K7SF7C043Wemo Maker

RELAY5V / 1A RESTOREI / O SENSOR RELAY5V / 1A RESTOREI / O SENSOR belkin.com/WeMo How to connect a device to WeMo Maker. Comment connecter un appareil à WeMo Maker. Ein Gerät an den WeMo Maker anschließen. Make sure the device is disconnected from any power sources. Assurez-vous que l’appareil est débranché de toute source d’alimentation. Stellen Sie sicher, dass das Gerät von allen anderen Stromquellen getrennt ist. Reconnect device connected to the Maker to its power sources. Re-branchez l’appareil connecté au Maker à sa source d’alimentation Schließen Sie das Gerät, das an den Maker angeschlossen ist, wieder an die entsprechenden Stromquellen an. Connect relay leads. Branchez les fils du relais. Schließen Sie die Relaisleitungen an (Note: Do not connect any device with voltage higher than 24VAC or 12VDC.) Remarque : ne branchez pas d’appareil dont la tension dépasse 24 V c.a. ou 12 V c.c.) Hinweis: Schließen Sie kein Gerät mit einer Spannung von mehr als 24 V Wechselspannung oder 12 V Gleichspannung an.) (Note: 5VDC at 100mA out, max. TTL Logic: Normally High, Triggered Low.) (Remarque : 5 V c.c. à 100 mA en sortie, max. TTL Logic : Normally High, Triggered Low.) (Hinweis: 5 V Gleichspannung/100 mA Ausgangsstrom, max. TTL-Logik: Normally High, Triggered Low.) Connect sensor leads. Branchez les fils du détecteur. Schließen Sie die Sensorleitungen an. Sie können sowohl Relaisleitungen als auch Sensorleitungen an Ihren WeMo Maker anschließen oder In Settings, select Wi-Fi. Connect to WeMo network. Sous Paramètres, sélectionnez Wi-Fi. Connectez- Wählen Sie in den Einstellungen Wi-Fi (WLAN) tellen Sie eine Verbindung zum WeMo- Launch the WeMo App to complete the setup. Ouvrez l’appli WeMo pour terminer l’installation. Podłącz do źródła zasilania USB. zęści Settings (Ustawienia) NEDERLANDS Een apparaat aansluiten op de WeMo Maker. Zorg ervoor dat het apparaat niet is aangesloten op een voedingsbron. s
Sluit de relaisdraden aan. Opmerking: Sluit geen apparaten aan die een voltage hebben dat hoger is dan 24 V AC of 12 V DC.) s
Sluit de sensordraden aan. (Opmerking: 5 V DC bij een uitgangsstroom van 100 mA, max TTL Logic: normaal hoog, getriggerd laag.) s
Wanneer het apparaat is aangesloten op de Maker, kunt u het weer aansluiten op de stroomvoorziening. ESPAÑOL Cómo conectar un dispositivo a WeMo Maker. Asegúrate de que el dispositivo está desenchufado de cualquier fuente de alimentación. s
Conecta los pines de relé. Nota: No conectes ningún dispositivo con un voltaje superior de 24 V CA o 12 V CC.) s
Conecta los pines del sensor (Nota: 5 V CC a 100 mA de salida, máx. lógica TTL: normalmente alta, baja al ejecutarse). s
Reconecta el dispositivo conectado al Maker a sus fuentes de alimentación. ITALIANO Come collegare un dispositivo a WeMo Maker. Accertarsi che il dispositivo sia scollegato da qualsiasi fonte di alimentazione. s
Collegare i conduttori del relè. Nota: Non collegare alcun dispositivo con voltaggio superiore a 24 V CA o 12 V CC. s
Collegare i conduttori del sensore. (Nota: uscita max. 5 V CC a 100 mA. Logica TTL: livello normalmente alto, impostato al livello basso.) s
Ricollegare il dispositivo collegato a WeMo Maker alla rispettiva fonte di SVENSKA Så här ansluter du en enhet till WeMo Maker. Kontrollera att enheten inte är ansluten till en strömkälla. s
Anslut reläkablarna. Obs! Anslut inte enheter med ett voltantal över 24 V likström eller 12 V växelström.) s
Anslut sensorkablar. (Obs: 5 V likström vid 100 mA uteJekt, max. TTL-logik: normalt hög, triggad låg.) s
Återanslut enheten som du kopplat till din Maker till dess strömkälla. ČESKY Jak připojíte zařízení k WeMo Maker. Zkontrolujte, že je zařízení odpojené od zdrojů napájení. s
Připojte vedení s relé. Poznámka: Nepřipojujte žádné zařízení s napětím vyšším než 24 V (střídavé napájení) nebo 12 V stejnosměrných.) s
Připojte vedení se snímačem. (Poznámka: 5 V stejnosměrných při 100 mA výstupu, max. logika TTL: normálně vysoká, sepnuto nízká.) s
Zařízení připojená k produktu Maker připojte znovu ke zdrojům napájení. POLSKI Podłączanie innego urządzenia do urządzenia WeMo Maker. Upewnij się, że urządzenie jest odłączone o źródła zasilania. s
Podłącz przewody przekaźników. Uwaga: Nie podłączaj urządzeń o napięciu wyższym niż 24 V AC lub 12 V DC. s
Podłącz przewody czujników. (Uwaga: Maks. napięcie wyjściowe: 5 V DC przy 100 mA, logika TTL: typowo stan wysoki, aktywacja w stanie niskim.) s
Urządzenia podłączone do WeMo Maker podłączyć do źródeł zasilania. MAGYAR Hogyan csatlakoztatható egy eszköz a WeMo Maker eszközhöz. Bizonyosodjon meg arról, hogy az eszköz nem csatlakozik semmilyen áramforráshoz. s
Csatlakoztassa a relé vezetékeit. Megjegyzés: Ne csatlakoztasson olyan eszközt, amelynek feszültsége nagyobb, mint 24 VAC vagy 12 VDC.) s
Csatlakoztassa az érzékelő vezetékeit. (Megjegyzés: 5 VDC 100 mA-es kimenet esetén, max. TTL logika: Alaphelyzetben magas, bekapcsolás alacsony szinten.) s
Csatlakoztassa ismét a Maker eszközhöz csatlakozó eszközt az áramforráshoz. SRPSKI Kako povezati neki uređaj na WeMo Maker. Vodite računa da je uređaj isključen iz svih izvora napajanja. s
Povežite vodove releja. Napomena: Nemojte povezivati uređaje čiji je napon veći od 24 VAC ili 12 VDC.) s
Povežite vodove senzora. (Napomena: 5 VDC na izlazu od 100 mA , maks. TTL Logic: Normalno visok, uključen nizak.) s
Ponovo povežite uređaj priključen na Maker na njegove izvore napajanja. ofessional electrician if tallation sécuri - ere Sicherungen er wenden. talleren. Als u geen ν στε άνετα tallation. Kontakta en behörig provádět elektrikářskou ESPAÑOL ¡ATENCIÓN! Este dispositivo representa un posible riesgo de descarga eléctrica. La instalación podría ser peligrosa o ilegal. Es posible que para garantizar una instalación segura sea necesario descargar o apagar múltiples disyuntores. Por favor llama a un electricista profesional si no estás acostumbrado o no te sientes cómodo trabajando con electricidad. Para conexiones de abastecimiento usa cables 14 AW…

Text truncated - open the document above for the full version.

Belkin International, Inc. 12045 East Waterfront Drive, Playa Vista, CA 90094 USA Declaration for no non-US channel operation October 1, 2014 We, Belkin International, Inc declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: K7SF7C043 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- Daniel Wesey / EMC Regulatory Compliance Engineer Belkin International, Inc. Tel: 310-751-2816 Fax: 310-751-5912 e-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Drive, Playa Vista, CA 90094 USA Date: 2014-09-03 FCC ID: K7SF7C043 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Daniel Wesey / EMC Regulatory Compliance Engineer Belkin International, Inc. Tel: 310-751-2816 Fax: 310-751-5700 e-mail: [email protected]

Belkin International, Inc. 12045 East Waterfront Drive, Playa Vista, CA 90094 USA Date: 2014-09-09 FCC ID: K7SF7C043 A U T H O R I Z A T I O N L E T T E R To whom it may concern: We, the undersigned, hereby authorize (Andrea Hsia ,Senior Specialist ) of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by (Andrea Hsia ,Senior Specialist )of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------- Daniel Wesey / EMC Regulatory Compliance Engineer Belkin International, Inc. Tel: 310-751-2816 Fax: 310-751-5912 e-mail: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4

Label Location

Page 5 Page 6 Page 7 Page 8

Report No.: SA140403C06 1 of 5 Report Format Version 5.0.1 RF EXPOSURE REPORT REPORT NO.: SA140403C06 MODEL NO.: F7C043fc FCC ID: K7SF7C043 RECEIVED: Apr. 03, 2014 TESTED: Jun. 18 ~ Sep. 17, 2014 ISSUED: Sep. 22, 2014 APPLICANT: Belkin International, Inc. ADDRESS: 12045 East Waterfront Drive, Playa Vista, CA 90094 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA140403C06 2 of 5 Report Format Version 5.0.1 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 3 1. CERTIFICATION ............................................................................................................................ 4 2. RF EXPOSURE ............................................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ....................................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................................. 5 2.3 CLASSIFICATION.......................................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................................ 5 Report No.: SA140403C06 3 of 5 Report Format Version 5.0.1 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140403C06 Original release Sep. 22, 2014 Report No.: SA140403C06 4 of 5 Report Format Version 5.0.1 1. CERTIFICATION PRODUCT: Wemo Maker MODEL NO.: F7C043fc BRAND: Belkin APPLICANT: Belkin International, Inc. TESTED: Jun. 18 ~ Sep. 17, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) KDB 447498 D03 IEEE C95.1 The above equipment (model: F7C043fc) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Sep. 22, 2014 Polly Chien / Specialist APPROVED BY : , DATE :Sep. 22, 2014 Ken Liu / Senior Manager Report No.: SA140403C06 5 of 5 Report Format Version 5.0.1 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away or higher as evaluated in following section. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 24.68 2.13 20 0.095 1 ---END---

Report No.: RF140403C06 1 of 56 Report Format Version 5.2.1 Reference No.: 140304C20 FCC TEST REPORT REPORT NO.: RF140403C06 MODEL NO.: F7C043fc FCC ID: K7SF7C043 RECEIVED: Apr. 03, 2014 TESTED: Jun. 18 ~ Sep. 17, 2014 ISSUED: Sep. 22, 2014 APPLICANT: Belkin International, Inc. ADDRESS: 12045 East Waterfront Drive, Playa Vista, CA 90094 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140403C06 2 of 56 Report Format Version 5.2.1 Reference No.: 140304C20 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 4 1. CERTIFICATION ............................................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ............................................................................................................ 7 3.1 GENERAL DESCRIPTION OF EUT .............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................................................ 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................................ 9 3.3 DUTY CYCLE OF TEST SIGNAL ................................................................................................ 12 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................ 13 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................................... 14 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................. 14 4. TEST TYPES AND RESULTS ..................................................................................................... 15 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................................... 15 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................... 15 4.1.2 TEST INSTRUMENTS ................................................................................................................. 16 4.1.3 TEST PROCEDURES ................................................................................................................. 17 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................................... 17 4.1.5 TEST SETUP ............................................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS ................................................................................................ 19 4.1.7 TEST RESULTS .......................................................................................................................... 20 4.2 CONDUCTED EMISSION MEASUREMENT .............................................................................. 34 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................... 34 4.2.2 TEST INSTRUMENTS ................................................................................................................. 34 4.2.3 TEST PROCEDURES ................................................................................................................. 35 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................................... 35 4.2.5 TEST SETUP ............................................................................................................................... 35 4.2.6 EUT OPERATING CONDITIONS ................................................................................................ 35 4.2.7 TEST RESULTS .......................................................................................................................... 36 4.3 6dB BANDWIDTH MEASUREMENT .......................................................................................... 38 4.3.1 …

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST