE LINES, PRINTERS NOTES PRINT SPECS: DIE/MATERIAL SPECS: 1202.630 x 593.725 47.348 x 23+3/8 Die Line File: Core Matthew Duffy-LR SBS-24/.61mm/400g C1S IDL_MSKU_DUAL CHARGE N SYNC DOCKS Color Plates: Notes: Artwork File: horizontal 00 RELEASE DATE: 5/16/2014 Tolerance:+/- 1/32" - 0.8mm Blank Size (mm): Finish: DIELINE: THIS DOCUMENT & THE INFORMATION IN IT ARE THE CONFIDENTIAL PROPERTY OF BELKIN INTERNATIONAL AND MUST NOT BE COPIED, REPRODUCED OR USED IN ANY MANNER WITHOUT THE WRITTEN CONSENT OF BELKIN CORPORATION. IT MUST BE RETURNED UPON REQUEST This dieline works for following skus (if any): F8J136; F8J137 0.00 x 0.00 x 0.00 Business Unit: Program Manager: Packaging Engineer: Material: Blank Size (in): Side Shown: L x W x D (mm): DIE LAYOUT 0 Unit: Flute/Grain: REV Intermediate PRINT SIDE 0 x 0 x 0 L x W x D (in): 8 Pt. SBS 80 gsm wood free paper 16 pt PET 2 7 / 8 [73.025] 3 3 / 8 [86.005] 23 [584.200] 8 3 / 16 [207.962] 7 [177.800]…

Text truncated - open the document above for the full version.

Date: 1/21/2014 Subject: Ad Hoc Mode Function Declaration FCC ID: K7SF7C031 To Whom it may concern, This device is acting as master and operating on 2.4GHz band. Ad Hoc function is available on client mode and not able to work on non-US frequencies. Please contact the one signed below or the authorized agent for this filing. Thank you. Regards, (Signature Here) Daniel Wesey / Manager, Global Regulatory Compliance Engineering Belkin, International Inc., Tel No.:1-310-751-2816 Fax No.: 1-310-751-5912 E-mail: [email protected]

Date: 2014-07-07 FCC ID: K7SF7C031 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until Sep 30, 2014 in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Daniel Wesey / Manager, Global Engineering Services Belkin, International Inc., Tel No.:1-310-751-2816 Fax No.: 1-310-751-5912 E-mail: [email protected]

Date: 1/3/2014 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: K7SF7C031 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematic Diagram Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------------------ Daniel Wesey /Manager, Global Regulatory Compliance Engineering Belkin, International Inc., Tel No.:1-310-751-2816 Fax No.: 1-310-751-5912 E-mail: [email protected]

Power of Attorney Date: January 21, 2014 FCC ID: K7SF7C031 To whom it may concern: We, the undersigned Belkin, International Inc., hereby authorize Bureau Veritas Consumer Products Services (H.K) Ltd., Taoyuan Branch. of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by Bureau Veritas Consumer Products Services (H.K) Ltd., Taoyuan Branch. on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Daniel Wesey/Manager, Global Regulatory Compliance Engineering Belkin, International Inc., Tel No.:1-310-751-2816 Fax No.: 1-310-751-5912 E-mail: [email protected]

Report No.: 131128E01 1 of 6 CONSTRUCTION PHOTOS OF EUT Report No.: 131128E01 2 of 6

(Fig.1) FCC ID: K7SF7C031 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. 1 OF1 1/1 DRAWN APVD SANDY CHEN BELKIN IDG 10/15/13 10/15/13 0.15mm 0.5mm 1mm 2014-03-12 RELEASE TO FILE DESCRIPTIONREV DATE APPROVED F AW,COVER,SHR1-L1 A4 A PART NUMBER COLOR 1 印刷尺寸公差 其他 886-3-6667322 Laser Adjusted 25mA to “50 mA” REVISIONS KENVIN HUANG 3PSHR100101-111 3PSHR100101-111 3.0 3

Report No.: 131128E01 3 of 6 Report No.: 131128E01 4 of 6 Report No.: 131128E01 5 of 6 Report No.: 131128E01 6 of 6

Report No.: SA131128E01 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA131128E01 MODEL NO.: F7C031 FCC ID: K7SF7C031 RECEIVED: Nov. 28, 2013 TESTED: Apr. 01 and May 02, 2014 ISSUED: June 12, 2014 APPLICANT: Belkin, International Inc., ADDRESS: 12045 East Waterfront Drive Playa Vista, California 90094 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA131128E01 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT ............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. ANTENNA GAIN ...................................................................................................... 5 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .......................... 6 Report No.: SA131128E01 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA131128E01 Original release June 12, 2014 Report No.: SA131128E01 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: WeMo Link BRAND NAME: Belkin MODEL NO.: F7C031 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Belkin, International Inc., TESTED DATE: Apr. 01 and May 02, 2014 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: F7C031) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Nov. 19, 2013 ( Lori Chung, Specialist ) APPROVED BY : , DATE:Nov. 19, 2013 ( May Chen, Manager ) Report No.: SA131128E01 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 5. ANTENNA GAIN The antennas provided to the EUT, please refer to the following table: Zigbee Antenna Spec. Brand Antenna Type Antenna ConnectorGain(dBi)Frequency range (MHz) WNC PIFA i-pex(MHF) 2.17 2400 – 2483.5 WLAN Antenna Spec. Brand Antenna Type Antenna ConnectorGain(dBi)Frequency range (MHz) WNC PIFA i-pex(MHF) 1.40 2400 – 2483.5 Report No.: SA131128E01 6 of 6 Report Format Version 5.0.0 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For WLAN FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 399.025 1.40 20 0.10958 1 For Zigbee FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2405 - 2475 95.719 2.17 20 0.03139 1.00 CONCLUSION: Both of the WLAN and Zigbee can transmit simultaneously, the formula of calculated the MPE is: CPD 1 / LPD 1 + CPD 2 / LPD 2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density Therefore, the worst-case situation is 0.10958 / 1 + 0.03139 / 1= 0.141, which is less than “1”. This confirmed that the device comply with FCC 1.1310 MPE limit. --- END ---

Report No.: RF131128E01 1 of 72 Report Format Version 5.2.0 FCC TEST REPORT (WLAN) REPORT NO.: RF131128E01 MODEL NO.: F7C031 FCC ID: K7SF7C031 RECEIVED: Nov. 28, 2013 TESTED: Dec. 09, 2013 to Apr. 03, 2014 ISSUED: June 12, 2014 APPLICANT: Belkin, International Inc., ADDRESS: 12045 East Waterfront Drive Playa Vista, California 90094 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF131128E01 2 of 72 Report Format Version 5.2.0 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 4 1. CERTIFICATION ...................................................................................................... 5 2. SUMMARY OF TEST RESULTS .............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 7 3. GENERAL INFORMATION ....................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT (WLAN) ........................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 13 3.4 DUTY CYCLE OF TEST SIGNAL ........................................................................... 14 3.5 DESCRIPTION OF SUPPORT UNITS ................................................................... 15 3.6 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 15 4. TEST TYPES AND RESULTS ................................................................................ 16 4.1 CONDUCTED EMISSION MEASUREMENT ......................................................... 16 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 16 4.1.2 TEST INSTRUMENTS ........................................................................................... 16 4.1.3 TEST PROCEDURES ............................................................................................ 17 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 17 4.1.5 TEST SETUP ......................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 18 4.1.7 TEST RESULTS ..................................................................................................... 19 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 21 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 21 4.2.2 TEST INSTRUMENTS ........................................................................................... 22 4.2.3 TEST PROCEDURES ............................................................................................ 26 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 26 4.2.5 TEST SETUP ......................................................................................................... 27 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 27 4.2.7 TEST RESULTS (MODE 1) .................................................................................... 28 4.2.8 TEST RESULTS (MODE 2) .................................................................................... 41 4.3 6dB BANDWIDTH MEASUREMENT ..................................................................... 54 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 54 4.3.2 TEST INSTRUMENTS ........................................................................................... 54 4.3.3 TEST PROCEDURE .............................................................................................. 54 4.3.4 DEVIATION FROM TEST STANDARD .....................…

Text truncated - open the document above for the full version.

Report No.: RF131128E01-1 1 of 47 Report Format Version 5.2.0 FCC TEST REPORT (Zigbee) REPORT NO.: RF131128E01-1 MODEL NO.: F7C031 FCC ID: K7SF7C031 RECEIVED: Nov. 28, 2013 TESTED: Dec. 09, 2013 to May 02, 2014 ISSUED: June 12, 2014 APPLICANT: Belkin, International Inc., ADDRESS: 12045 East Waterfront Drive Playa Vista, California 90094 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF131128E01-1 2 of 47 Report Format Version 5.2.0 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 4 1. CERTIFICATION ...................................................................................................... 5 2. SUMMARY OF TEST RESULTS .............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 7 3. GENERAL INFORMATION ....................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT (Zigbee) .......................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 13 3.4 DUTY CYCLE OF TEST SIGNAL ........................................................................... 13 3.5 DESCRIPTION OF SUPPORT UNITS ................................................................... 14 3.6 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 14 4. TEST TYPES AND RESULTS ................................................................................ 15 4.1 CONDUCTED EMISSION MEASUREMENT ......................................................... 15 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 15 4.1.2 TEST INSTRUMENTS ........................................................................................... 15 4.1.3 TEST PROCEDURES ............................................................................................ 16 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 16 4.1.5 TEST SETUP ......................................................................................................... 16 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 17 4.1.7 TEST RESULTS ..................................................................................................... 18 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 20 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 20 4.2.2 TEST INSTRUMENTS ........................................................................................... 21 4.2.3 TEST PROCEDURES ............................................................................................ 24 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 24 4.2.5 TEST SETUP ......................................................................................................... 25 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 25 4.2.7 TEST RESULTS (MODE 1) .................................................................................... 26 4.2.8 TEST RESULTS (MODE 2) .................................................................................... 30 4.3 6dB BANDWIDTH MEASUREMENT ..................................................................... 34 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 34 4.3.2 TEST INSTRUMENTS ........................................................................................... 34 4.3.3 TEST PROCEDURE .............................................................................................. 34 4.3.4 DEVIATION FROM TEST STANDARD .............…

Text truncated - open the document above for the full version.

Report No.: 131022E08 Page 1 Reference No.: PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 131022E08 Page 2 Reference No.: RADIATED EMISSION TEST (Below 1GHz) Report No.: 131022E08 Page 3 Reference No.: RADIATED EMISSION TEST (Above 1GHz)