KA2DFM-562BD-Link Bluetooth Modem

Conexant SC56D BT Modem 15.21 CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Prohibition of co-location This device must not be co-located or operating in conjunction with any other antenna or transmitter 15.105 Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. MPE Statement (Safety Information) Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. Conexant SC56D BT Modem 2 Safety Information In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. Caution Statement of the FCC Radio Frequency Exposure This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation—as a mobile or portable device but use in a body-worn way is strictly prohibit. When using this device, a certain separation distance between antenna and nearby persons has to be kept to ensure RF exposure compliance. In order to comply with the RF exposure limits established in the ANSI C95.1 standards, the distance Conexant SC56D BT Modem 3 between the antennas and the user should not be less than 20cm. How to use BT Modem The CD includes below: 1. \ Manual \: Modem manual. 2. \Acrobat\:Acrobat reader 4.0. 3. Run BVRP\setup.exe to install BVRP or other software. Note: The detailed manual has been put into PDF file in the CD, please run Acrobat Reader 4.0 to read it. Connect Windows 98/ME 1. Double click the My Bluetooth Places icon on desktop screen. 2. Select “Entire Bluetooth Neighborhood” to search Bluetooth Devices in proximity. You will find a Bluetooth Modem icon on the list if you have plug in phone line and power on V90 Modem AP successfully. 3. When dongle find Bluetooth device, it will be show “DFM-560BT” then double-click on this icon. 4. A pup up dialogue from task bar asks you to enter Pin code for passkey authentication. 5. Enter Bluetooth Passkey (PingCode) and click OK. You can get Ping Code from the bottom of V90 modem AP. 6. Click Dial-up Networking. 7. Fill in your dial-up username, password, and the phone number to be dialed, and then click the Dial button. Select the Save password check Conexant SC56D BT Modem 4 box and the dialog box will not appear for subsequent connections to the same phone number. 8. It takes seconds to connect to the Internet. 9. The Dial Up Networking Icon turns Green when connection established. You can now open a web browser and surf the Internet wirelessly. Windows 2000/XP 1. Double click the My Bluetooth Places icon on desktop screen. 2. Click “Search for devices in range” to find Bluetooth device. 3. When dongle find Bluetooth device, it will be show “DFM-560BT” then double-click on this icon. 4. A pup up dialogue from task bar asks you to enter Pin code for passkey authentication. 5. Enter Bluetooth Passkey (PingCode) and click OK. You can get Ping Code from the bottom of V90 modem AP. 6. Click Dial-up Networking. 7. Fill in your dial-up username,password,and the phone number to be dialed,and then click the Dial button.Select the Save password check box and the dialog box will not appear for subsequent connections to the same phone number. 8. It takes seconds to connect to the Internet. 9. The Dial Up Networking Icon turns Green when connection established. You can now open a web browser and surf the Internet wirelessly. FAX Windows 98/ME 1. Double click the My Bluetooth Places icon on desktop screen. 2. Click “Search for devices in range” to find Bluetooth device. 3. When dongle find Bluetooth device, it will be show “DFM-560BT” then double-click on this icon. Conexant SC56D BT Modem 5 4. Click Fax. 5. The Fax Icon turns Green when Fax function is established. Please installed BVRP. 6. If you are using Fax again all you need is to initialize “BVRP Tools to start Fax function. Windows 2000/XP 1. Double click the My Bluetooth Places icon on desktop screen. 2. Click “Search for devices in range” to find Bluetooth device. 3. When dongle find Bluetooth device, it will be show “DFM-560BT” then double-click on this icon. 4. Click Fax. 5. The Fax Icon turns Green when Fax function is established. Please installed BVRP. 6. If you are using Fax again all you need is to initialize “BVRP Tools to …

Text truncated - open the document above for the full version.

Request for Confidentiality Federal Communications Commission Authorization and Evaluation Division Sub.: Confidentiality Request regarding application for certification of FCC ID : KA2DFM-562B Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: l Schematics l Part List l Block diagram l Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, C.C. Tsai / Manager

External Photos of Bluetooth Modem1/4 FCC ID:KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of Bluetooth Modem2/4 FCC ID:KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of Bluetooth Modem3/4 FCC ID:KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of Bluetooth Modem4/4 FCC ID:KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

LABEL Format: LABEL Size: 70 x 55 mm LABEL Position: DFM-562BT KA2DFM-562B

Internal Photos of Bluetooth Modem1/4 FCC ID: KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of Bluetooth Modem2/4 FCC ID: KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of Bluetooth Modem3/4 FCC ID: KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of Bluetooth Modem4/4 FCC ID: KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Training Research Co., Ltd. No. 255, Nan-yang Street, Shijr City, Taipei Hsien 221, Taiwan Tel: 886-2-26935155 Fax: 886-2-26934440 e-mail: [email protected] 1 of 2 TRCSince1985 ® Measurement of MPE 1. Foreword In adopt with the Human Exposure IEEE C95.1, and according to the FCC 1.1310. The Maximum Permissible Exposure (MPE) is obligated to measure in order to prove the safety of radiation harmfulness to the human body. The Gain of the antenna used is measured in an Anechoic chamber. The maximum total power to the antenna is to be recorded. By adopting the Friis Transmission Formula and the power gain of the antenna, we can find the distance right away from the product, where the limit of the MPE is. 2. Description of EUT Granted FCC ID : KA2DFM-562B Product name : Bluetooth Modem Model name : DFM-562BT Classification : Mobile Device (i) Under normal use condition, the antenna is at least 20cm away from the user; (ii) Warning statement for keeping 20cm separation distance and the prohibition of operating next to the person has been printed in the user’s manual Frequency Range : 2.400 GHz ~ 2.4835GHz Supported Channel : 80 Channel Channel Spacing : 1MHz Modulation Skill : GFSK Power Type : Powered by AC to AC Adaptor Model: MW41-0900800A I/P: AC 120V, 60Hz O/P: AC 9V, 800mA Training Research Co., Ltd. No. 255, Nan-yang Street, Shijr City, Taipei Hsien 221, Taiwan Tel: 886-2-26935155 Fax: 886-2-26934440 e-mail: [email protected] 2 of 2 TRCSince1985 ® 3. Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Filed Strength (H) (A/m) Power Density (S) (mW/cm2) Averaging Time |E| 2 , |H| 2 or S (minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 100 6 3.0-30 1842/f 4.89/f 900/f 2 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- f/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 100 30 1.34-30 824/f 2.19/f 180/f 2 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- f/1500 30 1500-100,000 -- -- 1.0 30 [The EUT is tested in transmit and receive modes and in the first, middle and the last channel separately. The following shows only our observation have the greatest emissions.] According to OET BULLETIN 56 Fourth Edition/August 1999, Equation for Predicting RF Fields: Friis Transmission Formula: 24 22 /10223.3 )20(4 897.1854.0 4 cmmW R PG S − ×= × == ππ Estimated safe separation: cm PG R359.0 4 897.1854.0 4 = × == ππ Remarks: "The safe estimated separation that the user must maintain from the antenna is at least 0.359 cm." Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) The Numeric gain G of antenna with a gain specified in dB is determined by: G = Log -1 ( dBi antenna gain / 10 ) G = Log -1 (2.78 / 10) = 1.897 SPECIFICATION 1. Description Flying Lead Swivel Type 1/4λ Dipole Antenna (Gray ) 2. Customer 3. Model No. WFL002 4. Part No. SLW0010A 5. Standard IEEE 802.11b 11Mbps Wireless LAN 6. Antenna Profile 108 mm length (see Drawing) 7. Color Gray(424U) 8. Electrical Characteristics Operating Frequency 2.4~2.5Ghz Antenna Type 1/4λ Dipole Sleeve Polarization Type Linear Type of Radiation Toroidal Antenna Gain 2.78 dBi Typical Impedance 50 Ohm nominal V.S.W.R. 2.0:1 Max. 9. Mechanical Characteristics Action Swivel Type Holder With Connector N/A Core N/A 10. Raw Material Coaxial Cable MIL-C-17 RG-178 B/U Housing TPU Hinge Polycarbonate Coaxial Cable Data Sheet RG-178 SPECIFICATION FOR APPROVAL A30178B001 200 30V RG-178B/U SIZE: 7/0.102 SCCS RECOGNIZED: WONDERFUL HI-TECH CO.,LTD OFFICE72WU KONG 6TH ROAD, WU KU IND. DISTRICT TAIPEI HSIEN,TAIWAN TEL(02)22988033 FAX(02)22988031-2 FAC TORY17 PEI YUAN ROAD, CHUNG-LI IND. PARK TAIWAN, R.O.C. TEL(03)4527777 FAX(03)4517214 WONDERFUL HI-TECH CO., LTD SPECIFICATION STYLE 200 30V COAXIAL DOCUMENT NO : A30178B001 SIZE RG-178B/U ESTABLISHED DATE: 2003/02/13 STANDARD : MIL-C-17 Size AWG 30 Material ---- Silver-Coated Copper Clad Steel Conductors No. ---- 7 Conductors Size mm 0.102 Conductor O.D. mm 0.30 Average Thickness mm 0.28 Diameter mm 0.86 Material ---- FEP Insulation Color ---- Clear Material ---- Silver-Coated Copper Construction mm 16 / 3 / 0.10 Braid Coverage % 95 Average Thickness mm 0.25 Diameter mm 1.80 0.05 Material ---- FEP Jacket Color ---- Brown Marking Drawing AK001/210X297/1.0 PAGE : 1 EDITION : 1.1 REVISED DATE : MAKER : C.Y.CHEN CONFIRM : S.N.WONG APPROVAL : W.J.WANG WONDERFUL HI-TECH CO., LTD SPECIFICATION Electrical & Physical Properties Item RG-178B/U Rating Temp Voltage 200 30V Conductor Resistance 838 OHM/KM/20 MAX. Insulation Resistance 3000 MEGA OHM/KM MIN. Dielectric Strength AC 1.0 KV/Minute Spark Test 2.0 KV Tensile Strength 2500 PSI MIN.( 1.76 Kg / ) Unaged Elongation 200% MIN. Tensile StrengthUNAGED MIN 75%(168HRS×232) Insulation Aged Elongation UNAGED MIN 75%(168HRS×232) Tensile Strength 2500 PSI MIN.( 1.76 Kg / ) Unaged Elongation 200% MIN. Tensile StrengthUNAGED MIN.75%(168HRS×232) Jacket Aged Elongation UNAGED MIN.75%(168HRS×232) Nom. Impedance 50 Ohms Nom. Capacitance 95.8 pF/m Nom. Vel. of Prop. 69.5% VSWR (0 – 6 GHZ) UNDER 1.3 100MHz 1GHz 1.8GHz 2.4GHz 5.2GHz 6GHz Attenuation (dB/100m) 46 155 295 340 505 550 AK001/210X297/1.0 PAGE : 2 EDITION : 1.1 REVISED DATE : MAKER : C.Y.CHEN CONFIRM : S.N.WONG APPROVAL : W.J.WANG

Test Report -------------------------------------------------------------------------------1/37 Report No.: D1815688, FCC Part 15 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 MEASUREMENT REPORT of Bluetooth Modem Applicant:D-Link Corporation EUT:Bluetooth Modem Model No.:DFM-562BT FCC ID:KA2DFM-562B Report No.:D1815688 Tested by : Training Research Co., Ltd. TEL : 886-2-26935155 FAX : 886-2-26934440 No. 255, Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. Test Report -------------------------------------------------------------------------------2/37 Report No.: D1815688, FCC Part 15 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 CERTIFICATION We here by verify that: The test data, data evaluation, test procedures and equipment configurations shown in this report were made mainly in accordance with the procedures given in ANSI C63.4 (1992) as a reference. All test were conducted by Training Research Co., Ltd., No. 255, Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. Also, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report isin compliance with the technical requirements set forth in the FCC Rules Part 15 Subpart C Section 15.247. Applicant:D- LinkCorporation Applicant address:No. 8, Li-Hsin VII Road, Science Based Industrial Park, Hsin-Chu, Taiwan, R.O.C. Product name:D-Link Bluetooth Modem Modelname:DFM-562BT FCC ID:KA2DFM-562B Report No.:D1815688 Test Date:May 29, 2003 Prepared by:Approved by: Jack Tsai Frank Tsai Conditions of issue : (1) This test report shall not be reproduced except in full, without written approval of TRC. And the test result contained within this report only relate to the sample submitted for testing. (2) This report must not be used by the client to claim product endorsement by NVLAP or any agency of U.S. Government. NVLAP LAB CODE: 200174-0 Test Report -------------------------------------------------------------------------------3/37 Report No.: D1815688, FCC Part 15 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Tables of Contents I.GENERAL......................................................................................................................... 5 1.1 Introduction.................................................................................................................. 5 1.2 Description of EUT ....................................................................................................... 5 1.3 Test method .................................................................................................................. 5 1.4 Description of Support Equipment ................................................................................. 6 1.5 Configuration of System Under Test .............................................................................. 7 1.6 Test Procedure ............................................................................................................. 8 1.7 Location of the Test Site ................................................................................................ 8 1.8 General Test Condition .................................................................................................. 8 II. Section 15.203 : Antenna Requirement.............................................................................. 9 III.Section 15.207 : Power Line Conducted Emissions for AC Powered Units................... 10 3.1 Test Condition & Setup ................................................................................................ 10 3.2 List of Test Instruments ................................................................................................ 10 3.4 TestResults of Conducted Emissions ............................................................................ 11 IV. Section 15.247(a) : Technical Description of the EUT..................................................... 15 V.Section 15.247(a)(1) : Carrier Frequency Separation....................................................... 16 5.1 Test Condition............................................................................................................. 16 5.2 Test Instruments Configuration ...................................................................................... 16 5.3 List of Test Instruments................................................................................................ 17 5.4 TestResults................................................................................................................. 17 VI. Section 15.247(a)(1)(ii) : Number of Hopping Frequencies ............................................ 18 6.1 Test Condition............................................................................................................. 18 6.2 List of Test Instruments ................................................................................................ 18 6.3 TestInstrumentsConfiguration...................................................................................... 18 6.4 Test Results................................................................................................................. 19 Test Report -------------------------------------------------------------------------------4/37 Report No.: D1815688, FCC Part 15 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 VII. Section 15.247(a)(1)(ii) : Time of Occupancy (Dwell time) ............................................. 20 7.1 Test Condition............................................................................................................. 20 7.2 List of Test Instruments ................................................................................................ 20 7.3 TestInstrumentsConfiguration...................................................................................... 21 7.4 Test Results...................…

Text truncated - open the document above for the full version.

Test Setup Photos ------------------------------------------------------------------------ 1/2 FCC ID: KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Conducted Test Setup Placement: Front View of the Test Configuration Side View of the Test Configuration Test Setup Photos ------------------------------------------------------------------------ 2/2 FCC ID: KA2DFM-562B Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Radiated Test Setup Placement: Front View of the Test Configuration of Intentional Rear View of the Test Configuration of Intentional