KR5WLC-CEM02Wireless Power Charger

User Manual CONTINENTAL WLC WLC-CEM02 Wireless Power Charger 1.System description Continental Wireless Power Charger is developed for automotive applications under the name WLC. It includes one function: -WPC: Wireless Power Charging WPC parameters Parameters Values Carrier frequency 126.7 kHz Frequency shift +/-6 kHz Supply voltage 13.5V battery Voltage supply range 8V < V BAT < 16V Max. supply power 33W Operating temperature range* Smartphone operating temperature range -40°C < Temp < 85°C -20°C < Temp < 60°C Max. Output Power on receiver load** 11W WPC chipset brand Renesas WPC litz coil Single coil MPA14 according to Qi standard WPC litz coil gain @ 126.7kHz -108.3dBi Dimensions (X/Y/Z in mm) 142 x 91.5 x 23.5 Product weight 150 g Vehicle fuse protection 10 A Vehicle installation Although the WLC module is intended for different vehicles, it is always installed in the vehicle front central console (see an example in Figure 7). Figure 7. Location of WLC inside the vehicle The installation with the shortest distance to the human body is illustrated in Figure 8: 11.26cm. Figure 8. Shortest distance to human body Warning statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement

KDB 680106 for WPT exclusion requirements FCC ID: KR5WLC-CEM02 KDB 680106 D01 Section 5.b Requirements Product Specification Result (1) Power transfer frequency is less than 1 MHz.0.1267MHz Complied (2) Output power from each primary coil is less than or equal to 15 watts. 11 watts. Complied (3) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Single Coil Complied (4) Client device is placed directly in contact with the transmitter. Client device is not placed directly in contact with the transmitter. It’s docked onto the WPT. Not Complied (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Mobile exposure conditions only Complied (6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit Please refer to the test result of RF exposure report that are demonstrated to be less than 50% of the MPE limit. Complied

Applicant Declaration Applicant Declaration Rev:0. 0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Continental Automotive GmbH Address Siemensstrasse 12 SV C TS RBG EMC-Laboratory Regensburg, 93055, Germany Grantee Code KR5 FCC ID KR5WLC-CEM02 Authorized Contact Name Dagmar Kolar Contact Email [email protected] Contact Phone 49-941-790-6699 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees t hat a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: April 12, 2021 Print Name: Dagmar Kolar Title: Type approval employee *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Date: April 12, 2021 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID:KR5WLC-CEM02 To whom it may concern: We, the undersigned, hereby authorize Kevin Tsai / Deputy Manager of SGS Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Continental Automotive GmbH. This authorization is valid until further written notice from the applicant. Dagmar Kolar / Type approval employee Continental Automotive GmbH Phone: 49-941-790-6699 E-Mail: [email protected]

Date: April 12, 2021 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Continental Automotive GmbH Siemensstrasse 12 ,93055 Regensburg, Germany Regarding: Confidentiality Request regarding application for FCC ID: KR5WLC-CEM02 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the publi c. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Dagmar Kolar / Type approval employee Continental Automotive GmbH Phone: 49-941-790-6699 E-Mail: [email protected]

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 1 / 7 Report No.: T201130W02 Rev.: 01 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 7 Report No.: T201130W02 Rev.: 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 7 Report No.: T201130W02 Rev.: 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 7 Report No.: T201130W02 Rev.: 01

Label design Wireless Power Charger WLC-CEM02 FCC ID: KR5WLC-CEM02 IC: 7812D-WLCCEM02 Removable Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 5 / 7 Report No.: T201130W02 Rev.: 01 INTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 6 / 7 Report No.: T201130W02 Rev.: 01 PCB This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 7 / 7 Report No.: T201130W02 Rev.: 01 Antenna RF IC & Crystal

FCC ID: KR5WLC-CEM02 Page: 1 / 8 Report No.: T201130W02-MF Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group KDB 680106 D01 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 RF EXPOSURE REPORT For Wireless Power Charger Model: WLC-CEM02 Trade Name: Continental Issued to Continental Automotive GmbH Siemensstrasse 12 SV C TS RBG EMC-Laboratory Regensburg, 93055, Germany Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issued Date: April 29, 2021 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 8 Report No.: T201130W02-MF Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 April 20, 2021 Initial Issue ALL Doris Chu 01 April 29, 2021 See the following Note Rev.(01) P.5, 7 Doris Chu Note: Rev.(01) 1. Revised remark in section 2. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 8 Report No.: T201130W02-MF Rev.: 01 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ......................................................................... 4 2. EUT SPECIFICATION .......................................................................................... 5 3. MEASUREMENT EQUIPMENT USED ................................................................. 6 4. LIMIT ..................................................................................................................... 7 5. TEST RESULTS ................................................................................................... 8 6. PHOTOGRAPHS OF TEST SETUP ................................................................. A-1 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 8 Report No.: T201130W02-MF Rev.: 01 1. TEST RESULT CERTIFICATION APPLICABLE STANDARDS STANDARD TEST RESULT KDB 680106 D01 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 No non-compliance noted Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Approved by: Kevin Tsai Deputy Manager Compliance Certification Services Inc. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 5 / 8 Report No.: T201130W02-MF Rev.: 01 2. EUT SPECIFICATION EUT Wireless Power Charger Model WLC-CEM02 Trade Name Continental Model Discrepancy N/A Frequency band (Operating) 100KHz ~ 145KHz Others Device category Portable (<20cm separation) Mobile (>20cm separation) Others Exposure classification Occupational/Controlled exposure General Population/Uncontrolled exposure (E=614 V/m) Antenna Specification Coil Antenna Evaluation applied MPE Evaluation* SAR Evaluation N/A Received Date November 30, 2020 Date of Test January 27, 2021 Remark: 1. Disclaimer: Antenna information is provided by the applicant, test results of this report are applicable to the sample EUT received. 2. According to customer declaration, the EUT have two types for sale. The difference of the variants are the CAN communication speed (Low Speed (LS) & High Speed (HS)) in the vehicle which doesn’t affect the RF characteristics & functions. 3. All variants of the EUT were pre-scanned for the radiated measurement. The worst case is Low Speed (LS). This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 6 / 8 Report No.: T201130W02-MF Rev.: 01 3. MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement RF Conducted Test Site Equipment Manufacturer Model S/N Cal Date Cal Due Field Meter Wavecontrol SMP2 19SN1198 08/12/2019 08/11/2021 Probe (1Hz~400kHz) Wavecontrol WP400 19WP100597 08/12/2019 08/11/2021 Software N/A This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 7 / 8 Report No.: T201130W02-MF Rev.: 01 4. LIMIT Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(b), 1.1310. §1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b), except in the case of portable dev…

Text truncated - open the document above for the full version.

FCC ID: KR5WLC-CEM02 Page 1 / 27 Report No.: T201130W02-RP Rev. 02 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC 47 CFR PART 15 SUBPART C TEST REPORT For Wireless Power Charger Model: WLC-CEM02 Trade Name: Continental Issued to Continental Automotive GmbH Siemensstrasse 12 SV C TS RBG EMC-Laboratory Regensburg, 93055 Germany Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issued Date: April 29, 2021 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 2 / 27 Report No.: T201130W02-RP Rev. 02 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 April 20, 2021 Initial Issue ALL Doris Chu 01 April 28, 2021 See the following Note Rev.(01) P.15, 20-21 Doris Chu 02 April 29, 2021 See the following Note Rev.(02) P.5, 9 Doris Chu Note: Rev.(01) 1. Revised 20dB test procedure. 2. Added remark description. Rev.(02) 1. Revised test mode description. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 3 / 27 Report No.: T201130W02-RP Rev. 02 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ......................................................................................... 4 2. EUT DESCRIPTION ............................................................................................................. 5 3. TEST SUMMARY ................................................................................................................. 6 4. TEST METHODOLOGY ....................................................................................................... 7 4.1 EUT CONFIGURATION .................................................................................................. 7 4.2 EUT EXERCISE .............................................................................................................. 7 4.3 GENERAL TEST PROCEDURES ................................................................................... 7 4.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................................ 8 4.5 DESCRIPTION OF TEST MODES .................................................................................. 9 5. INSTRUMENT CALIBRATION ........................................................................................... 10 5.1 MEASURING INSTRUMENT CALIBRATION ................................................................ 10 5.2 MEASUREMENT EQUIPMENT USED .......................................................................... 10 5.3 MEASUREMENT UNCERTAINTY ................................................................................ 12 6. FACILITIES AND ACCREDITATIONS ............................................................................... 13 6.1 FACILITIES ................................................................................................................... 13 6.2 EQUIPMENT ................................................................................................................. 13 7. SETUP OF EQUIPMENT UNDER TEST ............................................................................ 14 7.1 SETUP CONFIGURATION OF EUT .............................................................................. 14 7.2 SUPPORT EQUIPMENT ............................................................................................... 14 8. TEST REQUIREMENTS ..................................................................................................... 15 8.1 20dB BANDWIDTH ....................................................................................................... 15 8.2 TRANSMITTER RADIATED EMISSION ........................................................................ 17 8.3 AC CONDUCTED EMIISION......................................................................................... 26 8.4 ANTENNA REQUIREMENT .......................................................................................... 27 APPENDIX A PHOTOGRAPHS OF TEST SETUP ................................................................. A-1 APPENDIX 1 - PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 4 / 27 Report No.: T201130W02-RP Rev. 02 1. TEST RESULT CERTIFICATION Applicant: Continental Automotive GmbH Siemensstrasse 12 SV C TS RBG EMC-Laboratory Regensburg, 93055, Germany Manufactur…

Text truncated - open the document above for the full version.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-10 Report No.: T201130W02-MF Rev.: 01 6. PHOTOGRAPHS OF TEST SETUP Probe Position Front 8 cm 10 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-10 Report No.: T201130W02-MF Rev.: 01 15 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-3 / A-10 Report No.: T201130W02-MF Rev.: 01 Probe Position Back 8 cm 10 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-4 / A-10 Report No.: T201130W02-MF Rev.: 01 15 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-5 / A-10 Report No.: T201130W02-MF Rev.: 01 Probe Position Left Side 8 cm 10 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-6 / A-10 Report No.: T201130W02-MF Rev.: 01 15 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-7 / A-10 Report No.: T201130W02-MF Rev.: 01 Probe Position Right Side 8 cm 10 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-8 / A-10 Report No.: T201130W02-MF Rev.: 01 15 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-9 / A-10 Report No.: T201130W02-MF Rev.: 01 Probe Position Top 8 cm 10 cm This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-10 / A-10 Report No.: T201130W02-MF Rev.: 01 20 cm

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page A-1 / A-2 Report No.: T201130W02-RP Rev. 02 APPENDIX A PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION SETUP PHOTOS Low Speed 9 kHz - 30 MHz Below 1GHz This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page A-2 / A-2 Report No.: T201130W02-RP Rev. 02 High Speed RF Conducted Emission Setup Photo