K7SMMA008Auto-Tracking Stand Pro with DockKit

Regulatory and Sustainability Information Safety Instructions WARNING: Failure to follow these instructions could result in fire, electric shock, injury, or damage to the user, product, or other property. 1. Operating Conditions: 0° C to 35° C 2. Keep this product out of reach of children as this product contains small parts such as battery cells which can be a choking and swallowing hazard. 3. Swallowing a battery may lead to severe burns (within 2 hours of ingestion), perforation of soft tissue, and death. In case of ingestion of a cell or battery, seek medical assistance immediately. 4. Do not expose this product to rain, snow, or any sources of liquids or moisture. 5. Keep this product away from heat sources such as fire, direct sunlight, and combustible gas. 6. Do not subject this product to crushing, bending, puncturing, or shredding. 7. Do not store your device in very hot or very cold locations. It is recommended to use your device at room temperature. 8. Unplug this product when not in use for long periods of time. 9. Avoid dropping or placing heavy objects on this product. 10. Use of a power supply not recommended or sold by Belkin may result in an increased risk of fire, electric shock, injury, or damage to the user, product, or other property 11. Wireless charging power transmission rate is regulated by the wireless charging device receiving power which can be influenced by factors like, but not limited to, proprietary charging protocols, ambient temperature, current battery percentage level and age of the device being charged. 12. Do not use this product if there are visible defects observed. 13.Do not attempt to service, modify, or disassemble this product. CAUTION: If you experience problems with this product, please discontinue use, and contact Belkin for assistance FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin International, Inc., of 555 S. Aviation Blvd., Suite 180, El Segundo, CA 90245, USA, Tel: +1(310) 751 5100, declare under our sole responsibility that this product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the distance between the equipment and the receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Innovation, Science, and Economic Development Canada Statement (ISED): This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Innovation, Science and Economic Development Canada Statement: This digital apparatus complies with CAN ICES-003(B) / NMB-003(B). Regulatory and Sustainability Information Safety Instructions WARNING: Failure to follow these instructions could result in fire, electric shock, injury, or damage to the user, product, or other property. 1. Operating Conditions: 0° C to 35° C 2. Keep this product out of reach of children as this product contains small parts such as battery cells which can be a choking and swallowing hazard. 3. Swallowing a battery may lead to severe burns (within 2 hours of ingestion), perforation of soft tissue, and death. In case of ingestion of a cell or battery, seek medical assistance immediately. 4. Do not expose this product to rain, snow, or any sources of liquids or moisture. 5. Keep this product away from heat sources such as fire, direct sunlight, and combustible gas. 6. Do not subject this product to crushing, bending, puncturing, or shredding. 7. Do not store your device in very hot or very cold locations. It is recommended to use your device at room temperature. 8. Unplug this product when not in use for long periods of time. 9. Avoid dropping or placing heavy objects on this product. 10. Use of a power supply not recommended or sold by Belkin may result in an increased risk of fire, electric shock, injury, or damage to the user, product, or other property 11. Wireless ch…

Text truncated - open the document above for the full version.

CFR 47 §2.911 (d)(5) Attestation Date: 1/9/2024 FCC ID: K7SMMA008 To: F ederal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1.Belk in International, Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2.Belk in International, Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sinc erely yours, Name: Zack Vogel Job Title: Sr. Regulatory Compliance Engineer Company Name: Belkin International, Inc.

CFR 47 §2.911 (d)(7) Agent Designation Attestation Date: 1/9/2024 FCC ID: K7SMMA008 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Belk in International, Inc. (“the applicant”) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. Jay Tu Belkin International, Inc. 555 S. Aviation Blvd., Suite 180, El Segundo, CA 90245, USA [email protected] FRN: 0008128605 Sin cerely yours, Zack Vogel Belkin International, Inc. 555 S. Aviation Blvd., Suite 180, El Segundo, CA 90245, USA [email protected]

Date: 1/9/2024 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a)fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC; b)supply any and all information needed for the evaluation of the products for which certification is sought; c)make claims regarding certification only in respect of the scope for which certification has been granted; d)not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized; e)discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification; f)use certification only to indicate that products are certified in conformity with specified standards; g)endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety; h)comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements; i)comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers; j)ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements; k)provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCB’s or the FCC’s market surveillance requirements; l)keep a record of all complaints relating to product’s compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies; m)inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant. Sincerely Yours, Zac k Vogel Sr. Regulatory Compliance Engineer Belkin International, Inc.

Date: 1/9/2024 Attn: FCC Office of Engineering and Technology / UL Verification Services TCB Subject: Request for Confidentiality FCC ID: K7SMMA008 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinit ely. •Schematic Diagram •Block Diagram •Operational Description •Antenna Specification Above mentioned documents contain detailed system and equipment descriptions and are considered proprietary information. The public disclosure of above documents might be harmful to our company and would give a competitor an unfair advantage in the market. In addition to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requesting the commission to grant short- term confidentiality on the following attachments until 180 days have passed after the grant has been published and released. •Ex ternal Photos •Internal Photos •Test Setup Photos •User Manual We understand that all test reports, test setup photos, RF Exposure Info, ID Label and location, and external photos which have been made available during the certification review process cannot be granted as confidential documents. We understand that these documents will be available for public review once the grant of equipment authorization is issued. Best Regards, Zack Vogel Sr. Regulatory Compliance Engineer Belkin International, Inc.

Power of Attorney Date: January 6, 2022 To whom it may concern: I, the undersigned, Jay Tu, hereby authorize the person(s) listed below to act on behalf of me to sign a ll related documents for Belkin International, Inc.’s FCC/IC application. Name: Zack Vogel / Sr. Regulatory Compliance Engineer, Regulatory Compliance Tel: +1 310 751 2800 E-mail: [email protected] Name: Rossi Wu / Senior Regulatory Compliance Engineer, Regulatory Compliance Tel: +1 310 633 9309 # 2960 E- mail: [email protected] Name: Da isy Dai / Regulatory Compliance Engineer, Regulatory Compliance Tel: O +86 755 2387 1039 E- mail: [email protected] Respectfully, Applicant’s company name: Belkin International, Inc. Applicant’s compa ny address: 555 S. Aviation Blvd., Suite 180, El Segundo, CA 90245, USA Signat ure Name a nd Job Title: Jay Tu / Manager, Regulatory Compliance E- mail: Jay. [email protected] Tel: +1 310 633 9309 # 9142

External Photos (Model: MMA008)

Internal Photos C222x Coil Antenna – To p V i e w C222x Coil Antenna – Botom View C222x PCB – To p V i ew C222x PCB – Botom View

TEST REPORT Report Number. : 14890696-E2V5 Applicant : BELKIN INTERNATIONAL, INC. 555 S. AVIATION BLVD., SUITE 180 EL SEGUNDO, CA 90245, USA Model : MMA008 FCC ID : K7SMMA008 EUT Description : Auto-Tracking Stand Pro with DockKit Test Standard(s) : FCC 47 CFR PART 1 SUBPART I FCC 47 CFR PART 2 SUBPART J Date Of Issue: 2024-02-13 Prepared by: UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 14890696-E2V5 DATE: 2024-02-13 FCC ID: K7SMMA008 MODEL NUMBER: MMA008 Page 2 of 20 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By V1 2024-01-23 Initial Issue --- V2 2024-01-30 Updated Section 1 Tina Chu V3 2024-02-05 Updated Section 6.3, 8, 9.1.1 and Page 19 to address TCB’s question. Tina Chu V4 2024-02-08 Updated Section 15 antenna gain Tina Chu V5 2024-02-13 Updated Section 12, 14, 15 address TCB’s question Tina Chu REPORT NO: 14890696-E2V5 DATE: 2024-02-13 FCC ID: K7SMMA008 MODEL NUMBER: MMA008 Page 3 of 20 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................4 2. TEST METHODOLOGY ......................................................................................................6 3. FACILITIES AND ACCREDITATION ..................................................................................6 4. DECISION RULES AND MEASUREMENT UNCERTAINTY (RF EXPOSURE) ..................7 4.1. METROLOGICAL TRACEABILITY ...............................................................................7 4.2. DECISION RULES ........................................................................................................7 4.3. MEASUREMENT UNCERTAINTY ................................................................................7 5. KDB 680106 D01 SECTION 5b EQUIPMENT APPROVAL CONSIDERATIONS ...............8 6. EQUIPMENT UNDER TEST ................................................................................................9 6.1. DESCRIPTION OF EUT ...............................................................................................9 6.2. SOFTWARE AND FIRMWARE .....................................................................................9 6.3. WORST-CASE CONFIGURATION AND MODE ...........................................................9 7. TEST AND MEASUREMENT EQUIPMENT ......................................................................10 8. DUTY CYCLE ....................................................................................................................11 9. MAXIMUM PERMISSIBLE RF EXPOSURE ......................................................................12 9.1. FCC LIMITS AND SUMMARY ....................................................................................12 9.1.1. MAXIMUM RESULT SUMMARY .........................................................................13 9.1.2. E- FIELD AND H- FIELD MEASUREMENTS .......................................................14 10. RF EXPOSURE TEST SETUP AND SETUP PHOTO........................................................14 11. DECISION RULES AND MEASUREMENT UNCERTAINTY (MPE CALCULATION/SAR EXCLUSION) ............................................................................................................................15 11.1. METROLOGICAL TRACEABILITY ..........................................................................15 11.2. DECISION RULES ..................................................................................................15 11.3. MEASUREMENT UNCERTAINTY ..........................................................................15 12. STANDALONE SAR TEST EXCLUSION CONSIDERATIONS .........................................16 12.1. FCC .........................................................................................................................16 13. MAXIMUM PERMISSIBLE EXPOSURE (LIMITS AND EQUATIONS) ..............................17 13.1. FCC RULES ............................................................................................................17 13.2. EQUATIONS ...........................................................................................................18 14. REFERENCES ..................................................................................................................19 15. RF EXPOSURE RESULTS ................................................................................................20 REPORT NO: 14890696-E2V5 DATE: 2024-02-13 FCC ID: K7SMMA008 MODEL NUMBER: MMA008 Page 4 of 20 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: BELKIN INTERNATIONAL, INC. 555 S. AVIATION BLVD., SUITE 180 EL SEGUNDO, CA 90245, USA EUT DESCRIPTION: Auto-Tracking Stand Pro with DockKit MODEL NUMBER: MMA008 BRAND: belkin SERIAL NUMBER: 57X10F6CD00603 SAMPLE RECEIPT DATE: 2023-12-21 DATE TESTED: 2023-12-28 TO 2024-01-02 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Complies UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The…

Text truncated - open the document above for the full version.

TEST REPORT Report Number. : 14890696-E5V4 Applicant : BELKIN INTERNATIONAL, INC. 555 S. AVIATION BLVD., SUITE 180 EL SEGUNDO, CA 90245, USA Model : MMA008 Brand : belkin FCC ID : K7SMMA008 IC : 3623A-MMA008 EUT Description : Auto-Tracking Stand Pro with DockKit Test Standard(s) : FCC 47 CFR PART 15 SUBPART C ISED RSS-247 ISSUE 3 ISED RSS-GEN ISSUE 5 + A1 + A2 Date Of Issue: 2024-02-09 Prepared by: UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 14890696-E5V4 DATE: 2024-02-09 FCC ID: K7SMMA008 IC: 3623A-MMA008 Page 2 of 59 UL VERIFICATION SERVICES 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL VERIFICATION SERVICES REPORT REVISION HISTORY Rev. Issue Date Revisions Revised By V1 2024-01-19 Initial Issue -- V2 2024-02-05 Updated Section 1, 10.5 to address TCB’s questions Tina Chu V3 2024-02-08 Updated Section 6.3 antenna gain Tina Chu V4 2024-02-09 Updated RSS-247 to Issue 3 F. de Anda REPORT NO: 14890696-E5V4 DATE: 2024-02-09 FCC ID: K7SMMA008 IC: 3623A-MMA008 Page 3 of 59 UL VERIFICATION SERVICES 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL VERIFICATION SERVICES TABLE OF CONTENTS REPORT REVISION HISTORY ..................................................................................................2 TABLE OF CONTENTS .............................................................................................................3 1. ATTESTATION OF TEST RESULTS ..................................................................................5 2. TEST RESULTS SUMMARY ...............................................................................................7 3. TEST METHODOLOGY ......................................................................................................8 4. FACILITIES AND ACCREDITATION ..................................................................................8 5. DECISION RULES AND MEASUREMENT UNCERTAINTY ...............................................9 5.1. METROLOGICAL TRACEABILITY ...............................................................................9 5.2. DECISION RULES ........................................................................................................9 5.3. MEASUREMENT UNCERTAINTY ................................................................................9 5.4. SAMPLE CALCULATION ...........................................................................................10 6. EQUIPMENT UNDER TEST ..............................................................................................11 6.1. EUT DESCRIPTION ...................................................................................................11 6.2. MAXIMUM OUTPUT POWER .....................................................................................11 6.3. DESCRIPTION OF AVAILABLE ANTENNAS AND CABLE LOSS ..............................11 6.4. SOFTWARE AND FIRMWARE ...................................................................................11 6.5. WORST-CASE CONFIGURATION AND MODE .........................................................12 7. MEASUREMENT METHOD...............................................................................................13 8. TEST AND MEASUREMENT EQUIPMENT ......................................................................14 9. ANTENNA PORT TEST RESULTS ...................................................................................15 9.1. ON TIME AND DUTY CYCLE .....................................................................................15 9.2. 99% BANDWIDTH ......................................................................................................17 9.2.1. BLE (1Mbps) ........................................................................................................17 9.2.2. BLE (2Mbps) ........................................................................................................18 9.3. 6 dB BANDWIDTH ......................................................................................................19 9.3.1. BLE (1Mbps) ........................................................................................................19 9.3.2. BLE (2Mbps) ........................................................................................................20 9.4. OUTPUT POWER .......................................................................................................21 9.4.1. BLE (1Mbps) ........................................................................................................21 9.4.2. BLE (2Mbps) ........................................................................................................21 9.5. AVERAGE POWER ....................................................................................................22 9.5.1. BLE (1Mbps) ........................................................................................................22 REPORT NO: 14890696-E5V4 DATE: 2024-02-09 FCC ID: K7SMMA008 IC: 3623A-MMA008 Page 4 of 59 UL VERIFICATION SERVICES 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL VERIFICATION SERVICES 9.5.2. BLE (2Mbps) ........................................................................................................22 9.6. POWER SPECTRAL DENSITY ..................................................................................23 9.6.1. BLE (1Mbps) ........................................................................................................23 9.6.2. BLE (2Mbps) .......................................................................................................…

Text truncated - open the document above for the full version.

ANTENNA GAIN AND PATTERN MEASUREMENT REPORT For Gain value reference FOR AUTO-TRACKING STAND PRO WITH DOCKKIT PART/MODEL NUMBER: MMA008 DATE ISSUED: February 9, 2024 REPORT NUMBER: 14890696-O1V1 Prepared for Belkin International, Inc. 555 S. Aviation Blvd., Ste 180 El Segundo, California, 90245 U.S.A. Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 14890696-O1V1 DATE: February 09, 2024 EUT: Auto-Tracking Stand Pro with Dock Kit PART/MODEL: MMA008 Page 2 of 16 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By V1 Initial Issue Ekta Budhbhatti REPORT NO: 14890696-O1V1 DATE: February 09, 2024 EUT: Auto-Tracking Stand Pro with Dock Kit PART/MODEL: MMA008 Page 3 of 16 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. TABLE OF CONTENTS 1 ATTESTATION OF TEST RESULTS ............................................................................................. 4 2 TEST METHODOLOGY ................................................................................................................. 5 3 TEST FACILITY ............................................................................................................................. 5 4 TEST AND MEASUREMENT EQUIPMENT ................................................................................... 5 5 DEVICE UNDER TEST INFORMATION ......................................................................................... 6 6 RESULT SUMMARY ...................................................................................................................... 6 6.1 Active Antenna Pattern ............................................................................................................ 6 7 PLOTS ........................................................................................................................................... 7 7.1 3D ACTIVE- 2402 MHz ............................................................................................................ 7 7.2 3D ACTIVE- 2440 MHz .......................................................................................................... 10 7.3 3D ACTIVE- 2480 MHz .......................................................................................................... 13 8 TEST SETUP ............................................................................................................................... 16 REPORT NO: 14890696-O1V1 DATE: February 09, 2024 EUT: Auto-Tracking Stand Pro with Dock Kit PART/MODEL: MMA008 Page 4 of 16 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 1 ATTESTATION OF TEST RESULTS Company Name and Address Belkin International, Inc. 555 S. Aviation Blvd., Ste 180 El Segundo, CA 90245 U.S.A. EUT Description Auto Tracking Stand Pro with DockKit Part/Model MMA008 Date Tested 02/07/2024-02/08/2024 APPLICABLE STANDARDS STANDARD TEST RESULTS Non-standard Test Method: Information Only UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical c…

Text truncated - open the document above for the full version.